PETLIBRO GRANARY PLAF203 (01) PDF Document

The following items are included with the PETLIBRO GRANARY PLAF203:

• 1 x Automatic Pet Feeder

• 1 x Food Bowl with Holder

• 1 x Power Adapter

• 1 x Desiccant Bag

• 1 x User Manual

• 1 x Quick Start Guide

The main components of the PETLIBRO GRANARY PLAF203 are:

1. Lid

2. Sealing Strip

3. Food Tank

4. Transparent Window

5. Tank Base

6. Anti-Clog Detector

7. Camera

8. Infrared Light

9. Control Panel

10. Display Panel

11. Food Outlet

12. Feeder Base

13. Stainless Steel Bowl

14. Bowl Holder

15. Desiccant Box

16. Power Jack

17. Power Adapter

18. Battery Compartment

19. SD Card Slot

20. Compartment Lid

21. Speaker

Follow these steps to set up your PETLIBRO GRANARY PLAF203:

1. **Installation:** Take out the food bowl from inside the food tank. Twist the lid anticlockwise to remove it. Pull the notches on both sides of the food tank outward slightly and then lift up to remove the food tank from the base.

2. **Insert SD Card (optional):** To enable video recording, insert a standard SD card (16-256GB, Class 10 or above). Open the battery compartment at the bottom of the feeder; the slot is in the middle. Insert the card in the direction shown until it clicks. After insertion, enable the recording function in the app.

3. **Connect Power:** Plug the 5V power adapter into a socket and the USB cable into the port on the back of the feeder. The indicators will light up. For backup power, open the battery compartment and install three alkaline D batteries (not included), matching the polarity markings.

4. **Place Desiccant Bag:** Place the desiccant bag into the inner box under the lid. It is recommended to change the bag every 15 days.

5. **Install Food Tank:** Align the food tank with the notches on both sides of the tank base and place it down.

6. **Add Pet Food:** Add dry pet food to the tank. Ensure you add enough food to reach the visible level to prevent uneven dispensing. Recommended kibble size is 2-15mm (0.07-0.6 inch) in diameter. Do not use canned, wet, or moist food.

7. **Replace Lid:** Put the lid back on and turn it clockwise to lock it into place.

8. **Install Food Bowl:** Attach the bowl to the designated notches underneath the feeder base.

To enable the video recording function on your PETLIBRO GRANARY PLAF203, first insert an SD card, then enable the recording function in the app by tapping the icon in the upper right corner > Device Camera > Video Settings.

1. Open the battery compartment at the bottom of the feeder. The SD card slot is located in the middle of the battery compartment.

2. Insert the SD card in the direction shown. Slide it in until it clicks into place. Do not use excess force when inserting the card.

To remove an SD card, push the card in lightly and it will pop out.

The PETLIBRO GRANARY PLAF203 supports standard SD cards (such as Samsung and SanDisk) with a capacity of 16-256GB and a speed of Class 10 or above. Before first use, please use the app to format the SD card in Settings. For privacy reasons, video files on the SD card can only be viewed through the Replay section of the app and cannot be read by a PC or phone.

• Batteries are not included. The feeder requires three alkaline D batteries for backup power.

• To avoid sudden power outage affecting your pet’s feeding, do not use batteries as the only power source. Batteries should only be used as an emergency plan.

• To avoid battery leakage, remove the batteries if the device will not be in use for a period of time.

• When the feeder is powered only by batteries, the WiFi function, camera function, record button, and reset button will be disabled to extend the working time. Meal schedules will be carried out normally.

• To prevent uneven food dispensing, please add enough pet food to the visible level.

• The recommended kibble size is 2-15mm / 0.07-0.6 inch in diameter.

• Do not use canned, wet, or moist food in the feeder.

1. Download and install the PETLIBRO app from your phone’s app store. Note that there are two similar apps available: PETLIBRO and PETLIBRO LITE. Please make sure you download the correct one (PETLIBRO).

2. Follow the instructions within the app to configure the network and connect your feeder.

It is recommended to clean the feeder regularly. The washable parts are the lid, food tank, tank base, stainless steel bowl, and bowl holder. Clean other parts with a dry cloth.

