PIZZELLO CALDO (01) PDF Document

1. If there are parts missing, please send a message with the name of the missing part regarding the first page of instructions for a replacement.

2. If there is any damage, please send clear photos of the damaged part as an attachment to receive the best solution.

3. Please do not dispose of the original product box until you confirm you have received the complete and correct item.

If you smell gas, follow these steps immediately:

• Shut off gas to the appliance.

• Extinguish any open flame.

• If the odor continues, leave the area immediately.

• After leaving the area, call your gas supplier or fire department.

Failure to follow these instructions could result in a fire or explosion, which could cause property damage, personal injury, or death.

LP Safety:

a. Do not store a spare LP-gas cylinder under or near this appliance.

b. Never fill the cylinder beyond 80 percent full.

c. If the information in “(a)” and “(b)” is not followed exactly, a fire causing death or serious injury may occur.

Do not use this appliance under overhead combustible surfaces.

Minimum Clearances:

• Bottom: Non-Combustible Surface

• Top: 60 inches

• Sides: 36 inches

• For Installation on (or over) non-combustible floors only

Gas Supply Specifications:

• Max. Input: 50,000 BTU/h

• Max. Gas Supply Pressure: 250 PSI

• Min. Gas Supply Pressure: 25 PSI

All LP cylinders to be used with this appliance must be:

a. Constructed and marked in accordance with the specifications for LP-gas cylinders Standard, CAN/CSA B339, Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods.

b. Provided with a listed overfilling prevention device.

c. Provided with a cylinder connection device compatible with the connection for outdoor cooking appliances.

d. Only a 20 lb (9 kg) LP gas cylinder is to be used for this appliance, approximately 18″ (46 cm) high & 12″ (30 cm) diameter.

1. Be sure the cylinder valve and appliance valves are “off”.

2. Place the full LP gas cylinder on the tank stabilizer ring. Secure the base of the LP gas cylinder by hand tightening the wing-nut collar.

3. Center the nipple in the cylinder valve and hold in place.

4. Using the other hand, turn the hand wheel clockwise until there is a positive stop. Do not use tools.

5. Hand tighten only. When making the connection, hold the regulator in a straight line with the cylinder valve, so as not to cross thread the connection.

6. Leak test the connection.

1. Be sure the cylinder valve and appliance valves are “off” before disconnection.

2. Using one hand, turn the hand wheel anticlockwise.

1. DO NOT USE OR PERMIT SOURCES OF IGNITION IN THE AREA WHILE DOING THE LEAK TEST. THIS INCLUDES SMOKING.

2. Leak testing should be done once per year or whenever the LP gas cylinder or any other gas system part is taken apart, serviced or replaced, whichever is more frequent.

3. Ensure all gas system coupling joints are tight and properly attached.

4. Prepare a leak testing solution of half liquid detergent and half water.

5. Apply the solution to the LP gas delivery system at points: Fire Table valve coupling, gas hose regulator, and cylinder coupling.

6. The leak(s) must be stopped by tightening the loose joints, if possible, or by replacing the faulty part(s) with the part(s) recommended by the appliance manufacturer.

THE APPLIANCE IS NOT TO BE USED UNTIL ANY LEAK IS CORRECTED. If attempts to stop the leak(s) are unsuccessful, the LP gas supply must be shut off at the cylinder valve or the cylinder must be removed.

Hose Inspection: Inspect the hose prior to each use of the unit. The hose assembly must be replaced prior to operation if there is evidence of excessive abrasion or wear, or if the hose is damaged. The replacement hose assembly shall be the one that is specified by the manufacturer.

Burner Inspection: Inspect the burner prior to each use. The burner must be replaced prior to the appliance being put into operation if there is evidence of damage.

General Inspection: The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners, and circulating air passageways of the appliance be kept clean.

NOTE: Please do not tighten all the screws until step 5.

