ASKO D5536XXLFISOF (01) PDF Document

The front panel of your ASKO D5536XXLFISOF dishwasher has the following touch buttons and indicators:

1. On/Left-on mode: Turns the dishwasher on or off.

2. Program selector: Selects the desired wash program.

3. Program symbol: Displays the symbol for the selected program.

4. Display: Shows program time, settings, and other information.

5. Rinse aid indicator: Lights up when rinse aid needs to be refilled.

6. TAB (3-in-1/all-in-one detergent): Button to activate the setting for combination detergents.

7. Salt indicator: Lights up when dishwasher salt needs to be refilled.

8. Child lock (button lock): Indicates if the child lock is active.

9. High temperature: Option button to increase the main wash temperature.

10. Long dry: Option button to improve drying results.

11. Delayed start: Option button to delay the start of the program.

12. Start/Stop: Starts or stops the selected program.

Note: Two minutes after the last button press, the panel backlight enters energy-saving mode. To reactivate the panel, close and reopen the door, or press the On/Left-on mode button.

When using your ASKO D5536XXLFISOF dishwasher, please follow these basic precautions:

• Read all instructions before use.

• Use the dishwasher only for its intended function.

• Use only detergents recommended for dishwashers and keep them out of reach of children.

• When loading items: locate sharp items so they are not likely to damage the door seal, and load sharp knives with handles up to reduce the risk of injury.

• Do not wash plastic items unless marked “dishwasher safe”.

• Do not operate the dishwasher unless all enclosure panels are properly in place.

• Do not tamper with controls.

• Do not abuse, sit on, or stand on the door or dish rack.

• Do not allow children to play in or on the dishwasher.

• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the dishwasher, turn on all hot water faucets and let water flow for several minutes to release any accumulated hydrogen gas. Do not smoke or use an open flame during this time.

• Remove the door to the washing compartment when removing an old dishwasher from service or discarding it.

• Always keep small children away from the machine when it is open, as detergent residue may be left inside.

You can activate the child lock (button lock) to prevent children from starting the ASKO D5536XXLFISOF dishwasher. To do this, you need to access the settings menu. Please see the “Settings” section for detailed instructions on how to activate this feature.

To temporarily deactivate the button lock when you want to start the dishwasher, press the High temperature and Long dry buttons simultaneously. The button lock is automatically reactivated after 2 minutes.

The overflow protection function on your ASKO D5536XXLFISOF starts pumping out the machine and turns off the water supply if the water level in the dishwasher exceeds the normal level. If the overflow protection is triggered, turn off the water supply and call the Customer Care Center.

Before the first wash, you need to prepare the water softener by adding special dishwasher salt and filling the rinse aid dispenser.

To fill the salt compartment:

1. Unscrew the lid of the salt compartment.

2. Insert the supplied funnel. For the very first time, pour in about 0.3 gal (1 liter) of water.

3. Add large grain or special dishwasher salt until the compartment is full (maximum of 3 lb or 1.5 kg).

4. Wipe away any excess salt so the lid can be screwed on firmly.

5. Run a program to ensure any salt in the dishwasher is rinsed away. The salt indicator on the display will light up when it’s time to refill.

To fill the rinse aid dispenser:

1. Open the rinse aid compartment lid.

2. Carefully add rinse aid up to the level marked “max”.

3. Wipe up any spilled rinse aid around the compartment.

4. Close the lid firmly. The rinse aid indicator on the display will light up when it’s time to refill.

To save energy and water with your ASKO D5536XXLFISOF, follow these tips:

• Run programs only with a full load: Wait until the dishwasher is fully loaded before running a program. Use the Rinse & Hold program for unpleasant odors if needed while waiting.

• Run programs at a lower temperature: If dishes are only lightly soiled, select a program with a lower temperature.

• Select a program with the Short dry option: This saves energy. For better drying, leave the door slightly open after the program finishes.

• Do not rinse under running water: Simply scrape off large food particles before loading.

• Choose a green detergent: Read the environmental declaration on the packaging.

• Connect to cold water: If you use oil or electricity to heat your home.

• Connect to hot water (max. 160 °F / 70 °C): If you use district heating, solar power, or geothermal power. This cuts program times and reduces electricity consumption.

Some cookware is not dishwasher safe. Pay special attention to the following:

• Fragile decoration: Porcelain with decoration on top of the glazing should not be washed in a dishwasher.

• Crystal/Glass: Position items so they do not touch. Use a short program with the lowest possible wash temperature and select Short dry. A gray film can develop on glass washed at high temperatures.

• Silver: Silver and stainless steel items should not come into contact, as the silver can become discolored.

• Cutlery with glued handles: Some glues are not dishwasher safe and the handles may loosen.

