PIZZELLO PASSIONE (01) PDF Document

If there are any missing parts for your PIZZELLO PASSIONE, please send a message with the name of the missing part regarding the 6th page of the instructions to receive a replacement.

If there is any damage, please send clear photos of the damaged part. A solution will be offered soon after checking the photos.

Please do not dispose of the original product box for your PIZZELLO PASSIONE until you confirm you have received the complete and correct item.

The PIZZELLO PASSIONE fire pit table requires one 1 AAA 1.5V battery to ignite. Please note that the battery is not included.

If you smell gas, follow these steps immediately:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. If the odor continues, leave the area immediately.

4. After leaving the area, call your gas supplier or fire department.

Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

DANGER: FIRE OR EXPLOSION HAZARD

If you smell gas: Shut off gas to the appliance, extinguish any open flame, leave the area immediately if odor continues, and call your gas supplier or fire department after leaving.

WARNING: FLAMMABLE MATERIALS

Do not store or use gasoline, or other flammable vapors and liquids, in the vicinity of this or any other appliance. An LP-cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

WARNING: OUTDOOR USE ONLY

Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

DANGER: CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent, car, or home.

WARNING: IMPROPER INSTALLATION

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

a. Do not store a spare LP-gas cylinder under or near this appliance.

b. Never fill the cylinder beyond 80 percent full.

c. If the information in “(a)” and “(b)” is not followed exactly, a fire causing death or serious injury may occur.

Do not use this appliance under overhead combustible surfaces.

MINIMUM CLEARANCES:

• Bottom: Non-Combustible Surface

• Top: 60 inches

• Sides: 36 inches

• For installation on (or over) non-combustible floors only

SPECIFICATIONS:

• Max. Input: 50,000 BTU/h

• Max. Gas Supply Pressure: 250 PSI

• Min. Gas Supply Pressure: 25 PSI

All LP cylinders to be used with the PIZZELLO PASSIONE must be:

a. Constructed and marked in accordance with the specifications for LP-gas cylinders Standard, CAN/CSA B339, Cylinders, Spheres and Tubes for the Transportation of Dangerous Goods.

b. Provided with a listed overfilling prevention device.

c. Provided with a cylinder connection device compatible with the connection for outdoor cooking appliances.

d. Only a 20 lb (9 kg) LP gas cylinder is to be used for this appliance, approximately 18″ (46 cm) high & 12″ (30 cm) diameter.

Cylinders used with this unit must have a collar to protect the cylinder valve.

Please ensure that all adults and children who use or are near the PIZZELLO PASSIONE are aware of the hazard of high surface temperatures and should use caution and stay away to avoid burns or clothing ignition. Carefully supervise young children in the area of this appliance. Clothing or other flammable materials should not be hung from the appliance or placed on or near it. Any guard or other protective device removed for servicing must be replaced prior to operating the appliance.

1. Be sure the cylinder valve and appliance valves are “off”.

2. Place a full LP gas cylinder on the tank stabilizer ring. Secure the base of the LP gas cylinder by hand tightening the wing-nut collar.

3. Center the nipple in the cylinder valve and hold in place.

4. Using the other hand, turn the hand wheel clockwise until there is a positive stop. Do not use tools.

5. Hand tighten only. When making the connection, hold the regulator in a straight line with the cylinder valve, so as not to cross thread the connection.

6. Leak test the connection.

1. Be sure the cylinder valve and appliance valves are “off” before disconnection.

2. Using one hand, turn the hand wheel anticlockwise.

1. Do not use or permit sources of ignition in the area while doing the leak test. This includes smoking.

2. Leak testing should be done once per year or whenever the LP gas cylinder or any other gas system part is taken apart, serviced or replaced, whichever is more frequent.

3. Ensure all gas system coupling joints are tight and properly attached.

4. Prepare a leak testing solution of half liquid detergent and half water.

5. Apply the solution to the LP gas delivery system at these points: Fire Table valve coupling, gas hose regulator, and cylinder coupling.

6. The leak(s) must be stopped by tightening the loose joints, if possible, or by replacing the faulty part(s) with the part(s) recommended by the appliance manufacturer. The appliance is not to be used until any leak is corrected.

Inspect the hose prior to each use of the unit. The hose assembly must be replaced prior to operation if there is evidence of excessive abrasion or wear, or if the hose is damaged. A replacement hose assembly shall be the one that is specified by the manufacturer.

