VOX ELECTRONICS TM-6002 (02) PDF Document

When using the VOX ELECTRONICS TM-6002, basic safety precautions should always be followed:

1. Read all instructions.

2. Before using, check that the voltage indicated on the product corresponds with the voltage of your electrical outlet.

3. Do not let the cord hang on a hot surface or over the edge of a table or counter.

4. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair, or adjustment.

5. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

6. Close supervision is necessary when any appliance is used by or near children.

7. Avoid contacting the moving parts.

8. Keep hands and utensils out of the container while blending to reduce the risk of severe injury to persons or damage to the blender. A scraper may be used but must be used only when the blender is not running.

9. The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock, or injury.

10. Unplug from the outlet when not in use, before putting on or taking off parts, and before cleaning. To disconnect, turn any control to “off”, then remove the plug from the wall outlet by grasping the plug, not the cord.

11. To reduce the risk of injury, never place the blade assembly on the motor unit without the jar properly attached.

12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliances by a person responsible for their safety.

13. Children should be supervised to ensure that they do not play with the appliance.

14. Do not leave the machine on unattended.

15. When removing the blender from the motor unit, wait until the blades have completely stopped.

16. Always operate the blender with the cover in place.

17. Always use the appliance on a secure, dry level surface.

18. Never place this appliance on or near a hot gas or an electric burner or where it could touch a heated appliance.

19. Do not use outdoors.

20. Do not use the appliance for other than its intended use.

WARNING: Potential injury from misuse. Care shall be taken when handling the sharp cutting blades, emptying the bowl, and during cleaning.

CAUTION: Ensure that the blender is switched off before removing it from the stand. Switch off the appliance and disconnect from the supply before changing accessories or approaching parts that move in use.

The VOX ELECTRONICS TM-6002 stand mixer consists of the following parts:

– Measure cup

– Cover

– Jar

– Blade assembly

– Seal ring

– Blade base

– Motor unit

– Speed knob

Before initial use, unpack the appliance and place all parts on a horizontal surface. The jar assembly is pre-assembled, but you should disassemble it to wash all detachable parts (except the motor unit) before first use. Once cleaned and thoroughly dried, reassemble as follows:

1. Invert the jar onto a level surface, holding the jar handle. Place the seal ring 2 and blade assembly onto the jar base bottom and secure the blade assembly by turning it anti-clockwise until tight.

2. Reposition the jar assembly with its opening upwards. Wrap the seal ring 1 around the lid bottom and put the lid onto the jar assembly. Place the measure cup exactly into the lid by fitting the small projection on both sides of the cup into the slots of the lid and turning the cup clockwise until tight.

3. Finally, place the assembled jar onto the motor unit by aligning the strip on the assembled jar bottom.

CAUTION: The jar and jar base are now secure. Do not try to twist the jar and jar base onto the motor unit.

1. Peel or core the fruit or vegetables and then cut it into small dices.

2. Place the food to be blended into the jar. Usually, a certain amount of purified water has to be added to facilitate the smooth running of the appliance. The proportion of the food and water is 2:3. The amount of mixture should not exceed the max level as indicated on the jar. Note: never use boiling liquids or run the appliance empty.

3. Put the lid on the jar. Be sure the measuring cup is in place.

4. Plug the power cord into a standard wall outlet.

5. Turn the speed knob to the appropriate speed setting for your task.

6. For quick or delicate blending tasks, turn the speed knob to the P (Pulse) position and hold for a few seconds. When released, the knob will automatically reset to the O (Off) position. Operate several times until the desired consistency is obtained.

7. If you want to add ingredients while the blender is working, remove the measuring cup and place them through the lid opening.

8. When crushing ice or hard food, keep one hand firmly on the lid.

9. When the desired consistency is obtained, turn the knob to the O position.

Note: For each use, the consecutive operation time should not exceed 3 minutes. At least 10 minutes of rest time must be maintained between two continuous cycles. Let the unit cool to room temperature before performing the next operation cycle. If you want to stop the machine during operation, turn the knob to the O position at any time.

– For best circulation of food that is to be blended with some liquid, pour the liquid into the jar first, then add solids.

– Some of the tasks that cannot be performed efficiently with the VOX ELECTRONICS TM-6002 are: beating egg whites, whipping cream, mashing potatoes, grinding meat, mixing dough, and extracting juice from fruit and vegetables.

– The following items should never be placed in the unit as they may cause damage: bones, large pieces of solid, frozen food, or tough foods such as turnips.

– To crush ice, add up to 6 ice cubes. If more ice is needed, remove the cup and add cubes one by one through the lid opening.

This product contains no user-serviceable parts. Refer service to qualified service personnel.

1. Before cleaning, unplug the blender.

2. Always wash immediately after use for easier cleaning. Don’t let food dry on the jar assembly as this will make cleaning difficult.

3. For a quick clean, pour a little warm soapy water into the jar and turn the knob to the P position for a few seconds. Then empty the jar.

4. For a thorough clean, dismantle all detachable parts. Lift the jar assembly off the motor unit. To detach the blade assembly, turn it clockwise from the jar base bottom, and remove seal ring 2 and the blade assembly. In addition, detach the jar cover seal ring 1 from the jar cover.

5. Rinse the measure cup, lid, seal ring 1, jar, seal ring 2, and blade assembly by hand or in a dishwasher and then dry. They are dishwasher safe components, but the temperature setting shall not exceed 70°C.

6. Brush the blade clean using warm soapy water, then rinse thoroughly under the tap. Don’t touch the sharp blades; handle carefully. Don’t immerse the blade assembly in water. Leave to dry upside down away from children.

7. Wipe the motor unit with a damp cloth and dry thoroughly. Remove stubborn spots by rubbing with a non-abrasive cleaner. If liquids spill into the motor unit, first unplug the unit, then wipe with a damp cloth and dry thoroughly.

CAUTION:

1) Do not immerse the motor unit in liquid to prevent the risk of electric shock.

2) Do not use rough scouring pads or cleansers on parts or finish.

3) Do not place any parts of this unit into the dishwasher for cleaning. This unit is not available for the dishwasher.