Free English PYLE PDWM1988B (01) PDF Document. Free English PYLE PDWM1988B (01) PDF User Guide. Free English PYLE PDWM1988B (01) PDF User Manual. Free English PYLE PDWM1988B (01) PDF Owner Guide. Free English PYLE PDWM1988B (01) PDF Owner Manual. Free English PYLE PDWM1988B (01) PDF Reference Guide. Free English PYLE PDWM1988B (01) PDF Instruction Guide. Free English PYLE PDWM1988B (01) PDF Reference Manual. Free English PYLE PDWM1988B (01) PDF Instruction Manual. Free English PYLE PDWM1988B (01) PDF Operating Instructions.
CLICK HERE TO DOWNLOAD PYLE PDWM1988B (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the setup and usage tips for the PYLE PDWM1988B wireless microphone system?
To ensure proper setup and avoid interference with your PYLE PDWM1988B, please follow these guidelines:
Setup:
• To set up the system and to avoid interference, each unit may have many presented channels.
• When using numbers of receivers/transmitters together, each unit should use different channels.
Tips:
1. Transmitter and antenna should keep in a barrier-free linear relative position.
2. Do not place the receiver close to a metal surface object or digital equipment.
3. Try to keep the receiver 1.5m above the floor and 1m away from the wall.
What are the parts of the receiver for the PYLE PDWM1988B?
The receiver for the PYLE PDWM1988B has the following components:
1. Power Switch
2. VOL. A (Volume for Channel A)
3. VOL. B (Volume for Channel B)
4. RF Signal Lamp
5. AF Signal Lamp
6. Power Signal Lamp
7. LCD Display
8. 1/4 Audio Output Socket
9. XLR Audio Output Socket
10. Power Input Socket
11. Charging Socket
12. ANT-A / ANT-B (Antenna)
Note: The images provided are indicative only; the actual product may differ.
What are the parts of the handheld transmitter microphone for the PYLE PDWM1988B?
The handheld microphone for the PYLE PDWM1988B has the following components:
1. Power signal lamp
2. LED display
3. Battery Cover
4. Frequency-change button
5. Power switch
What are the functions of the Body Pack Transmitter for the PYLE PDWM1988B?
The functions of the body pack transmitter (only applies to some models) are:
1. Clip microphone socket
2. LED light
3. Antenna
4. LED display
5. Frequency-change button
6. Power switch
How do I match the receiver and transmitter for the PYLE PDWM1988B?
To match the receiver and transmitter for your PYLE PDWM1988B system, follow these steps:
1. Make sure the receiver is powered OFF.
2. On the transmitter side, press and hold the frequency-change button, then press and hold the power button until the display is flashing.
3. Turn ON the receiver and then you will see the RF light is flashing.
4. Attention: For the receiver that has an LED display, turn ON the receiver and wait for 3-5 seconds.
5. Get back to the transmitter side and re-press the frequency-change button.
6. Matching is successful if the RF light is ON or the LED display shows frequency; otherwise, re-do steps 1 to 5.
How do I connect a lavalier microphone to the bodypack transmitter of the PYLE PDWM1988B?
Connect the connector of the supplied lavalier microphone to the connecting jack of the transmitter. Set the transmitter work state in wireless lavalier system.
How do I connect a headset microphone to the bodypack transmitter of the PYLE PDWM1988B?
Connect the connector of the supplied headset microphone to the connecting jack of the transmitter. Set the transmitter work state in wireless headset system.
How do I charge the microphone for the PYLE PDWM1988B?
This only applies to some models. To charge the microphone, connect the charging cable to the charging socket on the receiver and the corresponding port on the microphone.
CAUTION: For charging the microphone, you MUST NOT use an AA battery to power the microphone. You MUST use a 14500 lithium battery.
How do I configure multiple PYLE PDWM1988B systems for simultaneous use?
To use multiple systems together, follow these steps:
1. Transmitters must match their corresponding receivers to prevent frequency interference. (See “Matching receiver and transmitter” for reference).
2. Use different frequencies among the transmitters. The difference should be 3-4MHz for each transmitter.
How can I troubleshoot issues with my PYLE PDWM1988B?
| Problem | Status | Solution |
|---|---|---|
| No sound or sound is weak | Transmitter display or light is off | 1. Turn on transmitter 2. Make sure battery is installed right 3. Replace batteries |
| Receiver display or light is off | Make sure adapter is plugged into receiver DC socket, and the adapter is power supplied | |
| Receiver display or light indicate RF signal | 1. Turn up receiver volume 2. Check the cable connection of receiver |
|
| Receiver display or light indicate no RF signal; Transmitter and receiver power light is on | 1. Remove receiver away from metal objects 2. Check if barrier is between receiver and transmitter 3. See “Matching receiver and transmitter” |
|
| Distortion or unwanted noise bursts | Receiver display or light indicate RF signal | 1. Remove interference sources nearby 2. Change receiver and transmitter working frequency 3. Replace transmitter batteries 4. If using many sets together, increase working frequency interval of systems 5. Maximize the volume button |
| Failed to turn ON transmitter | Press power button, transmitter not working, or shut down after a second | 1. Replace batteries 2. Re-press power button after few seconds |
What are the specifications for the receiver of the PYLE PDWM1988B?
The specifications for the receiver are as follows. Note that some specifications may not apply to all models.
Channels: 16 Channels
SNR: 96db
Sensitivity: 96dbm
Frequency Response: 30~20kHz
Channel Interval: 500kHz
Output Impedance: 600 Ohm
Power Supply: 5V
Power Consumption: <85Ma
LED Display
What are the specifications for the handheld transmitter of the PYLE PDWM1988B?
The specifications for the handheld transmitter are as follows. Note that some specifications may not apply to all models.
Power Output: 10dbm
Frequency Response: 30kHz~20kHz
Power Supply (Normal battery): 3V
Power Supply (Lithium battery): 3.7V
What are the specifications for the bodypack transmitter of the PYLE PDWM1988B?
The specifications for the bodypack transmitter are as follows. Note that some specifications may not apply to all models.
Power Output: 10dbm
Frequency Response: 30kHz~20kHz
Power Supply: 3V
CLICK HERE TO DOWNLOAD PYLE PDWM1988B (01) PDF DOCUMENT