Step 1: Connect the Left Legs (14) and Right Legs (15) to the Front Panel (1) using 4 PCS of screw C. Then, connect the Left Legs (14) and Right Legs (15) to the Back Panel (2) with another 4 PCS of screw C. Note: Part 14 (Left Leg) has two mounting holes and should be installed on the side farther away from the middle frame bar. Part 15 (Right Leg) has four mounting holes and should be installed on the side closer to the middle frame bar.

Step 2: Connect the Front Panel (1) assembly to the Table Top (6) with 2 PCS of screw B and 2 PCS of washer D.

Step 3: Connect the Back Panel (2) assembly to the Table Top (6) with 2 PCS of screw B and 2 PCS of washer D.

Step 4: Connect the Right Side Panel (5) to the Front Panel (1) and Back Panel (2) with 8 PCS of screw B.

Step 5: Connect the Support Rod (8) to the Front Panel (1) and Back Panel (2) with 4 PCS of screw B. You may now tighten all screws from the previous steps.

Step 6: Connect the Left Side Panel (3) to the Tank Base (4) with 2 PCS of screw C.

Step 7: Stretch the glide track. Assemble the part 9L (LEFT track) to the Back Panel (2) with 2 PCS of screw A. Assemble the part 9R (RIGHT track) to the Front Panel (1) with 2 PCS of screw A.

Step 8: Connect the glide track to the Tank Base (4) with 4 PCS of screw C.

Step 9: Connect the Fixed Links (10) to the Left Side Panel (3) and the glide track (9) with 4 PCS of screw B.

Step 10: Put the Glass Fire Stone (12) into the burner tray, and close the Lid (7).

Glass Rocks shall be arranged neatly and evenly in the burner tray. Ensure the igniter cover is not covered by glass rocks. This helps air circulate. Take care to keep rocks out of the igniter cover and keep the igniter clean of dust. For best flame results, adjust the rocks to expose the burner tube holes.

WARNINGS:

• Never handle glass rocks which have not been allowed to cool from exposure to flame. Never attempt to rearrange rocks while the unit is ignited.

• Rocks are not to exceed 5 kg or 15.5 lb.

• Never use a lid or cover to extinguish the flame on your Fire Table.

• Avoid glass dust. Always wear gloves to handle rocks; use caution for glass dust when handling and use a rag to wipe it away. Glass dust may result during shipping.

Before igniting for the first time, follow steps 1 through 5. A 1 AAA 1.5V battery is needed and is not included.

Step 1: Ensure the unit valve dial is in the “OFF” position by pushing and turning it clockwise until the dial stops.

Step 2: Connect the LP gas cylinder.

Step 3: Ensure the gas hose is not contacting the top of the Fire Table enclosure and the tank is stabilized in the collar with the wing nut. Caution: Always ensure the gas valve orifice and burner tube venturi are clear of all debris including spider webs.

Step 4: ***SLOWLY*** turn the cylinder valve to the open position to avoid tripping the excess flow safety device in the gas regulator.

Step 5: Leak Test all connections.

Step 6: Your Fire Table is equipped with an auto spark ignition. Push the knob in and slowly turn counter-clockwise to the high position. The ignitor will spark and ignite the gas. Should the appliance fail to ignite on the first try, promptly repeat the ignition attempt within 5 seconds. If a third attempt fails to ignite, rotate the knob to the “off” position and wait 5 minutes before attempting to ignite again.

Step 7: Once the unit is burning normally, set the dial to the desired flame height.

Upon igniting the appliance, visually verify that the burner is burning. The presence of flames will confirm the burner is burning. Periodically check that the burner flame is present during operation.

If there are no flames present, the appliance is likely not burning. IMMEDIATELY turn the valve to the “off” position if it is not already and repeat the ignition procedure.

• Normal Flame: The burner flame is normally yellow.

• Blue/Small Flame: If the burner flame is blue and very small, check the gas cylinder, as it may be low on gas pressure or empty.

• Lifting Flames/Black Smoke: If flames lift away from the burner, backfire happens, or produce thick black smoke, the fire pit should be turned off immediately. Do not operate it again until the unit is serviced and/or repaired by a qualified service technician.