• Wood: Only wash wooden items if they are marked dishwasher safe.

• Aluminum: Aluminum can lose its shine. Good quality aluminum pans can be washed, though some shine may be lost.

• Plastic items: Avoid washing plastic items that cannot withstand high temperatures.

Properly loading your ASKO D5536XXLFISOF ensures the best cleaning results.

• Top Cutlery Tray: Accommodates cutlery, ladles, whisks, and other utensils. This tray can be raised or lowered. To raise it, remove the tray and pull the two locking handles forward. To lower it, remove the tray and slide the two locking handles down and back.

• Upper Basket: Place glasses, cups, bowls, side plates, and saucers here. Place all soiled surfaces facing down. Wine glasses can be placed on the wine shelf.

• Lower Basket: Place plates, side plates, serving dishes, pots, and cutlery (in the cutlery basket) in this basket. For the best results on pots and pans, place them in the right rear of the lower basket to utilize the Power Zone™ Pot & Pans spray nozzles.

• Cutlery Basket: Place cutlery with handles facing down (except for knives) and spread them out. Ensure spoons do not stack. The basket is best placed in the middle at the front of the lower basket to utilize the Power Zone™ Cutlery spray nozzle.

Important: Knives and other pointed items must be placed with the points down in the cutlery basket or horizontally in other baskets. Also, always check that the spray arms can rotate freely after loading.

Your ASKO D5536XXLFISOF dishwasher has two detergent compartments: a small one for prewash (1) and a large one for the main wash (2).

Use only unscented, granular automatic dishwashing detergent. The amount needed depends on water hardness. Refer to the table for recommended amounts:

Water hardness	Detergent amounts
Soft (0-3 grains per gallon)	Prewash 1 teaspoon Main wash 1 to 1-1/2 tablespoons
Medium (4-8 grains per gallon)	Prewash 1 teaspoon Main wash 1 to 2 tablespoons
Hard (9+ grains*)	Prewash 1 teaspoon Main wash 2 to 3 tablespoons

*12 grains and higher is extremely hard water.

Dishwasher Tablets: If a tablet is difficult to fit, you can halve it. Tablets are not recommended for short programs (less than 75 minutes).

3-in-1/All-in-one Detergent: If you use these, activate the “TAB” setting in the settings menu. The salt compartment must still be filled with salt.

To operate your ASKO D5536XXLFISOF:

1. Turn on the dishwasher: Press and hold the On/Left-on mode button until the display lights up.

2. Select a program: Press the Program selector button one or more times until the desired program symbol appears on the display. Available programs include Sanitation, Normal, Heavy, Quick, Hygiene, Delicate, Eco, Upper half, Lower half, and Rinse & Hold.

3. Select options (optional): After choosing a program, you can select additional options:

• High temperature: Press this button to use a higher temperature for the main wash for improved results.

• Long dry: Press this button to increase the final rinse temperature and dry time for better drying. This option can be used with all programs except Rinse & Hold.

• Delayed start: Press this button repeatedly to delay the start from 1 to 24 hours.

4. Start the dishwasher: Press and hold the Start/Stop button until the display shows the door open symbol. Close the door properly to start the program.

Yes, you can interact with the ASKO D5536XXLFISOF after a cycle has started.

• Stopping or changing a program: If you want to change the program, open the door, then press and hold the Start/Stop button for three seconds. If the detergent dispenser lid has already opened, you should add more detergent. Then, choose a new program, press Start/Stop, and close the door.

• Adding more dishes: Open the door. The dishwasher will stop automatically. Add the dishes, close the door, and the dishwasher will resume the program.

To open the settings menu on your ASKO D5536XXLFISOF, follow these steps:

1. First, open the door. Turn off the dishwasher using the On/Left-on mode button (press and hold).

2. Press and hold the On/Left-on mode button again until the display lights up.

3. Within five seconds, press and hold the Program selector (PROG) and the Long dry (SSS) buttons simultaneously.

4. Release the buttons when the display shows “SET”.

Once in the settings menu, you can navigate and adjust the following:

• Use the PROG button to browse between setting values (e.g., from level 1 to level 2).

• Press the Start/Stop button to save the current setting value and move to the next setting category.

Keep pressing Start/Stop to step through and save each setting, or to exit the settings menu.

On your ASKO D5536XXLFISOF, you can customize the following settings:

• Child lock (Kid Safe™): Can be set to On or Off to prevent children from starting the dishwasher.

• Buzzer volume: Adjusts the volume of the buzzer that indicates when a program is finished or a fault has occurred. Settings are 0 (Off) to 4 (High).

• Operation volume: Adjusts the confirmation sound for each button press. Settings are 0 (Off) to 4 (High).

