PETLIBRO AIR PLAF008 (02) PDF Document

Please follow these safety instructions when using your PETLIBRO AIR PLAF008:

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation. Keep them away from children and pets.

• Do not use the feeder with pets that are not able to reach the food tray or with any physical disability.

• Do not immerse the base part in water at any time as it may damage electronic components like the control panel.

• Do not use the feeder outdoors. Check its operation frequently to be sure it is dispensing properly.

• Do not use wet, canned or moist food.

• Do not disassemble the feeder other than as instructed in this user manual.

• Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.

• Do not modify the pet feeder.

• Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.

• To avoid tripping, always position the power cable out of the way of foot traffic.

• Do not install or store the pet feeder where it will be exposed to weather or temperatures below 4°C (39.2°F).

• Use D alkaline batteries to power the feeder. Do not use rechargeable batteries.

• Check the batteries regularly. Before leaving for an extended period of time, always replace batteries with new ones.

• Do not lift the pet feeder by the lid, food tank, or food bowl. Lift and carry it using both hands and the base, while keeping the feeder in an upright position.

• The PETLIBRO AIR PLAF008 is suitable for dry food only, with kibble sizes ranging from 2–15mm (0.07–0.6in) in diameter. Larger kibble may get stuck at the food outlet.

• Do not put your fingers into the food outlet or let your fingers touch the rotor.

• Power off the device when it’s not in use.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• The appliance is only to be used with the power supply unit provided with the appliance.

• If the cord set is damaged, it must be replaced by a special cord set available from the manufacturer or its service agent.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (Ni-cad, Ni-MH, etc.) batteries.

The following items are included with your PETLIBRO AIR PLAF008:

• 1 x Automatic Pet Feeder

• 1 x Stainless Steel Bowl

• 1 x Bowl Tray

• 1 x Quick Start Guide

• 1 x User Manual

• 1 x Power Adapter

• 1 x Power Cable

The main components of the PETLIBRO AIR PLAF008 are:

1. Lid Release Button

2. Lid

3. Desiccant Bag Holder Lid

4. Food Tank

5. Tank Base

6. Rotor

7. LCD Display

8. Buttons

9. Food Tank Lock

10. Control Panel Cover

11. Food Outlet

12. Stainless Steel Bowl

13. Bowl Tray

14. Power Cable Slot

15. USB-C Power Port

16. Battery Compartment

17. Non-slip Rubber Pad

18. Battery Compartment Cover

The LCD display on the PETLIBRO AIR PLAF008 shows the following information:

• Battery status indicator: Lights up when batteries are installed. A blank battery status indicator means low battery level.

• STUCK indicator: Lights up when the rotor is stuck.

• LOWFOOD indicator: Lights up when the food storage level is low.

• Meal number: Displays the meal number being programmed (1-6).

• Time / Number of portions: Shows the current time or the number of portions for a scheduled meal.

• AM/PM: Indicates whether the time is before noon (AM) or after noon (PM).

The buttons on the PETLIBRO AIR PLAF008 have the following functions:

• Manual button: Press once to dispense one portion of food. You can press it up to five times rapidly at a time.

• Back/Home button: Press to go back to the previous setting. Press and hold for three seconds to go to the main interface.

• Set button: Press to confirm and go to the next setting. If you don’t press the button, your settings will not be saved.

• Up/Down buttons: Press once to select a different setting or increase/decrease the value. Press and hold for quick adjustments.

Follow these steps to set up your PETLIBRO AIR PLAF008:

1. Press the lid release button and remove the lid.

2. Add dry pet food to the food tank.

3. Replace the lid and press the lid release button.

4. Install the stainless steel bowl and bowl tray.

If you want to use a desiccant bag (not included) with your PETLIBRO AIR PLAF008, follow these steps:

1. Turn the desiccant bag holder lid counterclockwise.

2. Place your desiccant bag (size: 35*20mm / 1.4*0.79in) into one of the desiccant bag holes.

3. Replace the holder lid and turn the lid clockwise to finish installing your desiccant bag.

The PETLIBRO AIR PLAF008 feeder supports dual power modes:

• Using the power adapter and power cable: Connect the feeder to a wall outlet and it automatically turns on and the LCD display will light up in white.

