SHARK NAVIGATOR SWIVEL PRO NV150 (01) PDF MANUAL

SHARK NAVIGATOR SWIVEL PRO NV150 (01) PDF SUMMARY:

What are the general warnings to consider before using the Shark Navigator Swivel Pro Complete Upright Vacuum?

Your vacuum cleaner may consist of a motorized nozzle, wand, hose, and/ or vacuum pod. This device contains electrical connections, electrical wiring, and moving parts that potentially present risk to the user. Use only identical replacement parts. Carefully observe and follow the instructions provided to avoid improper use of the appliance. DO NOT use the vacuum for any purpose other than those described in the manual. Before use, carefully inspect all parts for any damage. DO NOT use if any parts are damaged. The use of an extension cord is NOT recommended. This vacuum cleaner contains no serviceable parts.

---

Who can use this appliance?

This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance shall not be made by children. Keep the appliance and its cord out of reach of children. DO NOT allow the appliance to be used by children. DO NOT allow to be used as a toy. Close supervision is necessary when used near children.

---

What should I do before connecting or disconnecting any motorized nozzles or other accessories?

Always turn off the vacuum cleaner.

---

What should I avoid when handling the plug or vacuum cleaner?

DO NOT handle the plug or vacuum cleaner with wet hands.

---

Is it okay to use the vacuum without filters?

DO NOT use without filters in place.

---

Can I use filters and accessories that are not Shark branded?

Only use Shark® branded filters and accessories. Failure to do so will also void the warranty.

---

What should I not do with the power cord?

• DO NOT pull or carry the vacuum cleaner by the cord or use the cord as a handle.
• DO NOT unplug by pulling on the cord. Grasp the plug, not the cord.
• DO NOT run the vacuum cleaner over the power cord, close a door on the cord, pull the cord around sharp corners, or leave the cord near heated surfaces.

---

What should I not put into the nozzle or accessory openings?

DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.

---

What should I do if the nozzle or accessory airflow is restricted?

If the air paths or the motorized floor nozzle become blocked, turn the vacuum cleaner off and unplug from electrical outlet. Remove all obstructions before you plug in and turn on the unit again.

---

What should I keep away from the nozzle and all vacuum openings?

Keep nozzle and all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.

---

What should I do if the plug does not fit fully into the outlet?

Reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.

---

When should I not use the vacuum cleaner?

• If it has a damaged cord or plug.
• If the vacuum cleaner is not working as it should.
• If it has been dropped, damaged, left outdoors, or dropped into water.

---

What kind of surfaces should I use extra care when cleaning?

Use extra care when cleaning on stairs.

---

Should I leave the vacuum cleaner unattended while plugged in?

DO NOT leave the vacuum cleaner unattended while plugged in.

---

What should I do to avoid damaging carpet fibers?

When powered on, keep the vacuum cleaner moving over the carpet surface at all times.

---

Where should I not place the vacuum cleaner?

DO NOT place vacuum cleaner on unstable surfaces such as chairs or tables.

---

What should I do when taking a break from cleaning?

Your Shark® vacuum may not be designed to stand up on its own. When taking a break from cleaning, you may need to lean it against furniture or a wall, or lay it flat on the floor. Using the vacuum for an application where the unit lacks stability may result in personal injury.

---

What should I not use the vacuum to pick up?

• Liquids
• Large objects
• Hard or sharp objects (glass, nails, screws, or coins)
• Large quantities of dust (drywall dust, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection.
• Smoking or burning objects (hot coals, cigarette butts, or matches)
• Flammable or combustible materials (lighter fluid, gasoline, or kerosene)
• Toxic materials (chlorine bleach, ammonia, or drain cleaner)

---

Where should I not use the vacuum cleaner?

• Poorly lit areas
• Wet or damp surfaces
• Outdoor areas
• Spaces that are enclosed and may contain explosive or toxic fumes or vapors (lighter fluid, gasoline, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)

---

What should I do before plugging in or unplugging the vacuum?

Turn off all controls.

---

When should I unplug the vacuum from the electrical outlet?

Unplug from electrical outlet when not in use and before any maintenance or cleaning.

---

How should I wash the unit?

Hand wash with water only. Washing with cleaning chemicals could damage the unit.

---

What should I avoid during cleaning or routine maintenance?

During cleaning or routine maintenance, DO NOT cut anything other than hair, fibers, or string wrapped around the brushroll.

---

How long should I let the filters air-dry before replacing them in the vacuum?