Inspect the burner prior to each use. The burner must be replaced prior to operation if there is evidence of damage.

Should any part of the appliance (including the burner) become soiled or dirty, wipe lightly with a damp cloth. Do not use flammable or corrosive cleaning products on or near this unit.

Ensure the gas hose is placed in an area where it is unlikely to be tripped over or subject to other accidental damage.

Keep the appliance area clear and free from combustible materials, gasoline and other flammable vapors and liquids.

NOTE: Please do not tighten all the screws until step 8.

ATTENTION: When installing, it is suggested you assemble it on the carton which came with the product, or any other clean floor to avoid the desktop being scratched.

Step 1: Connect the 2 tabletops (A) with 4 PCS screws (P), 8 PCS washers (R) and 4 PCS nuts (Q).

Step 2: Connect the front panel (B) to the tabletops (A) with 2 PCS screws (T).

Step 3: Connect the back panel (C) to the tabletops (A) with 2 PCS screws (T).

Step 4: Connect one side panel (D) to the front panel (B) and back panel (C) with 4 PCS screws (K). For easy assembly, assemble the holes below first, then flip the side panel up to assemble the holes above.

Step 5: Connect another side panel (D) to the front panel (B) and back panel (C) with 4 PCS screws (K). Assemble the holes below first, then flip the side panel up to assemble the holes above.

Step 6: Connect the tank base (F) to the front panel (B) and back panel (C) with 4 PCS screws (K).

Step 7: Connect 2 connectors (G) to the front panel (B) and back panel (C) with 4 PCS screws (T).

Step 8: Connect 2 connectors (G) to the tabletops (A) with 4 PCS screws (T). You may now tighten all the screws from the previous steps.

Step 9: Place the burner (X) into the tabletops (A), then fix the burner to the tabletops with 4 PCS screws (S). NOTE: Tilt the burner to insert the switch box, then flatten and screw it in.

Step 10: Assemble the doorknob (J) with 1 PC screw (U).

Step 11: Put the fire glass stone (Y) into the burner (X), and close the lid (E).

Glass Rocks shall be arranged neatly and evenly in the burner tray. Ensure the igniter cover is not covered by glass rocks as this helps air circulate. Take care to keep rocks out of the igniter cover and keep the igniter clean of dust. For best flame results, adjust the rocks to expose the burner tube holes. The rocks are not to exceed 7 kg or 15.5 lb.

WARNING: Avoid glass dust. Always wear gloves to handle rocks. Use a rag to wipe glass dust, which may result during shipping. Never handle glass rocks which have not been allowed to cool from exposure to flame. Never attempt to rearrange rocks while the unit is ignited. Never use a lid or cover to extinguish the flame on your Fire Table.

Before igniting the unit for the first time, follow steps one through 5. A 1AAA 1.5V battery is needed (NOT included).

STEP 1: Ensure that unit valve dial is in the “OFF” position by pushing and turning clockwise until the dial stops.

STEP 2: Connect the LP gas cylinder as per the “Connection” section.

STEP 3: Ensure the gas hose is not contacting the top of the Fire Table enclosure and the tank is stabilized in the collar with the wing nut. Caution: Always ensure the gas valve orifice and burner tube venturi is clear of all debris including spider webs.

STEP 4: ***SLOWLY*** turn the cylinder valve to the open position to avoid tripping the excess flow safety device in the gas regulator.

STEP 5: Leak Test all connections.

STEP 6: Your PIZZELLO PASSIONE is equipped with an auto spark ignition. Push the knob in and slowly turn counter-clockwise to the high position. The ignitor will spark and ignite the gas. Should the appliance fail to ignite on the first try, promptly repeat the ignition attempt within 5 seconds. If a third attempt fails to ignite the Fire Table, then rotate the knob to the “off” position and wait 5 minutes before attempting to ignite again.

STEP 7: Once the unit is burning normally, set the dial to the desired flame height.

Upon igniting the appliance, visually verify that the burner is indeed burning. The presence of flames will confirm that the burner is burning. Periodically check that the burner flame is present during operation.

If there are no flames present, the appliance is likely not burning. In this case, IMMEDIATELY turn the valve to the “off” position if it is not already, and repeat the ignition procedure.

Normally the burner flame is yellow. A normal flame has a yellow tip and a primarily blue flame.

If the burner flame is blue and very small, please check the gas cylinder, as it may have low gas pressure or be empty. If there is enough gas in the cylinder, contact customer service.