Step 1: Wait 5 minutes for any gas to dissipate. Locate the igniter cable under the table. Ensure the igniter cable is firmly attached to the gas valve. Follow the ignition sequence again. If still no results after three tries, move to step 2.

Step 2: Turn the gas cylinder valve to the Closed position. Wait 5 minutes for any gas to dissipate. Ensure the igniter cover is not covered by glass rocks. This helps air circulate. Inspect the ignition electrode (under the igniter cover) to ensure it is free from dust and not blocked by glass rocks or other debris. Use a dry clean cloth or tissue to very lightly wipe the igniter tip clean.

After waiting for 5 minutes, visually inspect the spark by rotating the knob to high without turning the gas back on at the cylinder. Ensure the spark gap is 3 – 5mm (1/8″ – 3/16″) from the burner port and has a clear path. Once you ensure the igniter is operating properly, repeat the ignition sequence.

Step 1: Check the thermocouple condition. If it’s defective, you may need a replacement.

Step 2: Check the thermocouple end nut condition. Tighten the nut if it’s loose.

Step 3: If both parts are in good condition, further checking may be required.

Step 1: Check the propane level. If less than half full, replace the cylinder. Repeat the ignition sequence.

Step 2: If the propane cylinder is full and you still experience low flame, or the flame height does not appear to be normally adjusted by the gas knob, it is likely that the excess flow safety device has been tripped in the hose regulator. Follow the corrective action steps below.

Corrective Action:

a. Close the propane cylinder valve.

b. Open and then close the Fire Table gas knob valve to release pressure.

c. Disconnect and reconnect the propane cylinder valve connection.

d. Slowly open the propane cylinder valve.

e. Perform a Leak Test and follow the Ignition sequence.

Step 1: Access the Fire Table interior. Turn the gas cylinder valve to the “Closed” position.

Step 2: Turn the gas knob on the Fire Table to the “OFF” position by pushing and turning the knob clockwise.

Step 3: Allow the unit to cool for at least five (5) minutes before relighting.

1. Keep your Fire Table out of the rain and store it in a dry place.

2. If you experience signs of your propane cylinder “freezing off” or lower flames than usual, turn the burner control setting to low for 5-10 minutes, or replace the cylinder with a full one.

3. Ensure that you clean the top of your Fire Table after every use. Simply use warm soapy water to wipe it down. Do not use abrasive cleaners. Especially, DO NOT USE PETROLEUM BASED SOLVENTS TO CLEAN YOUR FIRE TABLE AS THIS WILL DESTROY YOUR WICKER RESIN TABLE MATERIAL.

4. Remove any debris and leaves which may have accumulated in your Fire Table burner tray before igniting.

• Expected burn time for a full 20 lb (9kg) propane cylinder is between 12 and 18 hours depending on the flame height.

• This is NOT a toy.

• The fire table will become extremely hot during operation! – DO NOT TOUCH THE BURNER TRAY OR GLASS ROCKS while the fire table is in operation!

• Do not place ANY cover on the fire table while it is in operation.

• Do not rest anything on or over the burner tray while the fire table is in operation.

• The fire table is a decorative gas appliance only. NEVER cook food on the fire table.

• Wait at least 30 minutes after turning off the fire table to allow it to cool down before touching the burner tray, glass rocks, or putting ANY cover over the fire table.

• Ensure that all adults and children are aware of the hazard of high-surface temperatures and stay away to avoid burns or clothing ignition.

• Children should be supervised at all times when using this unit without exception.

• Do not place any objects other than supplied rocks inside the burner component of the Fire Table.

• Do not add wood or any other materials to the fire.

• Your Fire Table is designed to safely combust propane only.

• Do not connect to a remote gas supply. Consult a certified gas technician.

• Do not use this appliance if any part has been under water. Immediately call a qualified service technician.

• Do not leave this appliance uncovered in the rain.

• Always inspect and clear all valve and gas orifices of any foreign debris including spider webs prior to lighting.

• Never store a spare LP cylinder inside the LP cylinder compartment.