Allow all filters to air-dry completely before replacing in the vacuum to prevent liquid from being drawn into electric parts.

---

What should I make sure of after routine maintenance?

Make sure the dust cup and all filters are in place.

---

What should I do with the power cord during storage, if provided?

If provided, secure the power cord around the two cord hooks during storage.

---

How do I assemble the vacuum?

1. Insert the Wand into the Pod.
2. Insert the Handle into the top of the wand.
3. Connect the Hose to the back of the pod.
4. Insert the C-clip into the back of the pod.
5. Insert the hose into the C-clip and the hose holder.
6. Store Accessories on the Tool Storage Posts.

For proper operation, ensure all parts are firmly clicked into place.

---

How do I access the power cord?

Rotate upper hook down and remove cord. Use cord holder on the side of wand to hold cord in place while vacuuming.

---

What are the cleaning modes?

To engage Brushroll, step on the floor nozzle and tilt the handle back firmly. Select surface setting:

• O Off
• I Hard Floor: For bare floors and area rugs. The brushrolls will spin slowly in this mode.
• II Carpet: For carpets. The brushrolls spin quickly in this mode.

---

How do I engage the brushrolls?

To engage the brushrolls, turn on the power, step on the floor nozzle, and tilt the handle back.

---

What does the brushroll indicator light mean?

• Solid Green: The brushroll is spinning and working as intended.
• Solid Red: There is a jam in the brushroll area. Turn off and unplug the vacuum and remove any blockages in the nozzle.
• Flashing Red: The motorized floor nozzle is overheating. Turn the vacuum off and wait a minimum of 60 minutes for the unit to cool down. See Troubleshooting section for more information.

---

How do I detach the wand from the pod?

Press the Wand Release button and pull up on the wand to detach it from the pod.

---

How do I detach the handle from the wand?

Press the Handle Release button and pull up on the handle to detach it from the wand.

---

How do I use accessories with the wand and handle?

Attach a cleaning accessory to handle or wand.

---

What does the suction control slider do?

The Suction Control Slider located on the handle allows you to adjust the suction depending on the floor type.

• MIN: to reduce suction and increase maneuverability on carpets.
• MAX: to increase suction on bare floors.

---

How do I remove the dust cup?

Slide up the release button on the dust cup handle. Tilt dust cup forward, then lift to remove. To reinstall, place the bottom of dust cup onto the pod and then tilt until it clicks into place.

---

How do I empty the dust cup?

Press the release button to open the bottom of the dust cup. To remove collected debris from the Lint Screen, press the top release button and lift the handle to open the dust cup. Gently brush lint screen to clean.

---

How often should I rinse the pre-motor filters?

Every Month. Remove Dust Cup, then lift out Filters.

---

How often should I rinse the HEPA filter?

Every year. Remove dust cup, tilt Filter Door and firmly pull it off. Press tab at top of HEPA Filter and pull out filter. To reinstall, insert HEPA filter into unit and replace the filter door.

---

How do I clean the filters?

Rinse filters with cold water only to prevent damage from cleaning chemicals. Allow all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electronic parts. DO NOT use soap when cleaning the filters. Empty the dust cup each time you vacuum and periodically during cleaning, when debris in the dust cup reaches the MAX fill line.

---

How often should I replace the pre-motor and post-motor filters?

The pre-motor filters should be replaced every 2.5 years. The post-motor filter should be replaced every 3 years.

---

How do I clean the brushroll?

Clean off any debris on the bristles. Using a coin, turn locks counterclockwise, then lift the cover to access the brushroll. If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught behind the brushroll. Clear away any dust, dirt, or blockages in Debris Intake. To close the cover, push down until it clicks into place. Close the locks by using a coin to turn them clockwise.

---

How do I check for blockages in the hose, wand, pod, and dust cup?

• Detach hose from vacuum pod, and check hose and opening on back of pod for blockages.
• Detach wand from pod and handle, and check both ends for blockages.
• Detach wand from pod, and check opening for blockages.
• Detach handle from wand and hose from the vacuum pod, and check openings for blockages.
• Detach dust cup from vacuum pod. Empty dust cup, remove debris from lint screen, and check for blockages.

---

What should I do if the vacuum is not picking up debris, has no suction, or has light suction?

• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the filters before reinstalling them.
• Dust cup may be full; empty dust cup.
• Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any blockages found.
• If any string, hair, or carpet fibers are wrapped around the brushroll, remove the floor nozzle cover and use scissors to carefully cut away debris. See Cleaning the Brushroll section for more information.