To clean the tank lid, food tank, and tank base:

1. Disconnect the power before cleaning. Ensure the food tank is empty to avoid spilling.

2. Twist the lid anticlockwise to remove it and take out the desiccant bag from the inner box.

3. Pull the notches on both sides of the food tank outward slightly and then lift up to remove it.

4. Twist the tank base anticlockwise to remove it from the feeder base.

5. Thoroughly rinse and air dry the lid, tank, and tank base.

6. Refit the parts to the machine. Turn the tank base clockwise until it snaps into place.

7. Install the tank and lid.

To clean the food bowl:

1. Press down on the food bowl with its holder to remove them from the feeder base.

2. Rinse and air dry them thoroughly before refitting them to the machine.

1. Keep the feeder and your phone close to your router to ensure the network signal is good.

2. Restart the feeder.

3. Follow the APP’s instructions or operation videos to add the feeder. There is more than one method available to add the device.

1. Keep the feeder close to your router and make sure the network signal is good. It is ideal to have it within 6m (19.7ft) without obstacles and walls.

2. Make sure the power cord is connected firmly.

3. Restart the feeder.

Press and hold the Unlock Button for 5 seconds to unlock the buttons. The control panel automatically locks after 30 seconds of standby.

1. Make sure the food in the tank is dry and the kibble size is within 2-15mm (0.07-0.6in) in diameter.

2. Remove the food tank and tank base, then check if the chute inside is blocked.

3. Check if the anti-clog detector at the food outlet is dirty or blocked.

4. Check the battery level. Also, check if the power adapter is connected and if there has been a power outage.

1. Check if the electricity is cut off.

2. Check if the indicator lights function has been turned off in the App.

Pull the notches on both sides of the food tank outward a little and then lift up to remove the food tank.

The first few portions may vary, but this does not mean the appliance is faulty. After about 6 feedings, the portion amount should be almost even.

1. Make sure the feeder is ready for network connection; the WiFi indicator on the feeder should be flashing.

2. Hold your phone about 6-8 inches away from the feeder’s camera. You may need to remove the food bowl and tilt the feeder as needed.

1. Switch to a stronger WiFi signal.

2. If the network is poor, change the video quality from HD (high definition) to SD (standard definition) in the app.

1. The screenshots and manually recorded video clips are stored in the Album section of the app.

2. The video playbacks from the SD card are stored in the Replay section of the app.

Night Vision is set to Auto by default. The infrared light will automatically turn on when it is dark, and the real-time video stream will appear in black and white. Night vision turns off when there is enough ambient light.

You can manually select the night vision to Auto/Always On/Always Off. Tap the icon in the upper right corner of the camera view, then select IR Night Vision.

When motion is detected, your phone will receive a notification.

1. To enable motion detection, tap the icon in the upper right corner of the camera view, then go to Detection Alarm Settings > Motion Detection Alarm.

2. The camera can automatically record a video clip when motion is detected. Tap the icon in the upper right corner > Recording Settings > Recording Mode > Event Recording.

3. To ensure your phone can receive notifications, enable the PETLIBRO App notifications on your phone first.

When sound is detected, your phone will receive a notification.

1. To enable sound detection, tap the icon in the upper right corner of the camera view, then go to Detection Alarm Settings > Sound Detection Alarm.

2. To ensure your phone can receive notifications, enable the PETLIBRO App notifications on your phone first.

• Use the feeder in a dry place.

• Use the feeder on a level surface.

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation.

• Keep them away from children and pets.

• Do not use the feeder with pets that are not able to reach the food bowl or with any physical disability.

• Do not immerse the base part in water at any time as it may damage electronic components.

• Do not use the feeder outdoors. Check its operation frequently to be sure it is operating properly.

• Do not disassemble the feeder other than as instructed in this user manual.

• Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.

• Do not modify the feeder.

• Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.

• To avoid tripping, always position the power cable out of the way of foot traffic.

• Do not install or store the feeder where it will be exposed to weather or temperatures below 0°C (32°F).

• Do not use the feeder without adding pet food first.

• Power off the feeder when it’s not in use.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Radio frequency exposure statement

To maintain compliance with the FCC’s RF Exposure Guidelines, this equipment should be installed and operated with a minimum distance of 20cm from your body.