SHARK HP070 (02) PDF Document

To reduce the risk of fire, electric shock, or injury, please adhere to the following general warnings:

1. This appliance has a polarized plug. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature. Unplug or disconnect the appliance from the power supply before servicing.

2. DO NOT operate any unit with a damaged cord or plug. Discard the unit or return to an authorized service facility.

3. DO NOT run cord under carpeting or cover it with throw rugs or similar coverings. Keep the cord away from high traffic areas.

4. If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons.

5. This appliance should only be placed on flat and dry surfaces.

6. This appliance is not intended for use by anyone (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have supervision.

7. Children should be supervised to ensure that they DO NOT play with the appliance.

8. Cleaning and user maintenance shall not be made by children without supervision.

9. Unplug the appliance from the electrical outlet prior to cleaning or maintenance.

10. DO NOT handle the plug or appliance with wet hands.

11. DO NOT use without the filter in place.

12. Only use Shark® branded filters and accessories.

13. DO NOT damage the power cord by pulling, carrying, or using it as a handle. Unplug by grasping the plug, not the cord. Avoid standing the appliance on the cord, closing a door on it, or leaving it near heated surfaces.

14. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.

15. DO NOT use if airflow is restricted. Turn the appliance off, unplug it, and remove all obstructions before turning it on again.

16. DO NOT use if the appliance is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.

17. DO NOT place the appliance on unstable surfaces such as chairs or tables.

18. DO NOT use in wet or damp surfaces, outdoor areas, or enclosed spaces with explosive or toxic fumes.

19. Turn off all controls before plugging in or unplugging.

20. Unplug from the electrical outlet when not in use and before any maintenance or cleaning.

21. Hand wash exterior hard plastic/non-electronic parts with water only. Do not immerse.

22. Make sure the filter is in place after routine maintenance.

23. Not suitable for use with solid-state speed controls.

24. The appliance is only to be used with the power supply unit provided.

The SHARK HP070 air purifier consists of the following parts:

1. Air Output Vents

2. Control Panel

3. Front Display

4. Air Purifier Body

5. Air Intake Vents

6. Mesh Dust Filter

7. HEPA Filter

8. HEPA Filter Door

• Make sure the front panel of the air purifier faces away from the closest wall.

• Do not move the unit while it is running. Turn off the power and unplug the air purifier before moving it.

• Make sure the air intake vents are not blocked.

• Do not place anything on the air purifier.

• Do not place the air purifier near heaters or radiators.

• Keep the air purifier out of direct sunlight and away from water or other liquid.

• Keep all nearby doors and windows closed when operating the air purifier.

• Avoid using in very humid environments.

1. DO NOT plug in the air purifier yet. First, carefully turn the air purifier upside down and place it on a level floor surface. Rotate the filter door counterclockwise to unlock it, then lift it off to access the HEPA filter.

2. Take the HEPA filter out of its plastic packaging. Reinstall the HEPA filter in either orientation.

3. With the HEPA filter reinstalled, rotate the filter door clockwise until it clicks into place.

4. Set up the air purifier on a level surface, at least 3 inches (8 cm) from walls and objects.

5. Carefully remove the yellow sticker on the front of the air purifier to access the display panel. Plug the air purifier into an electrical outlet and press the power button on the top control panel.

6. When the power is on, the air purifier will begin to analyze the air quality, indicated by rotating lights. After a few seconds, the air purifier will display the current air quality. If the air quality is between 96% to 100%, the number on the display will spin every five minutes to indicate that the machine is actively monitoring and cleaning the air.

On/Off: Press to turn the power on or off.

Fan Speed: Press repeatedly to cycle through the fan speed options: 1 Quiet, 2 Low, 3 Medium, 4 High, 5 Maximum, and A Auto. For optimal filter life and performance, select Auto mode. In Auto mode, the fan speed automatically adjusts based on air quality.

Air Info: Press to switch between air quality display options and filter life information.

Brightness: Adjusts the brightness of both the front display screen and the top control panel. Switch between 3 options: full brightness, partially dim, and fully dim.

Child Lock (Button Combination): Press and hold the Brightness and Fan Speed buttons at the same time for two seconds to lock the top control panel buttons. To unlock, press and hold both buttons again for two seconds.

Optimize Performance in Eco Mode: After 100% clean air status is achieved for 5 minutes in Auto Mode, your air purifier will enter Eco Mode to optimize the unit’s filter life.

Turn Off Beeping: To turn off notification sounds, press and hold the Air Info and Fan Speed buttons at the same time for two seconds. To resume, press and hold both buttons again.

The built-in sensor detects your air quality to give you real-time information. Use the AIR INFO button to switch between air quality display options.

The rings on the front display will change color as your air quality changes, allowing you to easily monitor your air quality even when the air purifier is across the room.

GOOD (85-100%): A blue ring means your air quality is good, with a low level of particle concentration.

FAIR (70-84%): An amber ring means your air quality is fair, with a moderate level of particle concentration. For better results, increase fan speed or select Auto Mode.

POOR (0-69%): A red ring means your air quality is poor, with a high level of particle concentration. For better results, increase fan speed or select Auto Mode.