If flames lift away from the burner, backfire happens, or thick black smoke is produced, the fire pit should be turned off immediately. Do not operate it again until the unit is serviced and/or repaired by a qualified service technician.

STEP 1: Wait 5 minutes for any gas to dissipate. Locate the igniter cable under the table. Ensure the igniter cable is firmly attached to the gas valve. Follow the ignition sequence again. If still no results after three tries, move to step 2.

STEP 2: Turn the gas cylinder valve to the Closed position. Wait 5 minutes for any gas to dissipate. Ensure the igniter cover is not covered by glass rocks. This helps air circulate. Inspect the ignition electrode (under the igniter cover) to ensure it is free from dust and not blocked by glass rocks or other debris. Use a dry clean cloth or tissue to very lightly wipe the igniter tip clean.

After waiting for 5 minutes, visually inspect the spark by rotating the knob to high without turning the gas back on at the cylinder. Ensure the spark gap is 3 – 5mm (1/8″ – 3/16″) from the burner port and has a clear path. Once you ensure the igniter is operating properly, repeat the ignition sequence.

If the fire is on when you push in the dial knob, but goes off when you release it, follow these steps:

STEP 1: Check the thermocouple condition. If it’s defective, contact customer service for a thermocouple replacement.

STEP 2: Check the thermocouple end nut condition. Tighten the nut if it’s loose.

STEP 3: If both parts are in good condition, contact customer service for details checking.

STEP 1: Check the propane level. If less than half full, replace the cylinder. Repeat the ignition sequence.

STEP 2: If the propane cylinder is full and your PIZZELLO PASSIONE experiences a low flame, or flame height does not appear to be normally adjusted by the gas knob, it is likely that the excess flow safety device has been tripped in the hose regulator. To correct this, perform the following actions:

a. Close the propane cylinder valve.

b. Open and then close the Fire Table gas knob valve to release pressure.

c. Disconnect and reconnect the propane cylinder valve connection.

d. Slowly open the propane cylinder valve.

e. Perform a Leak Test and follow the Ignition sequence.

STEP 1: Access the Fire Table interior. Turn the gas cylinder valve to the “Closed” position.

STEP 2: Turn the gas knob on the Fire Table to the “OFF” position by pushing and turning the knob clockwise.

STEP 3: Allow the unit to cool for at least five (5) minutes before relighting.

Your PIZZELLO PASSIONE requires periodic maintenance to keep it in good running order.

1. Keep your Fire Table out of the rain and store it in a dry place. Covers are available for purchase.

2. If you experience signs of your propane cylinder “freezing off” or start to experience lower flames than usual, turn the burner control setting to low for 5-10 minutes, or replace the cylinder with a full one.

3. Ensure that you clean the top of your Fire Table after every use to keep it looking great. Simply use warm soapy water to wipe down your Fire Table. Do not use abrasive cleaners. Especially, DO NOT USE PETROLEUM BASED SOLVENTS TO CLEAN YOUR FIRE TABLE AS THIS WILL DESTROY YOUR WICKER RESIN TABLE MATERIAL.

4. Remove any debris and leaves which may have accumulated in your Fire Table burner tray before igniting.

• The anticipated burn time for your PIZZELLO PASSIONE using a full 20 lb (9kg) propane cylinder is between 12 and 18 hours depending on the flame height.

• This is NOT a toy.

• The fire table will become extremely hot during operation! DO NOT TOUCH THE BURNER TRAY OR GLASS ROCKS while the fire table is in operation!

• Do not place ANY cover on the fire table while it is in operation.

• Do not rest anything on or over the burner tray while the fire table is in operation.

• The fire table is a decorative gas appliance only. NEVER cook food on the fire table.

• Wait at least 30 minutes after turning off the fire table to allow it to cool down before touching the burner tray, glass rocks, or putting ANY cover over it.

• Children should be supervised at all times when using this unit without exception.

• Do not place any objects other than supplied rocks inside the burner component.

• Do not add wood or any other materials to the fire.

• Your Fire Table is designed to safely combust propane only. Do not connect to a remote gas supply.

• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect and replace any part of the control system and gas control.

• Do not leave this appliance uncovered in the rain.

• Always inspect and clear all valve and gas orifices of any foreign debris including spider webs prior to lighting.

• Never store a spare LP cylinder inside the LP cylinder compartment.