PETLIBRO EASY FEED PLAF004 (01) PDF Document

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation; keep away from children and pets.

• Do NOT allow small children to play with, in or around the pet feeder.

• To reduce the risk of injury, please keep close supervision when an appliance is used near children.

• Do NOT use the feeder with pets not able to reach the food tray or with any physical disability.

• Do NOT immerse the base part in water at any time as it may damage electronic components like the control panel.

• Do NOT place any foreign object in the pet feeder.

• Do NOT use outdoors. Check operation frequently to be sure the unit is dispensing properly.

• Do NOT use wet, canned or moist food.

• Do NOT disassemble the unit other than as instructed in this User Guide.

• Do NOT use the feeder for anything other than its intended use.

• Only use attachments recommended or sold by the manufacturer. The use of attachments not recommended or sold by the manufacturer may cause an unsafe condition. Do not modify the pet feeder.

• Do not operate any appliance if the unit is malfunctioning or has been damaged. Do not attempt repairs on the pet feeder yourself.

• Always unplug when not in use and before cleaning.

• Never pull on the electrical power cord to remove the plug from the wall outlet.

• If the plug of this device gets wet, turn on electricity to that wall outlet. Do not attempt to unplug.

• Examine the feeder after installation. Do not plug in if there is water on the power cord or plug.

• To avoid tripping, always position power cord out of the way of foot traffic.

• Do NOT allow pets to chew on or swallow any parts. If you are concerned about the power cord, purchase a cord conduit (a hard-plastic protector) at any hardware store to protect the power cord.

• If an extension cord is necessary, one unit with a proper rating should be used.

• Do NOT install or store the pet feeder where it will be exposed to weather or temperatures below 4°C / 40°F.

• Use alkaline D batteries to power. Do NOT use rechargeable batteries.

• Check the batteries regularly. Before leaving for extended time, always replace batteries with new ones.

• Do NOT lift the pet feeder by lid, food tank, or food tray. Lift and carry it using both hands and the base, while keeping the unit in an upright position.

• Suitable for dry food ONLY, with kibble size ranging from 2-15mm / 0.07-0.6in in diameter. Larger kibble may get stuck at the food outlet.

• Read and observe all important notices listed on the pet feeder and in the packaging.

Front View:

1. Lid

2. Lid Lift

3. Food Tank

4. Indicator Light

5. Microphone

6. Control Panel

7. Base

8. Food Outlet

9. Food Tray

10. Low Food Storage Sensor

11. LCD Display

12. Anti-Clog Detector

Bottom View:

13. Power Socket

14. Battery Compartment

15. Power Switch

16. Speaker

*Note:

1) About 0.06cup/1tbsp/15ml per portion.

2) Keep press the Record Button during recording.

Open the battery compartment at the bottom of the feeder. Insert the Micro USB power cord into the connector on the bottom and extend the power cord out along the designed wire slot. Close the battery compartment. Turn on the power switch.

The LCD display will light up automatically indicating the feeder is on now.

Note:

1) Battery NOT included.

2) Before connecting to power, make sure all parts are clean and completely dry.

3) You could also put in 3 pieces of D cell batteries, so that the feeder can still work according to your scheduled feeding plan even during outage.

4) The battery level icon on the display blinks on a low battery level.

Place the feeder in a desired location. Check the food tank is in place. Place the feeding tray into the feeder from the front.

Please set the current time before setting up feeding plan.

1. Long press the Setting Button for 3 seconds, the Time Setting icon will start to flash, which means it is in settings mode.

2. Press Confirm/OK Button to confirm and enter the time setting. The hour will flash. Use the Up/Down Buttons to set the hour (24H format). You can long press the Up/Down Button for fast setting.

3. Press Confirm/OK Button to confirm the hour. Then the minute starts to flash, press the Up/Down Button for minute setting.

4. Then press Confirm/OK Button to save and return to setting mode. Press Return/Cancel Button to exit or go on to set up other items.

Note: All operations during the setup process can be returned or canceled via the Return/Cancel Button.

In the standby state, you can quickly feed 1 portion by pressing the down Button twice within 1 second.

