Free English PYLE PDWM2880B (01) PDF Document. Free English PYLE PDWM2880B (01) PDF User Guide. Free English PYLE PDWM2880B (01) PDF User Manual. Free English PYLE PDWM2880B (01) PDF Owner Guide. Free English PYLE PDWM2880B (01) PDF Owner Manual. Free English PYLE PDWM2880B (01) PDF Reference Guide. Free English PYLE PDWM2880B (01) PDF Instruction Guide. Free English PYLE PDWM2880B (01) PDF Reference Manual. Free English PYLE PDWM2880B (01) PDF Instruction Manual. Free English PYLE PDWM2880B (01) PDF Operating Instructions.
CLICK HERE TO DOWNLOAD PYLE PDWM2880B (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are some setup tips for the PYLE PDWM2880B wireless microphone system?
To set up the system and to avoid interference, each unit may have many presented channels.
When using numbers of receivers/transmitters together, each unit should use different channels.
Tips
1. Transmitter and antenna should keep in a barrier-free linear relative position.
2. Do not place receiver close to metal surface object or digital equipment.
3. Try to keep receiver 1.5m above the floor and 1m away from the wall.
How do I match the receiver and transmitter for my PYLE PDWM2880B system?
1. Make sure the receiver is powered OFF.
2. On transmitter side, press and hold the frequency-change button, then press and hold the power button till the display is flashing.
3. Turn ON the receiver and then you will see the RF light is flashing.
4. Attention: For the receiver that has LED display, turn ON the receiver and wait for 3-5 seconds.
5. Get back to the transmitter side and re-press the frequency-change button.
6. Matching is successful if the RF light is ON or the LED display shows frequency, otherwise, re-do step 1 to step 5.
How do I connect the lavalier microphone to the bodypack transmitter on the PYLE PDWM2880B?
Connect the connector of the supplied lavalier microphone to the connecting jack of the transmitter. Set the transmitter work state in wireless lavalier system.
How do I connect the headset microphone to the bodypack transmitter on the PYLE PDWM2880B?
Connect the connector of the supplied headset microphone to the connecting jack of the transmitter. Set the transmitter work state in wireless headset system.
How do I charge the microphone for the PYLE PDWM2880B, and are there any precautions?
To charge the microphone, connect the charging cable to the charging socket on the receiver.
CAUTION: For charging microphone, MUST NOT use AA battery to power the microphone. MUST use 14500 lithium battery.
How do I configure multiple PYLE PDWM2880B systems to work together?
1. Transmitters match corresponding receivers to prevent frequency interference (See “Matching receiver and transmitter” for reference).
2. Using different frequencies among transmitters (The difference should be 3-4MHz for each transmitters).
How can I troubleshoot common issues with my PYLE PDWM2880B wireless microphone system?
| Problem | Status | Solution |
|---|---|---|
| No sound or sound is weak | Transmitter display or light is off | 1. Turn on transmitter 2. Make sure battery is installed right 3. Replace batteries |
| Receiver display or light is off | Make sure adapter is plugged into receiver DC socket, and the adapter is power supplied | |
| Receiver display or light indicate RF signal | 1. Turn up receiver volume 2. Check the cable connection of receiver |
|
| Receiver display or light indicate no RF signal; Transmitter and receiver power light is on | 1. Remove receiver away from metal objects 2. Check if barrier is between receiver and transmitter 3. See “Matching receiver and transmitter” |
|
| Distortion or unwanted noise bursts | Receiver display or light indicate RF signal | 1. Remove interference sources nearby 2. Change receiver and transmitter working frequency 3. Replace transmitter batteries 4. If using many sets together, increase working frequency interval of systems 5. Maximize the volume button |
| Failed to turn ON transmitter | Press power button, transmitter not working, or shut down after a second | 1. Replace batteries 2. Re-press power button after few seconds |
What are the specifications for the receiver of the PYLE PDWM2880B system?
Note: Some specifications may not apply to some models.
Channels: 16 Channels
SNR: 96db
Sensitivity: 96dbm
Frequency Response: 30~20kHz
Channel Interval: 500kHz
Output Impedance: 600 Ohm
Power Supply: 5V
Power Consumption: <85Ma
LED Display
What are the specifications for the handheld transmitter of the PYLE PDWM2880B system?
Note: Some specifications may not apply to some models.
Power Output: 10dbm
Frequency Response: 30kHz~20kHz
Power Supply: 3v (Normal battery)
Power Supply: 3.7V (Lithium battery)
What are the specifications for the bodypack transmitter of the PYLE PDWM2880B system?
Note: Some specifications may not apply to some models.
Power Output: 10dbm
Frequency Response: 30kHz~20kHz
Power Supply: 3v
CLICK HERE TO DOWNLOAD PYLE PDWM2880B (01) PDF DOCUMENT