SHARK FLEXBREEZE HYDROGO FA050EU (01) PDF DOCUMENT

According to Commission Regulation (EU) 206/2012 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to eco-design requirements for air conditioners and comfort fans, the specifications for the SHARK FLEXBREEZE HYDROGO FA050EU are as follows:

To use the car charger (sold separately) with your SHARK FLEXBREEZE HYDROGO FA050EU:

1. Firmly insert the car charger plug into a 12-volt outlet in your vehicle.

2. Insert the charger connector into the charging port on the back of the fan head.

The SHARK FLEXBREEZE HYDROGO FA050EU includes:

• Fan (Already assembled)

• Charger

The main features are:

CORDLESS: This is a 2-in-1 fan that can be used with or without the cord.

OUTDOORS: This fan can be enjoyed indoors or outdoors. DO NOT CHARGE OR USE IN THE RAIN.

VERTICAL TILT: Direct the airflow by manually adjusting the vertical tilt up to 45 degrees.

MISTING: Integrated misting suitable for both indoor and outdoor usage.

Power On/Off: Press the power button on the fan head to turn the fan on.

Fan Speed: Press the fan speed icon on the fan head to cycle between fan settings: Fan speeds 1-5 and NaturalBreeze modes. The LED lights will indicate the selected fan setting.

Misting Modes: Press the misting icon on the fan head to cycle between mist settings: consistent, interval, or OFF. The LED lights will indicate the selected mist setting. Tip: Try adjusting the fan speed while misting to customize your cooling experience.

The battery LED on the fan head indicates how much power your fan has:

• 70%-100%: green light

• 30%-69%: amber light

• 6%-29%: red light steady

• 5% and below: red light blinking

Charge Time: From 0% to fully charged battery takes approximately 3 hours.

Approximate Fan ONLY Runtime:

• MAXIMUM CORDLESS RUNTIME: 12 hours on fan speed 1.

• AVERAGE CORDLESS RUNTIME: 3.5 hours on fan speed 3.

• MAXIMUM CORDLESS PERFORMANCE: 1 hour on fan speed 5.

• PLUGGED IN: Indefinite runtime; the fan will charge while operating.

Mist Runtime:

• MAXIMUM MISTING RUNTIME: Up to 60 minutes of Interval misting per tank at any fan speed.

• MAXIMUM MISTING PERFORMANCE: Up to 30 minutes of Consistent misting per tank at any fan speed.

Note: The mister will automatically turn off after 1 hour in Consistent mode or 2 hours in Interval mode. This prevents dry running and system damage.

Detailed Battery Life Table:

To charge the fan, insert the charger into the charging port on the back of the fan head. DO NOT CHARGE OR USE IN THE RAIN.

Before every use, you should fully flush the system for at least one minute and rinse out the tank to prevent stagnant water from being misted.

1. First, empty all the water out of the tank: Hold the fan over a drain, open the water tank cap, then turn the fan upside down and allow all water to drain out.

2. Place the fan upright on a level, stable surface. Open the misting cap on the front grille of the fan, then turn on the misting function for 5 seconds to clear any remaining water from the system.

3. Place the fan in a well-ventilated space and allow it to air-dry completely.

NOTE: Leave the water tank cap open for 24 hours before closing and storing the unit.

The base is removable, so you can swap in different bases or add accessories that suit your needs.

1. To remove the base, gently press the release button and pull the base downward off the fan head post.

2. To reinstall the base, slide it onto the fan head post, over the button, until it clicks into place.

Changing the FAN SPEED will increase or decrease the airflow of the fan. There are 5 fan speed settings. To change the speed, press the fan icon on the fan speed head to cycle through the different speeds.

Turn on either of the NaturalBreeze modes to simulate natural wind conditions. To activate STRONG NaturalBreeze, press the fan speed icon until the corresponding LEDs are displayed. To transition to GENTLE NaturalBreeze, press the fan speed icon again. To deactivate, press the fan speed icon until you reach your desired fan speed setting.

