PETLIBRO SPACE PLAF107 (01) PDF Document

The package for the PETLIBRO SPACE PLAF107 includes the following items:

1 x Automatic Pet Feeder

1 x User Manual

1 x Stainless Steel Bowl

1 x Power Cable

1 x Bowl Tray

1 x Power Adapter

The main components of the PETLIBRO SPACE PLAF107 are:

1. Lid Release Button

2. Lid

3. Silicone Strip

4. Food Tank

5. Vane

6. Rotor

7. Rotor Cover

8. Status Indicator

9. Food Tank Lock Switch

10. Air Pumping Button

11. Body

12. Stainless Steel Bowl

13. Bowl Tray

14. Reset Button

15. Speaker

16. Power Port

17. Battery Compartment

18. Battery Compartment Cover

19. Foot

20. Non-slip Pad

Follow these steps for initial installation:

1. Push the Lid Release button and remove the lid.

2. Add dry pet food to the food tank.

3. Replace the lid and push the Lid Release button to make sure the lid is securely locked.

4. Install the stainless steel bowl and bowl tray.

5. Press the Air Pumping button to pump air out of the tank.

Yes, please keep the following in mind during setup:

• If the lid is not securely locked, the feeder can’t successfully pump air out of the tank. Please make sure the two “LOCKED” markings on the Lid Release button are clearly seen without being blocked after installing the lid. If the markings are blocked, manually push the button again.

• Add dry pet food before pressing the Air Pumping button.

• After the air in the food tank is pumped out, if you don’t push the Lid Release button first, you can’t open the lid.

To power on the feeder, install four D alkaline batteries into the battery compartment for backup power. Then, connect the feeder to a wall outlet with the included power adapter and power cable.

To power off the feeder, unplug the power cable from the wall outlet and remove the batteries.

In the event of a power outage, the feeder will automatically switch to the Battery Power Mode. To ensure that the feeder can still dispense food on schedule, it’s strongly recommended to install backup batteries.

Please ensure that the feeder is always plugged into a wall outlet for power. In the event of a power outage, the PETLIBRO app will notify you. In Battery Power Mode, the feeder has a battery life of over 3 days, but the Air Pumping function cannot be used, and the food level detection function is only enabled during feeding.

1. Search for and download the PETLIBRO app from your device’s app store.

2. Open the app and follow the on-screen instructions to configure the network. The app will guide you through adding your device, either by finding it automatically or by adding it manually.

• Use the feeder in a dry place.

• Use the feeder on a level surface.

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation. Keep them away from children and pets.

• Do not use the feeder with pets that are not able to reach the food bowl or with any physical disability.

• Do not immerse the base part in water at any time as it may damage electronic components.

• Do not use the feeder outdoors. Check its operation frequently to be sure it is operating properly.

• Do not disassemble the feeder other than as instructed in this user manual.

• Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.

• Do not modify the feeder.

• Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.

• To avoid tripping, always position the power cable out of the way of foot traffic.

• Do not install or store the feeder where it will be exposed to weather or temperatures below 0°C (32°F).

• Do not use the feeder without adding pet food first.

• Power off the feeder when it’s not in use.

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Radio frequency exposure statement

To maintain compliance with the FCC’s RF Exposure Guidelines, this equipment should be installed and operated with a minimum distance of 20cm from your body.