• Using battery power: Install three D alkaline batteries into the battery compartment and the feeder automatically turns on.

Notes:

• Press any button to wake the display from sleep, and the display will light up in white. Make sure the display is awake before setting up.

• The LCD display will not stay on when using batteries or the power adapter.

• A battery status indicator shows up in the display after installing batteries.

• When the power adapter, power cable, and batteries are used at the same time, the feeder will only draw power via the power cable.

To power off the PETLIBRO AIR PLAF008, unplug the cable from the outlet. In battery power mode, remove the batteries from the feeder.

1. After the PETLIBRO AIR PLAF008 is powered on, press the top of the control panel cover and the cover automatically opens. Press the Set button to enter time settings.

2. Press the Set button again and the hour digit flashes.

3. Press and hold the Up/Down buttons to set the hour and press the Set button to confirm.

4. Use the Up/Down buttons and the Set button to set the minute and select from “AM” or “PM.”

5. Press the Set button to confirm.

1. After setting up the time, press the Set button to enter Meal 1 settings.

2. Use the Up/Down buttons to set the hour and minute, select from “AM” or “PM,” and set the portions.

3. Press the Set button to confirm the Meal 1 settings.

4. After setting up Meal 1, the feeder automatically goes back to the main interface. Press the Set button, the meal number “2” flashes, and press the Set button again to enter Meal 2 settings. Use the Set button to set up Meals 3-6. If you want to set fewer than 6 meals, use the Up/Down buttons to select and customize a specific meal when one of the meal numbers flashes.

5. After setting up, replace the cover and push it in.

Notes:

• The maximum number of portions per meal is 16.

• To successfully set up a meal, make sure the portion is not set as 0 and press the Set button to confirm after setting. All successfully set meals will be displayed on the screen.

The recommended feeding portions for the PETLIBRO AIR PLAF008, with one portion being 1/24 cup (10.4ml), are as follows:

To reset the PETLIBRO AIR PLAF008 to factory settings, press and hold the Up button and the Down button for three seconds.

When the PETLIBRO AIR PLAF008 is powered on, press the Manual button once and the feeder will dispense one portion of food. You can press the Manual button up to five times and the feeder will dispense five portions of food.

1. Pull the food tank locks outwards.

2. Lift the food tank cover.

3. Hold the tank base, turn the rotor clockwise, and lift the rotor.

4. Clean and air-dry the rotor and food bowl.

• Power off the device before cleaning.

• Clean the food bowl with tap water.

• Do not clean the feeder in a dishwasher. Only the stainless steel bowl is dishwasher safe.

• Use a soft damp cloth to clean the feeder base. Do not wash any part with electronic components.

• Replace the desiccant bag every half a month to keep food fresh.

• If a blank battery status indicator shows on the display, please replace the batteries.

• If there is a “LOWFOOD” indicator, refill the food tank.

• If there is a “STUCK” indicator, disassemble the tank base and remove any food that’s stuck in the rotor.

• If the feeder is not dispensing food, make sure you have filled the tank with enough food.

• If the feeder won’t turn on, check if the power adapter, power cable, or batteries are correctly installed.

• Please make sure the food in the tank is dry, and food size is within 2-15mm (0.07-0.6in) in diameter.

• If the food won’t come out, remove the food tank and tank base, and check if the chute inside is blocked.

• If the food won’t come out, check whether the battery level is low, whether the power adapter is connected, and whether a power outage occurs when the power adapter is connected but batteries are not installed.

• The first few portions may vary, but it doesn’t mean it’s faulty. After about 6 feedings, it should be almost even.