• LCD contrast: Adjusts the contrast of the display panel. Settings are -1 (Low) to 3 (High).

• Rinse aid: Sets the rinse aid dosage. Settings are 0 (Off) to 6 (High dosage). The factory setting is 5.

• TAB (3-in-1/all-in-one detergent): Set to On when using combination detergents. This adapts the program for best results.

• Water hardness: Adjusts the built-in water softener based on your local water hardness. See the water hardness table for the correct setting.

To achieve good dishwashing results, you must adjust the water softener setting on your ASKO D5536XXLFISOF to match the hardness of your water supply. Access the settings menu, navigate to the “Water hardness” setting, and select the appropriate level based on the table below. Contact your local water utility to find out the water hardness in your area.

°dH (German scale)	°fH (French scale)	Setting on Dishwasher
0-5	0-9	8:0
6-8	10-14	8:1
9-11	15-20	8:2
12-14	21-25	8:3
15-19	26-34	8:4
20-24	35-43	8:5
25-29	44-52	8:6
30-39	53-70	8:7
40-49	71-88	8:8
50+	89+	8:9

The filters in your ASKO D5536XXLFISOF should be cleaned regularly. The dishwasher must not be used without the filters in place.

Cleaning the Coarse Filter:

1. Lift the coarse filter by its handle.

2. Empty the filter of any large food particles and rinse it. Remember to replace it.

Cleaning the Fine Filter:

1. Turn the handle on the filter assembly counterclockwise once.

2. Lift the pipe section straight up by the handle. Free the coarse filter to clean the pipe section.

3. Remove and clean the fine filter.

4. Replace in reverse order, ensuring the edges seal properly.

5. Lock the filter back in place by turning the handle clockwise to its stop position. The handle should point straight out from the dishwasher.

If you suspect the drain pump is blocked, you can access it from inside the ASKO D5536XXLFISOF dishwasher.

1. Cut the power to the dishwasher by unplugging it from the power outlet.

2. Remove the coarse filter and pipe section.

3. Remove the small yellow drain pump access cover located at the left of the bottom drain.

4. By inserting your finger into the hole, you can turn the pump blades to release anything that might be blocking the pump.

5. Reinstall the access cover and the filters.

6. Plug the machine back in. Do not forget to reinstall the drain pump access cover.

Holes and bearings in the spray arms can become blocked. Use a needle or similar item to remove debris. The spray arms can be removed for more thorough cleaning.

• Lower spray arm: Pull the lower spray arm straight up to release it.

• Upper spray arm: The upper basket must be removed first. Extend the upper basket, rotate each basket catch runner outward, and remove the basket. Then, pull the upper spray arm straight up to release it.

• Top spray arm: After removing the upper basket, remove the top cutlery tray. Push the top spray arm up and turn its bearings counterclockwise to remove the spray arm.

After cleaning, reinstall all parts securely.

The tub of your ASKO D5536XXLFISOF is made of stainless steel and is kept clean through normal use. However, if you have hard water, limescale deposits may form. If this happens, run the Normal program with high temperature and two tablespoons of citric acid or a commercially available dishwasher cleaner in the detergent compartment (with no dishes in the machine).

If your ASKO D5536XXLFISOF displays an error code, refer to the following actions:

• F:10 Overfilling: Call the Customer Care Center.

• F:11 Water outlet fault: See troubleshooting for “Water remains in the dishwasher above the filters”.

• F:12 Water inlet fault: Check that the water supply valve is on.

• F:40 Inlet valve leakage: Turn off the water supply valve and call the Customer Care Center.

To clear the error message from the display, turn the machine off with the On/Left-on mode button and then turn it on again.

If your dishes are not clean after a wash cycle in your ASKO D5536XXLFISOF, check for these possible causes:

• The spray arms do not rotate: Check that the dishes are not blocking the spray arms. Remove and clean the arms if they are clogged.

• Detergent is too old: Detergent is a perishable product. Avoid buying large packages.

• Incorrect detergent dosage: Dose according to water hardness. Too much or too little can result in poor washing.

• Dishwashing program is too weak: Select a higher temperature or a more powerful program.

• Dishes are loaded incorrectly: Do not cover dishes with large bowls or lids. Avoid placing very tall glasses in the corners of the baskets.

• The filter is not correctly fitted: Screw the filter firmly into place as per the maintenance instructions.

Spots or films on dishes from your ASKO D5536XXLFISOF can be caused by several issues:

• Sticky white/blue film: The rinse aid dosage setting is too high. Reduce the amount in the settings. If you have very soft water, you may want to dilute the rinse aid 50:50 with water.

• General spots or films:

– Incorrect water softener setting: See the section on Settings to adjust it.

