PYLE PDWM2958B (01) PDF DOCUMENT

To set up the PYLE PDWM2958B system and avoid interference, each unit may have many presented channels.

When using multiple receiver/transmitter sets together, each unit should be set to use a different channel.

1. The transmitter and antenna should be kept in a barrier-free, linear relative position.

2. Do not place the receiver close to metal surfaces or digital equipment.

3. Try to keep the receiver 1.5m above the floor and 1m away from the wall.

The parts of the receiver are as follows:

1. Power Switch

2. VOL. A (Volume for Channel A)

3. VOL. B (Volume for Channel B)

4. RF Signal Lamp

5. AF Signal Lamp

6. Power Signal Lamp

7. LCD Display

8. 1/4 Audio Output Socket

9. XLR Audio Output Socket

10. Power Input Socket

11. Charging Socket

12. ANT-A (Antenna)

Note: The images provided are indicative only; the actual product may differ.

The parts of the handheld transmitter are as follows:

1. Power signal lamp

2. LED display

3. Battery Cover

4. Frequency-change button

5. Power switch

Note: The images provided are indicative only; the actual product may differ.

The functions of the bodypack transmitter are as follows:

1. Clip microphone socket

2. LED light

3. Antenna

4. LED display

5. Frequency-change button

6. Power switch

Note: This only applies to some models.

Follow these steps to match the receiver and transmitter (this applies to some models):

1. Make sure the receiver is powered OFF.

2. On the transmitter, press and hold the frequency-change button, then press and hold the power button until the display starts flashing.

3. Turn ON the receiver. You will see the RF light on the receiver flashing.

4. Attention: For receivers that have an LED display, turn ON the receiver and wait for 3-5 seconds.

5. Go back to the transmitter and press the frequency-change button again.

6. Matching is successful if the RF light is solid ON or if the LED display shows the frequency. If not, repeat the process from step 1.

Connect the connector of the supplied lavalier microphone to the connecting jack of the transmitter. Set the transmitter to work in the wireless lavalier system mode.

Connect the connector of the supplied headset microphone to the connecting jack of the transmitter. Set the transmitter to work in the wireless headset system mode.

This procedure only applies to some models. To charge the microphone, connect the charging cable to the charging socket on the receiver.

CAUTION: For a charging microphone, you MUST NOT use an AA battery to power the microphone. You MUST use a 14500 lithium battery.

1. Transmitters must be matched to their corresponding receivers to prevent frequency interference. Refer to the “Matching receiver and transmitter” procedure.

2. Use different frequencies among the different transmitter units. The difference in frequency should be 3-4MHz for each transmitter.

Check the status of the system and follow the corresponding solution:

Status: Transmitter display or light is off.

Solution:

1. Turn on the transmitter.

2. Make sure the battery is installed correctly.

3. Replace the batteries.

Status: Receiver display or light is off.

Solution:

Make sure the adapter is plugged into the receiver DC socket, and the adapter has power.

Status: Receiver display or light indicates RF signal is present.

Solution:

1. Turn up the receiver volume.

2. Check the cable connection of the receiver.

Status: Receiver display or light indicates no RF signal; Transmitter and receiver power lights are on.

Solution:

1. Move the receiver away from metal objects.

2. Check if there is a barrier between the receiver and transmitter.

3. See the instructions for “Matching receiver and transmitter.”

If the receiver display or light indicates an RF signal is present, follow these steps:

1. Remove interference sources from nearby.

2. Change the working frequency of the receiver and transmitter.

3. Replace the transmitter batteries.

4. If using many sets together, increase the working frequency interval between the systems.

5. Maximize the volume button.

If you press the power button and the transmitter does not work or shuts down after a second, try the following:

1. Replace the batteries.

2. Re-press the power button after a few seconds.

Note: Some specifications may not apply to all models.

Channels: 16 Channels

SNR: 96db

Sensitivity: 96dbm

Frequency Response: 30~20kHz

Channel Interval: 500kHz

Output Impedance: 600 Ohm

Power Supply: 5V

Power Consumption: <85Ma

Display: LED Display

Note: Some specifications may not apply to all models.

Power Output: 10dbm

Frequency Response: 30kHz~20kHz

Power Supply (Normal battery): 3V

Power Supply (Lithium battery): 3.7V

Note: Some specifications may not apply to all models.

Power Output: 10dbm

Frequency Response: 30kHz~20kHz

Power Supply: 3V