To set “feed now” for multiple portions:

1. Long press Setting Button for 3 seconds to enter the setting mode.

2. Press Down Button to switch the flashing icon to the feeding one.

3. Press Confirm/OK Button to confirm and manually choose the feeding portions.

4. Use the Up/Down Button to choose the number of portions.

5. Press Confirm/OK Button to start feeding. The operation screen will display the exact remaining portions to be fed.

The PETLIBRO EASY FEED PLAF004 supports up to 6 meals per day.

1. After setting up the current time, press and hold Setting Button for 3 seconds to enter the feeding plan setting mode.

2. Press Down Button to switch the flashing icon to Digital 1 icon.

3. Press Confirm/OK Button to select the feeding portions, press Up/Down Button to set portions.

4. Press Confirm/OK Button to go to feeding time setting, Press Confirm/OK Button to save. Press Return/Cancel Button to exit and the auto feeding icon will show at standby state.

If you need to set multiple meals, please repeat the above steps and select the corresponding Digital number icon according to the meals in the setting interface.

To cancel a certain meal, you can set the feeding portions to be 0.

1) About 0.06cup/1tbsp/15ml kibbles are dispersed each portion.

2) A few kibbles may be left at the chute after feeding, and it may come out of the outlet when the machine is moved (doesn’t indicate faulty equipment).

3) Refer to the instructions on your pet food packaging for detailed feeding instruction.

• Press and hold the Record Button for 3 seconds until the feeder makes a “Beep” sound to start recording. After the recording is completed. The feeder will make a double “Beeps”.

• After recording, you can preview the audio by short pressing the Record Button. Repeat above if need to re-do the recording. The closer to the microphone, the louder the voice can be recorded.

• The default of voice recording playback is 3 times. It can be customized up to 5 times at the setting by taking the following steps:

1. Press and hold the Setting Button for 3 seconds to enter the setting mode.

2. Select the Down Button to switch the flashing icon to Record Button.

3. Press Confirm/OK Button to confirm play times of recording playback by using the Up/Down Buttons. Press Confirm/OK Button to save.

Note:

1) The recording Button should be pressed during the recording.

2) The maximum record time is 10 seconds.

3) To cancel the feeding recording, set the number of playback to 0.

4) When batteries as the only power source, for the purpose of power saving, the voice call will only play 1 time before dispensing.

• When the battery is low, the screen will display a low battery signal.

• When the food is insufficient, the screen will display the low food storage icon.

• When these two cases happened together, the Indicator light will be in a red breathing light.

• After renewing the battery or re-filling food, the red Indicators and screen icons will disappear automatically within 60 seconds.

In the standby state, press and hold the Setting Button and Confirm/OK Button at the same time for 3 seconds until the feeder makes a short beep. You can reset the feeder to factory default.

It’s recommended to clean the feeder regularly for the health of your pet. The washable parts of the Petlibro auto feeder are the food tank and food tray. They can be submerged in water. Clean by hand-washing using cool or warm soapy water.

Dissembling the food tank:

• If you have food inside the tank or chute, double press the Down Button and repeat for a few times to empty first.

• Push the tank upward to disassemble.

Dissembling the food tray:

• Empty the tray, pull it to remove from the base.

Note: Rinse and let all parts air dry completely before assembling.

The screen may be locked. Please press and hold the Setting Button for 3s to enter the setting mode and unlock it.

Unlock the screen, press the Set Button and you can see the meal number shown. Enter each meal, you can review all the meal time and portion settings.

1) Please be sure to fill in with dry food; kibble size should range from 2-15mm / 0.07-0.6in in diameter.

2) Check whether any foreign objects are placed, disassemble the food tank and check the chute. Also check the food outlet.

3) Check whether it’s low battery level – whether the power adapter is connected or there is any outage when no battery is installed.

1) Please press and hold the Setting Button for 3s to unlock the screen.

2) Check whether the power adapter is connected.

Please follow the steps outlined in the Cleaning & Care instructions for disassembly.

The first few portions may vary, and it doesn’t mean a faulty equipment. After about 6 feedings it should be almost even.