---

What should I do if the vacuum lifts area rugs?

• Make sure the Power/Surface switch is set to Hard Floor (setting I).
• Rotate the suction control slider to MIN.
• Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.

---

What should I do if the brushroll does not spin?

If the Brushroll Indicator Light turns red, immediately turn off and unplug the vacuum. Lay the unit down and turn over so the brushroll is facing up. Using a coin, turn the 3 locks on the bottom of the nozzle to access the brushroll. Remove any hair or blockages from the nozzle. Reinstall the brushroll cover and turn all 3 locks back to the locked position. With the power on, recline the handle, which will automatically turn on the brushroll.

---

What should I do if the vacuum turns off on its own or the indicator light flashes red?

If your vacuum overheats, the thermostat will automatically turn the suction motor off. Perform the following steps to restart:

1. Turn vacuum off and unplug it.
2. Empty dust cup and clean filters (see Emptying the Dust Cup and Cleaning and Replacing the Filters).
3. Check for blockages in hose, accessories, wand, nozzle, and inlet openings.
4. Allow the unit to cool for a minimum of 60 minutes.
5. Plug in vacuum and restart with the Power/Surface switch.

---

What accessories are available for the vacuum?

• Crevice Tool: This slender tool offers extended reach to access corners, baseboards, tight spaces, and ceilings.
• Duster Crevice Tool: Two cleaning tools in one. The crevice tool gives you extended reach to clean in tight spaces, while the soft brush is ideal for dusting delicate surfaces.
• Dusting Brush: This brush dusts and cleans delicate surfaces. Great for use on fans, blinds, lampshades, and keyboards.
• Upholstery Tool: Picks up hair, dust, and large debris from mattresses, couches, curtains, lampshades, and other delicate upholstered fabrics.
• Pet Multi-Tool: A single convertible tool for cleaning tough pet messes two ways: use the stiff bristle brush to clean stuck-on debris, or take off the bristles to reveal an upholstery tool perfect for removing stubborn pet hair and large piles of debris.
• Pet Power Brush: The turbine brush loosens and removes pet hair and debris from carpets, and powerfully deep-cleans dander out of upholstery and other surfaces.
• Under-Appliance Wand: Clean under and behind hard-to-move appliances and furniture with this adjustable 36” tool. Flip the extension piece over to clean the underside of appliances.
• Anti-Allergen Dust Brush: This brush features nylon fiber bristles specifically designed for removing fine dust and allergen particles from the most delicate surfaces.
• Home & Car Detail Kit: Deep-clean your car like a professional detailer, or clean hard-to-reach areas in your home. Micro-sized tools let you clean around delicate objects and access the tightest spaces like car vents and computer keyboards.
• Accessory Bag: This convenient accessory storage bag measures 32 cm x 70 cm and fits the Under-Appliance Wand. Smaller size available at sharkaccessories.com.

---

What are the benefits of registering the product?

• Get easier, faster product support and access to warranty information.
• Access troubleshooting and product care instructions.
• Be among the first to know about exclusive product promotions.

---

What does the five-year limited warranty cover?

The original unit and/or non-wearable components deemed defective, in SharkNinja’s sole discretion, will be repaired or replaced up to five (5) years from the original purchase date. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.

---

What does the warranty not cover?

• Normal wear and tear of wearable parts (such as foam filters, HEPA filters, pads, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.
• Any unit that has been tampered with or used for commercial purposes.
• Damage caused by misuse (e.g., vacuuming up water or other liquids), abuse, negligent handling, failure to perform required maintenance (e.g., not cleaning the filters), or damage due to mishandling in transit.
• Consequential and incidental damages.
• Defects caused by repair persons not authorized by SharkNinja. These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its parts) when the repair is performed by a repair person not authorized by SharkNinja.
• Products purchased, used, or operated outside North America.

---

How do I get service if the appliance fails to operate properly within the warranty period?

Visit sharkclean.com/support for product care and maintenance self-help. Customer Service Specialists are also available at 1-800-798-7398 to assist with product support and warranty service options, including the possibility of upgrading to VIP warranty service options for select product categories. SharkNinja will cover the cost for the customer to send in the unit for repair or replacement. A fee of $24.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

---

How do I initiate a warranty claim?

Call 1-800-798-7398 to initiate a warranty claim. You will need the receipt as proof of purchase. A Customer Service Specialist will provide you with return and packing instruction information.