BASEUS BLADE2 PPBLD2-65 (01) PDF Document

To avoid damage to yourself and your property, please follow these instructions when using and storing the BASEUS BLADE2 PPBLD2-65:

1. This is NOT a toy. Place this product in areas that are not easily accessible by children and do not allow them to operate it.

2. Charge this product with a charger approved by local safety standards to prevent danger or damage.

3. DO NOT apply pressure and avoid collisions. The battery and circuit may be damaged if the product falls from a great height, experiences intense shocks, or is immersed in liquid. If this occurs, please avoid using the product.

4. If the product shows deformation, leakage, or a radical decline in performance, stop using it.

5. DO NOT charge any device or recharge this product in places that may affect its heat dissipation, such as pants pockets, enclosed bags, beds, or couches. Ensure the product is not under any cover when operating. When charging other devices for prolonged periods, DO NOT stack any device on top of this product, as it might affect its heat dissipation.

6. This product CAN NOT be disassembled, subjected to pressure, pierced, short-circuited, immersed in liquid, disposed of in a fire, or exposed to high temperatures or heat sources greater than 140°F (60°C).

7. DO NOT place this product in areas with extremely high temperatures, such as under direct sunlight or in a vehicle with a very high interior temperature.

8. This product contains lithium batteries; DO NOT disassemble it to avoid danger or battery damage.

9. This is not domestic waste. It should be handed over to a designated facility for electronic device recycling.

1. Please fully charge the BASEUS BLADE2 PPBLD2-65 before using it for the first time.

2. Power banks have conversion efficiency, so the battery capacity of the power bank is not equal to the rechargeable capacity.

3. Please choose an appropriate charger for recharging this product and suitable cables when charging other devices.

4. Please ensure some supervision is in progress when recharging this product; DO NOT charge this product without any care.

5. Please remove the cable when done recharging this product or finished charging any other device to preserve the product’s integrity.

6. If the indication does not light up after pressing the power button, please recharge the product.

7. For long-term storage, preserve this product with a battery percentage between 25%-50%. Place it in a cool and dry environment. To slow down battery aging, avoid storing this product in an empty or fully charged state for long periods.

8. Please do not dismantle the product by yourself. Improper use or placement may compromise the service life or damage the product.

1. This product does not contain any user-serviceable parts, and the rechargeable battery is not replaceable.

2. Putting the battery pack into fire or heating it in an oven, as well as subjecting the battery pack to mechanical squeezing or cutting, may result in an explosion.

3. Placing the battery pack in an extremely high-temperature environment may cause an explosion or leakage of flammable liquids or gases.

4. Subjecting the battery pack to extremely low air pressure may cause an explosion or leakage of flammable liquids or gases.

Name: Power Bank

Model No.: PPBLD2-65

Battery: Polymer Lithium Battery

Capacity: 12000mAh/46.44Wh

Energy conversion rate: ≥75%

Type-C1 input: 5V=3A; 9V=3A; 12V=3A; 15V=3A; 20V=3A

Type-C2 input: 5V=3A; 9V-3A; 12V=3A; 15V=3A; 20V-3A

Type-C1 output: 5V-3A; 9V-3A; 12V=3A; 15V=3A; 20V-3.25A

Type-C2 output: 5V=3A; 9V=3A; 12V-3A; 15V-3A; 20V-3.25A

Type-C1+Type-C2 output: 45W+20W

5V Total output: 5V-6A

Size: 161.6×132×10.2mm

Net weight: ≈328g

Power bank × 1

Charging cable × 1

User manual × 1

Warranty card × 1

Storage bag × 1

In idle mode, press the power button once to display the remaining battery power. After approximately 30 seconds, the screen will go into screensaver mode. If there is no operation after approximately 30 seconds, the product will automatically turn off the output.

When a device is connected for charging or discharging, the working status and voltage/current values of each port will be displayed individually.

1. Press the power button to turn on the power bank. The Bluetooth is in broadcasting mode. Click on the “+” button in the Baseus app at the top right corner to add a product.

2. Select the “Blade 2” product, click on “add device”, and complete the addition.

Note: The product uses Bluetooth to connect with the phone. When the distance is far (greater than 10 meters), the app may not respond immediately. It is recommended to stay close to the product for a better user experience.

Once connected to the app, you can access several features:

• Theme and Mood Text: Click on the theme to set the screen display background color and customize mood text, with a limit of 20 characters.

• Timer Function: Click on the timer function to access quick settings or customize reminders within 24 hours.

• Countdown Shutdown: Click on the countdown shutdown to perform quick or customized shutdown tasks within 24 hours, automatically turning off the power bank output.

• Low Current Mode: After activating the low current mode, the device will remain powered on for up to 4 hours.

Note: All of the above tasks need to be performed while the power bank is turned on. When the low current mode, timer mode, and countdown shutdown task are active simultaneously, the countdown shutdown task will take priority.

Operating temperature: non-tropical area, 0°C to 25 °C

Storage temperatures: 0 °C to 40 °C

The 5-year icon refers to the “valid period for environment-friendly use,” not the product quality assurance period. All electronic products contain toxic and harmful substances such as lead, mercury, and cadmium. The overdue use of these products may lead to leakage or mutation of these substances, causing environment pollution or serious damage. The term “environment-friendly use period” means that all electronic products shall be used within this validity period. The manufacturer will not be held liable for safety issues caused by using the product beyond its safe service life.

This form is compiled in accordance with SJ/T 11364.

O: Indicates that contents of the toxic and hazardous substances in all homogeneous materials are below the limit requirements specified by GB/T 26572 standard.

X: Indicates that contents of the toxic and hazardous substances exceed the limit requirements specified by GB/T 26572 standard in at least one homogeneous material of the component.