NATURALBREEZE WIND PATTERNS

The misting feature is suitable for both indoor and outdoor use. Choose between 2 misting settings. To change the misting settings, press the Misting icon on the fan head. To turn off misting, press the Misting icon until no LEDs are illuminated.

To enable misting, OPEN the misting cap in the centre of the fan grill. When done misting, CLOSE the cap to prevent dripping.

Note: Misting will automatically shutoff after 1 hour in Consistent and 2 hours in Interval mode to prevent dry running and damaging the system. If you refill the water tank during use, the timer may turn off misting. To reactivate mist, press the Misting icon on top of the fan head. Repeat as needed. DO NOT attempt to mist with an empty water tank.

Make sure the fan has battery power by pressing the Power button. If the Battery LED indicator blinks red, then the fan needs to be charged. When the fan is charging, the battery LED will blink green.

If all the LEDs are flashing, the fan may be in Lock mode, which deactivates the fan to allow you to safely maintain or travel with it. To turn off Lock mode, press and hold the Power icon on the fan for 8 seconds. When Lock mode is successfully deactivated, the LEDs will display the Power On pattern.

If the battery level is low, the misting feature cannot be activated. Charge the fan battery to use misting.

Misting will automatically shutoff after 1 hour in Consistent and 2 hours in Interval mode to prevent dry running and damaging the system.

If you refill the water tank during use, misting may last longer than automatic shutoff timers. To reactivate mist, press the Misting icon on the top of the fan head. Repeat as needed. DO NOT attempt to mist with an empty water tank.

This fan is rain-resistant and will not be damaged by light rain. However, it is not suitable to withstand heavy rain or water submersion. Do not charge or use your fan in the rain.

This error state indicates an issue with the voltage of the charger. Please be sure to only use the provided Shark® charging cable and power supply intended for this product.

The fan must be in Lock mode when any maintenance is performed. Lock mode prevents the fan from accidentally powering on. It is also recommended to activate Lock mode when traveling with the fan.

We recommend using a damp cloth to wipe down the external surfaces of the fan every 6 months or as needed.

Clean the misting system every week or as needed. Using harder water will require more frequent cleaning.

Ensure the misting cap located in the centre of the fan grille is fully open. The misting system may clog if not maintained properly. See the Maintenance section for details on cleaning instructions.

It is recommended to perform a clean soak every week or as needed. Ensure you empty and dry the water tank completely after every use.

To perform a clean soak:

1. Activate LOCK MODE by holding down the power button for 8 seconds until the lights flash. This will temporarily disable all fan functions to prevent the fan from accidentally turning on during maintenance.

2. Fill the water tank with 150ml of undiluted distilled white vinegar (5% acetic acid by volume) and let sit for 5–7 minutes. DO NOT let the vinegar sit for more than 15 minutes.

3. Carefully dump the vinegar out of the tank.

4. Refill the tank with clean tap or filtered water.

5. Ensure the water tank and misting cap are fully sealed, then shake the unit for 10 seconds.

6. Carefully dump the water out of the tank.

7. Repeat steps 4, 5 and 6 once more to thoroughly rinse the water tank.

8. Deactivate LOCK MODE by holding down the power button for 8 seconds until the lights show the startup pattern. Please allow the water tank to dry completely before using the unit again.

LOCK MODE temporarily blocks all fan functions for 24 hours to prevent the fan from accidentally powering on during fan head maintenance or travel.

1. Activate Lock mode before traveling and performing maintenance to prevent the fan from accidentally powering on during transport. To activate, hold down the POWER icon on the fan head for 8 seconds until the LEDs begin to flash.

2. Lock Mode will automatically deactivate after 24 hours.

3. If you wish to deactivate Lock mode before 24 hours, hold down the POWER icon on the fan head for 8 seconds until the LEDs show the Power On pattern.