VOX ELECTRONICS TM-6008 IM (01) PDF Document

When using the VOX ELECTRONICS TM-6008 IM, basic safety precautions should always be followed:

1. Read all instructions before use.

2. Check that the voltage indicated on the product corresponds with your electrical outlet voltage.

3. Do not let the cord hang over the edge of a table or counter, or touch a hot surface.

4. Do not operate with a damaged cord or plug, or after a malfunction. Return it to the nearest authorized service facility.

5. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.

6. Close supervision is necessary when used by or near children. Children should be supervised to ensure they do not play with the appliance.

7. Avoid contacting moving parts.

8. Keep hands and utensils out of the container while blending. A scraper may be used, but only when the blender is not running.

9. The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock, or injury.

10. Unplug from the outlet when not in use, before putting on or taking off parts, and before cleaning.

11. To reduce the risk of injury, never place the blade assembly on the motor unit without the jar properly attached.

12. This appliance is not for use by persons with reduced physical, sensory, or mental capabilities unless they have supervision.

13. Do not leave the machine unattended.

14. When removing the blender from the motor unit, wait until the blades have completely stopped.

15. Always operate the blender with the cover in place.

16. Always use the appliance on a secure, dry, level surface.

17. Never place this appliance on or near a hot gas or electric burner or where it could touch a heated appliance.

18. Do not use outdoors.

19. Do not use the appliance for anything other than its intended use.

WARNING: Potential injury from misuse. Care shall be taken when handling the sharp cutting blades, emptying the bowl, and during cleaning.

CAUTION: Ensure the blender is switched off before removing it from the stand. Switch off the appliance and disconnect from the supply before changing accessories or approaching parts that move in use.

The VOX ELECTRONICS TM-6008 IM consists of the following parts:

• Measure cup

• Cover

• Jar

• Blade asm (assembly)

• Seal ring

• Blade base

• Motor unit

• Speed knob

Before initial use, unpack the VOX ELECTRONICS TM-6008 IM and place all parts on a horizontal surface. The jar assembly is pre-assembled, but you should disassemble and wash all detachable parts except the motor unit first. Once all pieces are cleaned and thoroughly dry, reassemble as follows:

1. Invert the jar onto a level surface while holding the jar handle. Place seal ring 2 and the blade assembly onto the jar base bottom. Secure the blade assembly by turning it anti-clockwise until tight.

2. Reposition the jar assembly with its opening facing upwards. Wrap seal ring 1 around the lid bottom and put the lid onto the jar assembly. Place the measure cup into the lid by fitting the small projection on both sides of the cup into the slots of the lid, then turn the cup clockwise until tight.

3. Finally, place the assembled jar onto the motor unit by aligning the strip on the assembled jar bottom.

CAUTION: The jar and jar base are now secure. Do not try to twist the jar and jar base onto the motor unit.

1. Peel or core the fruit or vegetables and cut them into small dices.

2. Place the food to be blended into the jar. Usually, a certain amount of purified water should be added to help the appliance run smoothly. The recommended proportion of food to water is 2:3. The amount of the mixture should not exceed the max level indicated on the jar.

3. Put the lid on the jar and ensure the measuring cup is in place.

4. Plug the power cord into a standard wall outlet.

5. Turn the speed knob to the appropriate speed setting for your task.

6. For quick or delicate blending tasks, turn the speed knob to the P (Pulse) position and hold for a few seconds. When released, the knob will automatically reset to the O (Off) position. Repeat this several times until you obtain the desired consistency.

7. To add ingredients while the blender is working, remove the measuring cup and place them through the lid opening.

8. When crushing ice or hard food, keep one hand firmly on the lid.

9. When you have obtained the desired consistency, turn the knob to the O position to stop the blender.

Note: For each use, the consecutive operation time should not exceed 3 minutes. At least 10 minutes of rest time must be maintained between two continuous cycles. Let the unit cool to room temperature before starting the next operation cycle.

Yes, here is a sample recipe for the VOX ELECTRONICS TM-6008 IM:

Note: Never use boiling liquids or run the appliance empty.

• For the best circulation of food, especially when blending with liquid, pour the liquid into the jar first, then add the solids.

• Some tasks that cannot be performed efficiently with a blender are: beating egg whites, whipping cream, mashing potatoes, grinding meat, mixing dough, and extracting juice from fruit and vegetables.

• The following items should never be placed in the unit as they may cause damage: bones, large pieces of solid frozen food, or tough foods such as turnips.

• To crush ice, add up to 6 ice cubes. If more ice is needed, remove the measuring cup and add cubes one by one through the lid opening.

This product contains no user-serviceable parts. Refer service to qualified service personnel.

1. Before cleaning, unplug the blender.

2. Always wash immediately after use for easier cleaning. Don’t let food dry on the jar assembly, as this will make cleaning difficult.

3. For a quick clean, pour a little warm soapy water into the jar, turn the knob to the P (Pulse) position for a few seconds, and then empty the jar.

4. For a thorough clean, dismantle all detachable parts. Lift the jar assembly off the motor unit. To detach the blade assembly, turn it clockwise from the jar base bottom, and remove seal ring 2 and the blade assembly. Also, detach seal ring 1 from the jar cover.

5. Rinse the measure cup, lid, seal ring 1, jar, seal ring 2, and blade assembly by hand or in a dishwasher. These components are dishwasher safe, but the temperature setting should not exceed 70°C.

6. Brush the blade clean using warm soapy water, then rinse thoroughly under the tap. Handle carefully and do not touch the sharp blades. Do not immerse the blade assembly in water. Leave it to dry upside down, away from children.

7. Wipe the motor unit with a damp cloth and dry thoroughly. Remove stubborn spots by rubbing with a non-abrasive cleaner. If liquids spill into the motor unit, first unplug it, then wipe with a damp cloth and dry thoroughly.

Please observe the following cautions during cleaning:

1. Do not immerse the motor unit in liquid to prevent the risk of electric shock.

2. Do not use rough scouring pads or cleansers on parts or the finish.

3. Do not place any parts of this unit into the dishwasher for cleaning. The unit is not available for the dishwasher.