Free English PYLE PDWM2950 (01) PDF Document. Free English PYLE PDWM2950 (01) PDF User Guide. Free English PYLE PDWM2950 (01) PDF User Manual. Free English PYLE PDWM2950 (01) PDF Owner Guide. Free English PYLE PDWM2950 (01) PDF Owner Manual. Free English PYLE PDWM2950 (01) PDF Reference Guide. Free English PYLE PDWM2950 (01) PDF Instruction Guide. Free English PYLE PDWM2950 (01) PDF Reference Manual. Free English PYLE PDWM2950 (01) PDF Instruction Manual. Free English PYLE PDWM2950 (01) PDF Operating Instructions.
CLICK HERE TO DOWNLOAD PYLE PDWM2950 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the setup tips to avoid interference with the PYLE PDWM2950?
To set up your PYLE PDWM2950 system and avoid interference, please follow these tips:
• To set up the system and to avoid interference, each unit may have many presented channels.
• When using multiple receiver/transmitter sets together, each unit should use different channels.
1. The transmitter and antenna should be kept in a barrier-free, linear relative position.
2. Do not place the receiver close to a metal surface or digital equipment.
3. Try to keep the receiver 1.5m above the floor and 1m away from the wall.
How do I match the receiver and transmitter for my PYLE PDWM2950?
To match the receiver and transmitter, please follow these steps:
1. Make sure the receiver is powered OFF.
2. On the transmitter, press and hold the frequency-change button, then press and hold the power button until the display is flashing.
3. Turn ON the receiver. You will see the RF light on the receiver start flashing.
4. Attention: For receivers that have an LED display, turn ON the receiver and wait for 3-5 seconds.
5. Return to the transmitter and press the frequency-change button again.
6. The matching process is successful if the RF light on the receiver is solid ON, or if the LED display shows the frequency. If not, please repeat steps 1 through 5.
How do I connect a lavalier microphone to the PYLE PDWM2950 bodypack transmitter?
Connect the connector of the supplied lavalier microphone to the connecting jack of the transmitter. Set the transmitter to the work state for a wireless lavalier system.
How do I connect a headset microphone to the PYLE PDWM2950 bodypack transmitter?
Connect the connector of the supplied headset microphone to the connecting jack of the transmitter. Set the transmitter to the work state for a wireless headset system.
How do I charge the microphone for my PYLE PDWM2950 system?
Some models support charging. Use the provided charging cable to connect the microphone’s charging socket to a power source.
CAUTION: For charging the microphone, you MUST NOT use AA batteries. You MUST use a 14500 lithium battery.
How should I configure multiple PYLE PDWM2950 systems to work together?
To prevent frequency interference when using multiple systems:
1. Ensure transmitters are matched to their corresponding receivers. (See “Matching receiver and transmitter” for reference).
2. Use different frequencies among the transmitters. The difference in frequency should be 3-4MHz for each transmitter.
How do I troubleshoot my PYLE PDWM2950?
| Problem | Status | Solution |
|---|---|---|
| No sound or sound is weak | Transmitter display or light is off |
1. Turn on transmitter 2. Make sure battery is installed right 3. Replace batteries |
| Receiver display or light is off | Make sure adapter is plugged into receiver DC socket, and the adapter is power supplied | |
| Receiver display or light indicate RF signal |
1. Turn up receiver volume 2. Check the cable connection of receiver |
|
| Receiver display or light indicate no RF signal; Transmitter and receiver power light is on |
1. Remove receiver away from metal objects 2. Check if barrier is between receiver and transmitter 3. See “Matching receiver and transmitter” |
|
| Distortion or unwanted noise bursts | Receiver display or light indicate RF signal |
1. Remove interference sources nearby 2. Change receiver and transmitter working frequency 3. Replace transmitter batteries 4. If using many sets together, increase working frequency interval of systems 5. Maximize the volume button |
| Failed to turn ON transmitter | Press power button, transmitter not working, or shut down after a second |
1. Replace batteries 2. Re-press power button after few seconds |
What are the specifications for the PYLE PDWM2950 system?
Some specifications may not apply to all models.
RECEIVER
Channels: 16 Channels
SNR: 96db
Sensitivity: 96dbm
Frequency Response: 30-20kHz
Channel Interval: 500kHz
Output Impedance: 600 Ohm
Power Supply: 5V
Power Consumption: <85Ma
LED Display
HANDHELD TRANSMITTER
Power Output: 10dbm
Frequency Response: 30kHz-20kHz
Power Supply: 3V (Normal battery)
Power Supply: 3.7V (Lithium battery)
BODYPACK TRANSMITTER
Power Output: 10dbm
Frequency Response: 30kHz-20kHz
Power Supply: 3V
CLICK HERE TO DOWNLOAD PYLE PDWM2950 (01) PDF DOCUMENT