CECOTEC BOLERO FLUX DM 906500 GLASS BLACK A (01) PDF Document

The buttons for the CECOTEC BOLERO FLUX DM 906500 GLASS BLACK A are as follows:

1. Off button

2. Eco button (low speed)

3. II button (medium speed)

4. III button (high speed)

5. Light button

This appliance is packaged to protect it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place to prevent damage to the device when transporting it in the future. If the original packaging is disposed of, make sure all packaging materials are recycled accordingly.

Ensure that all parts and components are included and in good condition. The box should contain:

• Kitchen hood

• Assembly kit (depending on model)

• Instruction manual

Before installing the CECOTEC BOLERO FLUX DM 906500 GLASS BLACK A, please note the following:

• Make sure the area is clean to prevent it from sucking in dust or dirt.

• The kitchen hood must not share the same ventilation duct with other appliances that use gas or other fuels.

• To facilitate air outlet, the ventilation duct should have a curvature of ≥120° and be connected to the outside wall.

• After installation, ensure that the kitchen hood is level to prevent grease build-up on the end.

• The kitchen hood should be placed at a distance of 65-75 cm above the cooking surface for the best effect.

Follow these steps to install your CECOTEC BOLERO FLUX DM 906500 GLASS BLACK A:

1. Install the wall hook in a suitable location once the installation height is set and keep it aligned. Use screws to fix it to the wall. The screws used for the chimney bracket are ST4*40 mm star head screws.

2. Fix the outer bracket on the chimney, and make sure that the inner part of the chimney can be adjusted to the installation height, as well as that of the exhaust duct. Then, install the exhaust duct in the chimney of the kitchen hood and place the hood in the bracket.

3. Place the kitchen hood on the hook on the wall.

4. Fix the outer bracket with the hooks and the inner part of the chimney with two screws (ST4*8 mm). Fix the housing with safety screws (ST4*30 mm).

5. Plug the power cable into the outlet.

6. Connect the wiring. You must connect the phase and neutral cables to a 220-240 V~/ 50 Hz power cable. The kitchen hood must be connected to an earthed installation. There are two safety ventilation ducts in the back housing.

• Black cable (or brown, depending on models) > Phase

• Blue cable > neutral

• Yellow-Green cable > ground

You can adjust the speed of the CECOTEC BOLERO FLUX DM 906500 GLASS BLACK A using the buttons:

1. Press the power button, the motor will stop.

2. Press the Eco button, the kitchen hood will beep, and the motor will operate at low speed.

3. Press the II button, the kitchen hood will beep, and the motor will operate at medium speed.

4. Press the III button, the kitchen hood will beep, and the motor will operate at high speed.

5. Press the light button so that it switches on. Press it again for the light to switch off.

NOTE: The hoods are equipped with an overheating protection system that acts to prevent possible incidents when the motor temperature exceeds the operating limit value.

Always disconnect the power supply before carrying out any cleaning or maintenance work on the kitchen hood. The cleaning and maintenance frequency depends on the use frequency and intensity.

1. To prevent the outer surface of the kitchen hood from deteriorating over time, it is recommended that it be cleaned with hot water and a non-corrosive detergent every two months.

2. Do not use abrasive detergents. Otherwise, the surface of the kitchen hood may be damaged.

3. Keep the motor and other parts away from water, as water may damage the appliance.

Do not use corrosive detergents to clean grease from the aluminium filters. Regular cleaning of the aluminium filters will prolong the life of the appliance and keep it in good working order. Follow the instructions below:

• Cleaning method 1: immerse the aluminium filters in hot water (40-50 °C), add neutral detergent and let them soak for 2 to 3 minutes. Protect yourself with gloves and clean the filters with a soft brush or scouring pad. Do not apply too much force, as filters are very delicate and can be easily damaged.

• Cleaning method 2: if you wish, you can also wash the filters in the dishwasher at a temperature of approx. 60 °C.

Note: to remove the filter, press on the tabs and pull it out.

The carbon filter has activated carbon which purifies air and absorbs cooking odours. The activated carbon becomes saturated after a period of time, which will reduce the adsorption capacity of the filter. The carbon filter cannot be washed nor cleaned in any way. When its service life comes to an end you must replace it with a new one.

• It is recommended to check the condition of carbon filters regularly, at least two or three times a year. Its replacement will depend on how the kitchen hood is used, as well as the daily operating time.

• In case of very frequent frying, shorten the time interval for checking and/or replacing the carbon filters.

1. Remove the protective metal filters.

2. The carbon filters are located on both sides of the motor. Insert and turn the filters, until they are firmly in place.

3. To replace the carbon filters, proceed in reverse order.

4. Carbon filters must not be exposed to heat.

The carbon filter dimensions for the CECOTEC BOLERO FLUX DM 906500 GLASS BLACK A are Ø176*35 mm.

Please note:

• Always disconnect the power supply before performing any operation on the appliance. When handling the bulb, make sure that it has cooled down completely before any direct contact with your hands.

• When handling the bulbs, hold them with a cloth or gloves to prevent sweat from coming into contact with the bulb, as this may reduce the bulb life.

Note:

• Before changing the light bulb, make sure that the appliance is switched off and unplugged.

• Protect yourself from danger when changing the light bulb, e.g. by wearing gloves.

If you are experiencing issues with your CECOTEC BOLERO FLUX DM 906500 GLASS BLACK A, refer to the troubleshooting table below.

If none of these situations match your problem, do not attempt to disassemble or repair the appliance by yourself. Repairs carried out by unqualified persons may result in injury or serious malfunctions.

Product reference: 02927

Rated voltage: 220-240 V

Rated frequency: 50 Hz

Total power: 168 W

Motor: 165 W

Light bulb: 2 x 1.5 W

650 m³/h air flow

Light type: Rectangular LED light

Lamp dimensions: 75×32 mm

ILCOS Code D: DBL-1.5-2-75/32

This appliance features a light source with an energy efficiency grade B.