SHARK FLEXSTYLE HD400 (02) PDF DOCUMENT

When using the SHARK FLEXSTYLE HD400, especially when children are present, basic safety precautions should always be followed. The appliance is for household use only.

WARNINGS: KEEP AWAY FROM WATER

DANGER: As with most electrical appliances, electrical parts are electrically live even when the switch is off.

To reduce the risk of death by electric shock with your SHARK FLEXSTYLE HD400, follow these steps:

1. Always unplug the unit immediately after using.

2. Do not use while bathing.

3. Do not place or store the appliance where it can fall or be pulled into a tub or sink.

4. Do not place in or drop into water or other liquid.

5. If the appliance falls into water, unplug the unit immediately. Do not reach into the water.

To reduce the risk of burns, electrocution, fire, or injury to persons when using the SHARK FLEXSTYLE HD400:

1. The appliance should never be left unattended when plugged in.

2. Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.

3. Use this appliance only for its intended use. Do not use attachments not recommended by the manufacturer.

4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water.

5. Keep the cord away from heated surfaces.

6. Do not wrap the cord around the appliance.

7. Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.

8. Never use while sleeping.

9. Never drop or insert any object into any opening.

10. Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.

11. Do not use an extension cord with this appliance.

12. Do not direct hot air toward eyes or other heat-sensitive areas.

13. Attachments may be hot during use. Allow them to cool before handling.

14. Do not place the appliance on any surface while it is operating.

15. While using the appliance, keep your hair away from the air inlets.

16. Do not operate with a voltage converter.

1. Turn the styler on and off using the power button.

2. Adjust the airflow. Pressing the airflow button allows you to choose a low, medium, or high airflow.

3. Adjust the temperature. Pressing the temperature button allows you to choose no heat, low, medium, or high temperature.

4. Press and hold the Cool Shot button for a cool burst of air to set your style.

To attach an accessory: Press the accessory into the nozzle outlet. You will know it is properly attached when it clicks in place.

To remove an accessory: Slide the lock down and lift the accessory off of the nozzle by holding onto the touchpoints.

To change from styling wand mode to hair dryer mode: Slide down the lock and rotate the nozzle left. Keep rotating the nozzle until it clicks into place in hair dryer mode.

To change from hair dryer mode to styling wand mode: Slide down the lock and rotate the nozzle right.

Storage, Cord Safety, and Maintenance/Cleaning:

• Ensure the cord is not knotted, twisted, or wrapped around any nearby objects when in use.

• Store the unit in a dry location away from water and other heat sources.

• Regularly clean the filter at the bottom of the unit. To clean the filter, first slide the filter cover off the bottom of the unit. Then use a new toothbrush to brush off any dust or debris on the filter. Once the filter is clean, slide the filter cover back on the unit until it clicks in place.

A change in airflow or air power, airflow blockages, and/or visible buildup on the inlet at the bottom of the unit indicates your unit needs to be cleaned. It is recommended to use a new toothbrush to clean off the filter at the bottom of the unit.

The SHARK FLEXSTYLE HD400 is equipped with an Appliance Leakage Circuit Interrupter (ALCI), a safety feature that renders it inoperable under abnormal conditions. Should the dryer turn off in use, press the red Reset button on the plug and the dryer should function normally. If the dryer does not reset, please check your circuit breaker. If the issue persists, ensure there are no other appliances plugged in within the room where the dryer is being used. Do not use the dryer with a power strip.

This unit is equipped with a temperature-protective thermostat. If for some reason your hair dryer overheats, the thermostat will automatically turn the unit off. To prevent power-down recurrence, unplug the hair dryer and set it aside to cool, or cool down using the cool shot button during use. Overheating may result if the unit is powered on for a long duration, or can indicate a blockage or dust buildup. It is recommended to use a new toothbrush to clean off the filter at the bottom of the unit. If overheating continues to occur, discontinue use.

The technical specifications for the SHARK FLEXSTYLE HD400 are:

Voltage: 120V~, 60Hz

Power: 1300 Watts