PETLIBRO ONE RFID PLAF301 (01) PDF Document

Please follow these safety instructions when using your PETLIBRO ONE RFID PLAF301:

• Use the feeder in a dry place.

• Use the feeder on a level surface.

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation. Keep them away from children and pets.

• Do not use the feeder with pets that are not able to reach the food bowl or with any physical disability.

• Do not immerse the base part in water at any time as it may damage electronic components.

• Do not use the feeder outdoors. Check its operation frequently to be sure it is operating properly.

• Do not disassemble the feeder other than as instructed in this user manual.

• Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.

• Do not modify the feeder.

• Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.

• To avoid tripping, always position the power cable out of the way of foot traffic.

• Do not install or store the feeder where it will be exposed to weather or temperatures below 0°C (32°F).

• Do not use the feeder without adding pet food first.

• Power off the feeder when it’s not in use.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• The appliance is only to be used with the power supply unit provided with the appliance.

• If the cord set is damaged, it must be replaced by a special cord set available from the manufacturer or its service agent.

• This feeder is for dry food only. Do not use it for wet food, pet supplements, or medicine.

The following items are included with your PETLIBRO ONE RFID PLAF301:

• 1 x Automatic Pet Feeder & Food Tank

• 1 x Stainless Steel Food Bowl with Holder

• 1 x Power Adapter

• 1 x User Manual

• 1 x Food Bowl Lid

• 2 x Food Bowl Shield

• 1 x Quick Start Guide

• 1 x Collar Tag

• 1 x RFID Reader

• 1 x Desiccant Bag

The PETLIBRO ONE RFID PLAF301 consists of the following components:

1. Food Tank Lid

2. Desiccant Bag Holder

3. Food Tank

4. Infrared Sensor A (Detects pet)

5. Control Panel

6. Infrared Sensor B (Detects food levels)

7. LED Display

8. Feeder Base

9. Food Bowl Lid Pivot Lock

10. Food Outlet

11. Infrared Sensor C (Detects food blockages)

12. Food Bowl Shields

13. Food Bowl Lid

14. Stainless Steel Food Bowl

15. Bowl Tray

16. RFID Reader

17. RFID Reader Prongs

18. Battery Compartment

19. Battery Compartment Cover

20. Speaker

21. Power Port

22. Food Tank Lock

Follow these steps to assemble your PETLIBRO ONE RFID PLAF301:

1. Install the food bowl lid:

• Press the locks on both sides of the food tank lid, remove the lid, and take out the accessories from the food tank.

• Install the food bowl lid in the direction shown in the figure.

• After successfully installing the food bowl lid, move the food bowl lid pivot lock to the left to ensure that it’s in the locked state. Note: If the food bowl lid is unlocked, the product will not work properly.

2. Install the body:

• Place the RFID reader on a flat surface, keeping it close to the power port and away from metal objects. Note: The RFID reader is not waterproof.

• Place the stainless steel food bowl and bowl tray in the designated groove of the reader.

• Open the battery compartment at the bottom of the feeder. Install three alkaline D batteries (not included) in case of a power outage. Notes: Batteries are not included. To avoid sudden power outages, do not use batteries as the only power source; they are for an emergency plan. To avoid battery leakage, remove the batteries if the device won’t be in use for a period of time. When in battery mode, only the RFID recognition, Wi-Fi, and feeding functions are enabled.

• Plug the USB cable into the power port at the bottom of the feeder.

• Place the body in the designated position on the reader. If you hear a ‘click’ sound, the body is properly installed.

3. Install the food bowl shields:

• Insert both shields into the body.

4. Install the food tank:

• Press the food tank lock to lock it in place.

5. Add dry pet food to the food tank:

• To prevent uneven food dispensing and low food alarms, add enough pet food. Recommended kibble size is 2-15mm (0.07-0.6in) in diameter. Do not use canned, wet, or moist food.

6. Put the food tank lid on:

• Remove the desiccant bag from packaging and place it in the holder under the food tank lid. It is recommended to change the desiccant bag every 14 days to prevent mold growth. Remove the bag before cleaning the lid.

• Press the locks on both sides of the food tank lid to install the lid in place.

7. Connect Power:

• Plug the 5V power adapter into a power outlet.

• The indicators will light up automatically to indicate the feeder is on.

To prevent potential interference, the distance between multiple PETLIBRO ONE RFID PLAF301 feeders should be more than 10 inches / 25 cm.

1. Download and install the PETLIBRO app. Note: There are two similar apps available on your phone’s app store: PETLIBRO and PETLIBRO LITE. Please make sure to download the “PETLIBRO” app (not “PETLIBRO LITE”).

2. Follow the instructions to configure the network.

There are two methods to pair the collar tag: sensor-based pairing and QR code-based pairing. If one method fails, you can switch to the other.

1. After successfully adding the device in the app, tap the “ADD COLLAR” button.

2. Place the collar tag in the RFID recognition area, as close to the RFID reader as possible.

3. After a successful addition, tap “CONFIRM” to pair the collar tag.

4. Follow the app instructions to add relevant pet information.

• Power off the device before cleaning.

• Do not clean the feeder in a dishwasher. Only the stainless steel bowl is dishwasher safe.

• Use a soft damp cloth to clean the feeder base. Do not wash any part with electronic components.

• Replace the desiccant bag every 14 days to keep food fresh.

To power off the PETLIBRO ONE RFID PLAF301, unplug the cable from the outlet and remove the batteries.

This PETLIBRO ONE RFID PLAF301 complies with Part 15 of the FCC Rules and is designed to provide reasonable protection against harmful interference. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The PETLIBRO ONE RFID PLAF301 is classified as waste electrical and electronic equipment (WEEE) and should not be mixed with unsorted household waste. To protect human health and the environment, you should hand over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.