PETLIBRO CAPSULE PLWF008 (01) PDF Document

Please adhere to the following safety warnings when using the PETLIBRO CAPSULE PLWF008:

• Dispose of all packaging materials properly. Keep polybags away from children and pets as they can cause suffocation.

• Do NOT allow children to play with, in, or around the pet water fountain.

• To avoid injury, please keep close supervision when the appliance is used near children.

• Do NOT use the water fountain with pets not able to reach the water tray or with any physical disability.

• Do NOT place any foreign object in the water tank.

• Do NOT disassemble the pet fountain other than components as instructed in the User Manual.

• Do NOT use the pet fountain for anything other than its intended use.

• Only use attachments recommended or sold by the manufacturer.

• Do NOT modify the pet fountain.

• Do NOT operate any appliance if the unit is malfunctioning or has been damaged. Do not attempt repairs on the device yourself.

• This product is for indoor use only.

• This product is not allowed to run without water.

• Do not use the appliance in the bathroom.

• DO NOT put the fountain into the dishwasher, otherwise, there is a risk of deformation.

• Be sure to disconnect the power supply for safety when the appliance is not in use.

• Please disconnect the power supply before maintaining and cleaning the machine.

• Always unplug the appliance when not in use, or before putting on or taking off parts and before cleaning.

• The power adapter and wire plug must not be flooded during cleaning.

• Never pull the electrical power cord to remove the plug from the wall outlet.

• If the plug of this device gets wet, turn off the electricity of that wall outlet. Do NOT attempt to unplug.

• Check the device after installation. Do NOT plug in if there is water on the contact points or plug.

• To avoid tripping, always position the power cord out of the way of foot traffic.

• The appliance is only to be used with the power supply unit provided with the appliance.

• If the cord set is damaged, it must be replaced by a special cord set available from the manufacturer or its service agent.

• Do NOT allow pets to chew on or swallow any parts. If you are concerned about the power cord, purchase a cord conduit (a hard-plastic protector) at any hardware store to protect the power cord.

• If an extension cord is necessary, one unit with a proper rating should be used.

• Do NOT install or store the pet water fountain where it will be exposed to weather or temperatures below 0°C / 40°F.

1. Soak the filter in a clean bowl for 5 minutes, then rinse the filter thoroughly with tap water. Note that the filter must be fully soaked before the fountain is turned on; otherwise, water may not flow smoothly and cause spillage. Do not soak the filter in the water tank of the fountain to avoid surface dust.

2. Insert the foam filter into the groove of the water pump. Position the pump according to the bottom slot shape. Ensure you align the recessed part of the pump with the protruding part of the water tank for a firm installation.

3. Insert the water pump’s USB cable through the hole at the back of the water tank, starting from the inside and extending outward.

4. Clip the wire into the anti-pull slot.

5. Plug the USB into the power adapter.

6. Install the silicone pipe on the pump. Add water to the tank.

7. Fit the filter tray onto the bottom of the serving tray base. When installing, ensure to rotate the filter tray until it aligns with the serving tray base.

8. Place the soaked filter into the filter tray.

9. Install the serving tray onto the serving tray base.

10. Install the serving tray, serving tray base, filter, and filter tray into the water tank. The serving tray features a water outlet that should be positioned closer to the rear of the product. Press down until the indicator line on the water tank’s rear inner wall is aligned to ensure parts snap into place securely for smooth water flow.

11. Connect the power adapter. The water fountain will initiate its ‘self-cleaning mode’ every six hours, intermittently flushing the serving tray with water.

1. Replace the filter and the foam filter at least once every 2 weeks.

2. Clean the pump and fountain at least once every week.

1. Remove the foam filter, pump cover, and impeller cover in sequence. Note: The foam filter can affect water flow, so please clean it regularly and replace it promptly when cleaning the pump.

2. Remove the impeller by hand.

3. Use the provided brush to clean the parts with water.

Tip: The brush can also be used to clean the spout. It is recommended to clean the spout every 2 weeks.

1. Fill the water tank with water between the MIN and MAX lines. The pump will fail if it runs dry.

2. Clean the pump, water tank, and serving tray.

The filters absorb more water (and therefore clean more water) when they’re wet and expanded. Soaking the filter also removes particulate matter that may have settled on the filter.

1. For the first use (or reuse after long-term storage), the water pump needs to discharge air. It’s normal if the water output speed slows down temporarily.

2. If there is dirt in the pump, please refer to the “How to Clean the Pump” section in the manual to clean it.

Please ensure that the power supply is connected, and that the water pump and base are installed correctly. Please refer to the “How to Use” section of the manual for proper installation instructions.

1. Please ensure that clean water sources are replaced regularly.

2. Please make sure to soak and wash the filter element in advance before use.