Note: The air quality sensor uses a cumulative particle count across all particle sizes to determine percentage of clean air.

Your SHARK HP070 air purifier has 5 speed settings plus Auto Mode. Adjust fan speed to optimize your cleaning performance.

We recommend using this air purifier in Auto Mode. Auto Mode leverages your air purifier’s particle sensor, and this adjusts the fan speed automatically. Higher fan speeds work best for reducing odors and capturing debris most effectively.

We recommend setting up the air purifier in the room of your home where there is the most activity. This will help to clear the air of pollutants and odors as they are introduced. Note: This model is recommended for smaller rooms.

After 100% clean air is achieved for 5 minutes in Auto Mode, your air purifier will enter Eco Mode. The fan will turn off until a significant number of particles are detected, optimizing your HEPA filter’s life.

To turn off notification sounds, press and hold the Air Info and Fan Speed buttons at the same time for two seconds. To reactivate sounds, press and hold both buttons for 2 seconds again.

Your air purifier may have the child lock setting activated. Press and hold the Brightness and Fan Speed button for two seconds to turn this setting on or off.

If your air purifier displays a blue ring, your air quality is good. However, air quality will fluctuate as you introduce pollutants into your home. Activities like smoking, cooking, dusting, or spraying cleaning products can add pollutants to your air. The Clean Sense IQ™ technology tracks this fluctuation in real time and adjusts as it detects particles. To determine if the sensor is working correctly, spray perfume or aerosol cleaning product near the sensor on the back of the air purifier.

If your air quality never reaches 100%, make sure that the HEPA filter is properly installed and that its original plastic packaging has been removed. Activities like smoking, burning candles, running a humidifier, opening windows, and cooking can add more pollutants to your air. Make sure to survey your environment and remove anything that could be causing low air quality.

If the problem persists after these checks, the air quality sensor on the back of the air purifier may be dirty, causing a false reading. First, turn off and unplug the unit. Remove the mesh dust filter to locate the sensor on the back. Use a hand vacuum or hose attachment to clean the area around the sensor. After cleaning, wait 30 seconds before plugging the unit back in and turning it on. Let it run for 24 hours and monitor the air quality.

This easy-to-clean mesh dust filter captures large debris like hair, dust, and lint to protect the 3-layer HEPA filter. Maintenance is required on this filter when indicated on the front display.

When the mesh dust filter needs maintenance, the front display will show a pulsing red ring along with the text “check dust filter.”

To clean the filter, KEEP THE AIR PURIFIER PLUGGED IN and running, and complete the following steps:

1. LOCATE AND REMOVE MESH DUST FILTER: Gently slide up the filter and remove it. Check the screen for dust and debris buildup.

2. CLEAN DUST FILTER: Use a vacuum cleaner on low speed with a soft brush attachment OR a cloth/towel to remove debris from the mesh screen. DO NOT use abrasive chemical cleaners.

3. ADDITIONAL CLEANING (NOT REQUIRED): If additional cleaning is required, rinse the mesh dust filter with room temperature tap water. Be sure to completely dry the screen for 12 hours before reinstalling. DO NOT USE the air purifier when the mesh filter is wet.

4. REINSTALL MESH DUST FILTER: Gently reinsert the mesh dust filter into the slot on the side of the air purifier. Be sure to push the dust filter into place until it is flush with the air purifier body.

5. RECALIBRATION: Once the filter has been cleaned and reinstalled, the air purifier will recalibrate and begin to analyze air quality, indicated by the rotating lights.

To manually reset the Check Dust Filter indicator, press and hold the Air Info button on the top control panel for 1.5 seconds.

No, the HEPA filter is not washable. Keep the filter away from water and dispose of it when it is dirty.

NOTE: Unplug the air purifier whenever doing any cleaning or maintenance (other than checking the mesh dust filter).

For best results, clean the exterior every two months or as needed. Use a microfiber cloth to remove dust. To clean, wipe down the exterior with a microfiber cloth dampened with warm, soapy water. Avoid excess water and abrasive chemical cleaners to prevent damage.

NOTE: Unplug the air purifier whenever doing any cleaning or maintenance (other than checking the mesh dust filter).

For best results, clean the interior of the air purifier every two months or as needed. Remove the filter door, take out the HEPA filter, and use a vacuum cleaner or a microfiber cloth to remove dust and debris from the interior. DO NOT use abrasive chemical cleaners or water on the inside of the air purifier.

Shark NeverChange® Anti-Allergen True HEPA Filter

Captures 99.98%* of large, small, and micro-sized particles from the air and is equipped with 240 ± 10g virgin carbon for heightened protection against household odors.

*Based on IEST-RPCCO07.3, 0.1-0.2 microns.

Shark NeverChange PetPro filter

Captures 99.98%* of large, small, and micro-sized particles from the air and is equipped with 90 ± 10g virgin carbon for heightened protection against household odors. Contains 25% more carbon for odor absorption**.

*Based on IEST-RPCCO07.3, 0.1-0.2 microns.

**Compared to the Shark NeverChange Anti-Allergen True HEPA Filter.

Voltage: 24V DC / 0.8A

Watts: 16W