PETLIBRO POLAR PLAF109 (01) PDF Document

The PETLIBRO POLAR PLAF109 Wet Food Feeder comes with the following items:

• 1 × Automatic Pet Feeder

• 1 x Power Adapter

• 1 x Quick Start Guide

• 1 x User Manual

The main components of the PETLIBRO POLAR PLAF109 are:

1. Body

2. Top Lid

3. Rotating Food Section Lid

4. Temperature Sensor

5. Food Bowl

6. Top Lid Release Button

7. Status Indicator

8. Cooling Vent

9. Power Port

10. Reset Button

11. Battery Compartment (Batteries not included)

The PETLIBRO POLAR PLAF109 has two main buttons with the following operations:

Top Lid Release Button: Press to open the top lid.

Reset Button: Press and hold for three seconds to reset the feeder.

Power on:

1. Place the feeder on a level surface, and ensure that neither the left nor right cooling vents are obstructed by foreign objects.

2. Plug in the power cable, and the status indicator will flash white.

App Control:

1. Download and install the PETLIBRO app from your device’s app store.

2. Follow the in-app instructions to configure the network. Note: This feeder only supports 2.4GHz networks.

1. Press the top lid release button to open the top lid of the feeder.

2. Take out the food bowl and add an appropriate amount of wet food to it. Do not exceed the maximum food level line. For hot food, allow it to cool to room temperature before adding it to the feeder.

3. Put the food bowl back into the feeder. Place it carefully to avoid spilling any liquid.

4. Set the schedule for each added wet food meal in the app and close the top lid.

5. When the scheduled feeding time arrives, the rotating food section lid will open and automatically close after the pet finishes eating.

Notes:

• Please do not open the lid or change food after the feeding plans have been saved.

• The time that can be set for a single wet food meal cannot exceed 72 hours (3 days).

• By default, the rotating lid will stay open for 30 minutes during feeding times. Users can adjust this duration in the settings.

• If the pet is still eating when the feeding time is over, the safety sensor will detect it and ensure that the rotating lid continues to stay open.

1. The bottom of the feeder has a battery compartment where you can install three AA batteries (not included).

2. The backup batteries only work during a power failure. During this time, the refrigeration function will stop, but the feeding schedule within 12 hours will proceed as usual.

Note: Remove backup batteries if they are installed when the feeder is not in use for an extended period.

Food bowl cleaning:

1. End all feeding schedules of the feeder and remove the food bowl.

2. Clean the food bowl with water and wipe it dry.

Feeding zone cleaning:

Use a dry towel to wipe and clean the feeding zone.

Refrigeration zone cleaning:

Use a dry towel to wipe and clean the refrigeration zone. Note: Condensation on the bottom of the feeder is normal and occurs due to the refrigeration process.

Rotating food section lid cleaning:

1. Release the latch to remove the rotating food section lid.

2. Clean the food section lid with water and wipe it dry.

3. Use a clean towel to clean the gap between the rotating food section lid and the top lid.

Regular Cleaning of Pet Hair from Air Inlet:

The product’s air inlet may accumulate pet hair. It is recommended to clean the air inlet every 7 days.

• Do not use the feeder at temperatures below 12°C (54°F) or above 30°C (86°F).

• Do not obstruct the feeder’s cooling vents.

• Use the feeder in a dry place.

• Use the feeder on a level surface.

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation.

• Do not use the feeder with pets that are not able to reach the food bowl or with any physical disability.

• Do not immerse the base part in water at any time as it may damage electronic components.

• Do not use the feeder outdoors. Check its operation frequently to be sure it is operating properly.

• Do not disassemble the feeder other than as instructed in this user manual.

• Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.

• Do not modify the feeder.

• Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.

• To avoid tripping, always position the power cable out of the way of foot traffic.

• Power off the feeder when it’s not in use.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If the PETLIBRO POLAR PLAF109 causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.