– Incorrect rinse aid dosage setting: Adjust the dosage in Settings.

– Salt compartment is empty: Top up with dishwasher salt.

– Leaking salt: Check that the salt compartment lid is properly tightened.

– Using 3-in-1 detergent with the TAB setting activated: Deactivate the TAB setting and top up with regular salt and rinse aid.

– Etching on crystal: Too high a temperature and/or too much detergent can cause etching. This cannot be repaired. Wash crystal at a low temperature with a conservative amount of detergent.

If your ASKO D5536XXLFISOF dishwasher fails to start, check the following:

• Start/Stop button: The button may have been pressed for too short a time. Press and hold Start/Stop until the display shows the door open symbol, then close the door.

• Door is not properly closed: Ensure the door is securely latched.

• Fuse/circuit breaker: Check if a fuse has blown or a circuit breaker has been tripped.

• Power plug: Make sure the dishwasher is plugged into the power outlet.

• Water supply valve: Check that the water supply valve is turned on.

• Delayed start option: Check that the Delayed start option has not been selected. To cancel it, press and hold Start/Stop for three seconds.

If water remains in your ASKO D5536XXLFISOF dishwasher above the filters, it could be due to a blockage:

• Blocked drain hose: Loosen the drain hose from where it terminates and check that no debris has clogged it.

• Kink in drain hose: Check that the hose is free from kinks and sharp bends.

• The filters are blocked: Clean the coarse and fine filters.

• Debris in the drain pump: Clean the drain pump following the instructions in the Care and Maintenance section.

If your dishes are not dry enough, consider the following solutions for your ASKO D5536XXLFISOF:

• Drying power is too low: Activate the Long dry option for better drying performance.

• The dishwasher is not fully loaded: A full load dries more effectively. Fully load the dishwasher.

• Rinse aid issues: The rinse aid may need topping up, or the dosage is set too low. Refill the rinse aid or increase the dosage in the settings.

• 3-in-1 detergent is used with TAB setting activated: This can affect drying. Inactivate the setting TAB and top up with salt and rinse aid.

• Door remains closed: For better results, open the door slightly once the program has finished.

The technical data for the ASKO D5536XXLFISOF dishwasher is as follows:

• Height: 33-7/8″ – 35-7/8″ (860-912 mm)

• Width: 23-5/8″ (600 mm)

• Depth: 22-7/8″ (581 mm)

• Weight: 117 lb (53 kg) (Weight can vary due to different specifications)

• Water pressure: 4.2-140 psi

• Electrical connection: See serial number tag and rating plate.

• Rated power: See serial number tag and rating plate.

The following table shows the program details for the ASKO D5536XXLFISOF, including consumption values which can vary.

Program	Options	Prewashes	Main wash (°F)	Number of rinses	Final rinse temperature (°F)	Consumption values (Cold water)		Consumption values (Hot water)		Water consumption (gallon)
						Dishwashing time (approx. hrs:min)	Energy (approx. kWh)	Dishwashing time (approx. hrs:min)	Energy (approx. kWh)
Sanitation		2	150 °F	2	150 °F	3:15	1.5	3:00	0.9	4.7
Normal		1	124 °F	2	117 °F	2:20	0.8	2:00	0.4	3.8
Heavy		2	140 °F	2	150 °F	2:25	1.3	2:10	0.7	3.2
Quick			85 °F	2	85 °F	0:20	0.2	0:20	0.1	2.6
Hyg Hygiene			160 °F	2	160 °F	1:20	1.5	0:50	0.9	2.6
Delicate		1	105 °F	2	120 °F	1:50	0.9	1:35	0.5	3.7
Eco Eco			130 °F	2	120 °F	2:30	0.8	2:15	0.5	2.9
Upper half		1	130 °F	2	140 °F	2:25	1.2	2:05	0.6	3.7
Lower half		1	130 °F	2	140 °F	2:25	1.2	2:05	0.6	3.7
Rinse & Hold				1	— °F	0:06	0.01	0:06	0.01	0.8

Certainly. Here is a quick guide for your ASKO D5536XXLFISOF dishwasher:

1. Load the baskets: Scrape off large food particles before loading. Do not rinse dishes under running water.

2. Check spray arms: Make sure the spray arms can rotate freely. Also check that the water supply valve is on.

3. Add detergent: Use the small compartment for prewash and the large one for the main wash.

4. Power on: Press and hold the On/Left-on button until the display illuminates.

5. Check rinse aid and salt: To improve results, ensure the rinse aid and salt dispensers are filled. The indicators will light up when they are low.

6. Select a program and options: Press the PROG button to choose a wash cycle and select any desired options.

7. Start: Press and hold Start/Stop, then close the door to begin the wash.