VOX ELECTRONICS TM-6006 (02) PDF Document

When using the VOX ELECTRONICS TM-6006, you should always follow basic safety precautions, including:

1. Read all instructions before use.

2. Ensure the voltage on the blender corresponds with your electrical outlet voltage.

3. Do not let the cord hang over the edge of a table or counter, or touch a hot surface.

4. Do not operate the appliance if it has a damaged cord or plug, or if it malfunctions or has been damaged. Return it to the nearest authorized service facility.

5. If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.

6. Close supervision is necessary when the appliance is used by or near children. Children should be supervised to ensure they do not play with the appliance.

7. Avoid contact with moving parts.

8. Keep hands and utensils out of the container while blending to reduce the risk of injury. A scraper may be used, but only when the blender is not running.

9. The use of attachments not recommended or sold by the manufacturer may cause fire, electric shock, or injury.

10. Unplug the blender from the outlet when not in use, before putting on or taking off parts, and before cleaning.

11. Never place the blade assembly on the motor unit without the jar properly attached.

12. Do not leave the machine unattended while it is operating.

13. When removing the blender from the motor unit, wait until the blades have completely stopped.

14. Always operate the blender with the cover in place.

15. Always use the appliance on a secure, dry, level surface.

16. Never place this appliance on or near a hot gas or electric burner or where it could touch a heated appliance.

17. Do not use the appliance outdoors.

18. Do not use the appliance for anything other than its intended use.

19. Be careful when handling the sharp cutting blades, emptying the bowl, and during cleaning to avoid potential injury from misuse.

20. Ensure the blender is switched off before removing the jar from the stand. Switch off the appliance and disconnect it from the power supply before changing accessories or approaching parts that move in use.

The VOX ELECTRONICS TM-6006 stand blender consists of the following parts:

• Measure cup

• Cover

• Jar

• Blade assembly

• Seal ring

• Blade base

• Motor unit

• Speed knob

Before initial use, unpack the VOX ELECTRONICS TM-6006 and place all parts on a horizontal surface. The jar assembly is already assembled in the motor unit, but you should disassemble it to wash all detachable parts (except the motor unit) before the first use. Once all pieces are cleaned and thoroughly dried, reassemble as follows:

1. Invert the jar onto a level surface while holding the jar handle. Place seal ring 2 and the blade assembly onto the jar base bottom.

2. Secure the blade assembly by turning it anti-clockwise until it is tight.

3. Reposition the jar so its opening is facing upwards. Wrap seal ring 1 around the bottom of the lid and place the lid onto the jar assembly.

4. Place the measure cup into the lid by fitting the small projections on the cup into the slots of the lid. Turn the cup clockwise until tight.

5. Finally, place the assembled jar onto the motor unit by aligning the strip on the bottom of the assembled jar. The jar and jar base are now secure. Do not try to twist the jar and jar base onto the motor unit.

1. Prepare your food by peeling or coring fruits or vegetables and cutting them into small dice.

2. Place the food into the jar. To facilitate smooth operation, it is usually necessary to add a certain amount of purified water. The recommended proportion of food to water is 2:3. The amount of the mixture should not exceed the max level indicated on the jar. Note: Never use boiling liquids or run the appliance empty.

3. Put the lid on the jar and ensure the measuring cup is securely in place.

4. Plug the power cord into a standard wall outlet.

5. Turn the speed knob to the appropriate speed setting for your task (1 or 2).

6. For quick or delicate blending, turn the speed knob to the P (Pulse) position and hold it for a few seconds. When you release it, the knob will automatically reset to the O (Off) position. Repeat this action several times until you achieve the desired consistency.

7. If you want to add ingredients while the blender is working, remove the measuring cup and place them through the opening in the lid.

8. When crushing ice or hard food, keep one hand firmly on the lid for stability.

9. When you have obtained the desired consistency, turn the knob to the O position to stop the blender.

Important Note on Operation Time: For each use, the consecutive operation time should not exceed 3 minutes. A rest time of at least 10 minutes must be maintained between two continuous cycles. Allow the unit to cool to room temperature before performing the next operation cycle. You can stop the machine at any time during operation by turning the knob to the O position.

Here is a sample recipe provided for the VOX ELECTRONICS TM-6006:

• For the best circulation of food that is to be blended with liquid, pour the liquid into the jar first, then add the solid ingredients.

• To crush ice, add up to 6 ice cubes. If more ice is needed, remove the measuring cup and add cubes one by one through the lid opening.

• Some tasks that cannot be performed efficiently with the blender are: beating egg whites, whipping cream, mashing potatoes, grinding meat, mixing dough, and extracting juice from fruit and vegetables.

• To avoid damage, the following items should never be placed in the unit: bones, large pieces of solid frozen food, or tough foods such as turnips.

This product contains no user-serviceable parts. For service, refer to qualified service personnel.

1. Before cleaning, always unplug the blender.

2. For easier cleaning, wash the blender immediately after use. Do not let food dry on the jar assembly, as this will make cleaning difficult.

3. For a quick clean, pour a little warm soapy water into the jar, turn the knob to the P (Pulse) position for a few seconds, and then empty the jar.

4. To deep clean, dismantle all detachable parts. Lift the jar assembly off the motor unit. Detach the blade assembly by turning it clockwise from the jar base bottom. Then, remove seal ring 2 and the blade assembly. Also, detach seal ring 1 from the jar cover.

5. Rinse the measure cup, lid, seal ring 1, jar, seal ring 2, and blade assembly by hand or in a dishwasher. According to the manual, these parts are dishwasher safe, but the temperature setting should not exceed 70°C.

6. Brush the blade clean using warm soapy water, then rinse thoroughly under the tap. Handle the sharp blades with care and do not touch them directly. Do not immerse the blade assembly in water. Let it dry upside down, away from children.

7. Wipe the motor unit with a damp cloth and dry it thoroughly. Remove stubborn spots by rubbing with a non-abrasive cleaner. If liquids spill into the motor unit, first unplug it, then wipe with a damp cloth and dry thoroughly.

CAUTION:

• Do not immerse the motor unit in liquid to prevent the risk of electric shock.

• Do not use rough scouring pads or cleansers on any parts or the finish.

• The PDF contains conflicting information regarding dishwasher use. While one section states the detachable components are dishwasher safe up to 70°C, a caution section states, “Do not place any parts of this unit into dishwasher for cleaning. This unit is not available for dishwasher.” Please use your discretion or wash parts by hand to be safe.