PURE AIR5 (01) PDF Document

The PURE AIR5 package contains the following items:

1x PURE AIR5 (or Pure Air⁵ Pro)

1x Charger

1x User manual

1x Allen key (3mm)

4x M5 countersunk bolts

Follow these steps to set up your new PURE AIR5:

1. Set up in box: Keep the e-scooter within the opened box during setup to keep it firmly in place.

2. Raise the stem: Remove any remaining protective packaging, then unfold the stem to its upright position, making sure the latch is down.

3. Secure the latch: Lift the latch mechanism until it clips securely into the stem. Do not ride the scooter if the latch is loose.

4. Lift the handlebar: Lift the handlebar onto the stem, ensuring the internal wires are not trapped and the external brake cable is not twisted.

5. Fix the handlebar: Rotate the handlebar to align the holes in the stem with the handlebar. Insert the stem bolts loosely into the recesses.

6. Tighten the bolts: Use the supplied Allen key to tighten the bolts. Do not tighten each screw all the way in one go.

7. Fully charge: Charge your e-scooter until the charger status light changes from red to green.

8. Tyre pressure: Check that the tyres are inflated to the optimum pressure of 36 PSI / 2.5 Bar. Always use the valve extender with your pump to avoid damaging the tyre valves.

1. First, turn on your PURE AIR5 by pressing and holding the central multifunction button for 2 seconds. The display will switch on.

2. To start riding, lift up the kickstand, place one foot on the deck and push against the floor with your other foot to propel you forwards.

3. After you’ve pushed yourself forwards, press the throttle with your thumb steadily to start accelerating. You need to achieve a speed of 3km/h before the throttle will engage.

4. Steer by turning the handlebars left and right. The steering mechanism is spring-loaded to help it return to centre.

5. You can slow down the e-scooter by pulling the brake lever. Braking activates both the electrical rear brake and the front drum brake.

6. To come to a stop, slow to almost a standstill. Then, place one foot on the ground, leaning slightly onto that foot as you come to a complete stop.

Use your right thumb to operate the throttle.

Use your left hand for the brake and indicators.

Switch on the PURE AIR5 and double press the multifunction button to select your riding mode.

Using the Pure app with your PURE AIR5 allows you to unlock additional features:

Lock: Lock your e-scooter to prevent unauthorised use. The default PIN is 888888; please change this to something unique and memorable.

Change Units: Change the units for the speedometer between km/h and mph.

Cruise Control: Turn on Cruise control. This allows you to release the throttle while riding on longer journeys.

Keep your tyres inflated: Your tubeless tyres naturally leak air pressure over time. Pump up your tyres to 36psi / 2.5 bar before each ride to get fewer punctures and better performance.

Maximise your e-scooter range: To maximize your battery range, follow these steps:

1. Fully charge your new e-scooter until the light on your charger goes green.

2. Try to ride it until the battery is nearly empty.

3. Then fully re-charge the battery back to 100%.

Ride safely & responsibly: Wear a helmet, use your lights and indicators (on selected models), and respect local laws.

Select your maximum speed: Double press the power button to cycle through the 3 speed modes (indicated by the ‘S’ on screen).

Regular maintenance: Maintaining your PURE AIR5 regularly helps reduce the risk of issues.

Turn on/off: Long press the multifunction button for 2 seconds. The scooter turns off automatically after 5 minutes of inactivity.

Headlights on/off: Short press the multifunction button.

Change drive mode: Double press the multifunction button to cycle through the 3 drive modes (Normal, High, Pedestrian).

The display shows the following information:

Mode: Indicates the current drive mode.

Left/Right Indicator: Flashing arrows indicate active turn signals.

Speed: Shows the current speed in large digits.

Bluetooth: Indicates if the scooter is connected to the app.

Headlight: Shows if the headlight is on.

Cruise Control: Indicates when cruise control is active or enabled.

Unit of speed: Shows whether the speed is in km/h or mph.

Battery: Shows the remaining battery level with five bars.

The PURE AIR5 has three drive modes, which you can cycle through by double-pressing the multifunction button. The chosen mode is saved when the scooter is turned off.

Cruise control is turned off by default and must be enabled via the mobile app. When enabled, the cruise control icon flashes white on the display.

To activate it, hold the throttle at a constant speed for 5 seconds. The icon will show solid white and two beeps will occur. Your PURE AIR5 will then maintain a constant speed when you release the throttle.

To deactivate cruise control, press the brake or throttle. This will be signalled by a single beep.

The remaining battery charge level is indicated by a status bar under the speed display, which is split into five bars:

5 Bars: 100 – 81%

4 Bars: 80 – 61%

3 Bars: 60 – 41%

2 Bars: 40 – 21%

1 Bar: 20 – 11%

1 Bar (Flashing): 10 – 0%

Before charging your PURE AIR5:

If you notice any damage on the charger or cables, do not use it.

Only use the original charger provided with the e-scooter or a genuine replacement.

Allow the scooter to cool down before charging.

1. Fully charge the battery before riding the e-scooter for the first time.

2. The maximum charging voltage is 42V DC, 3A.

3. While charging, all normal e-scooter functions are disabled. When you press the multifunction button, a charging battery indicator will show.

4. When the light on the charger changes from red to green, the charge cycle has completed.

5. Unplug the charger when charging is finished.

Only charge the e-scooter in temperatures between 5°C and 40°C.

Always charge the battery in a dry and clean environment, out of direct sunlight.

Always charge the e-scooter in a safe and well-ventilated area (e.g. away from flammable materials, children and pets). If possible, store in a garage or shed.

Do not leave the e-scooter unattended while charging.

Never charge the product while you are asleep.

Never store or charge your scooter in fire escape routes.

If your PURE AIR5 exhibits any of the following signs: Smoke, Excessive Heat, Burning Smell, Hissing or Crackling Sounds, Leaking/Bulging; follow these steps:

1. Stop using immediately.

2. If safe, disconnect the charger and remove the scooter from your home.

3. Evacuate and contact emergency services.

The PURE AIR5 is waterproof to an IP65 rating. You may use the e-scooter in the rain and ride through puddles, but should avoid partial or total submersion.

6: Totally dust tight. Full protection against dust and other particulates.

5: Protection against low-pressure jets (6.3mm) of directed water from any angle (limited ingress permitted with no harmful effects).

Before you ride your PURE AIR5 each time:

Check that all screws and bolts are tight, especially those of the handlebar, the hinge, the brakes and the front and rear wheel.

Check your tyres and pressures, ensuring that they’re in the optimum range stated on the side of the tyre wall (between 36-50psi).

When you brake, your e-scooter uses regenerative braking on the rear wheel. However, if your battery is fully charged, regenerative braking is reduced. Always ensure the drum brake on the front wheel is properly adjusted before you set off.

Store the PURE AIR5 in a dry place, away from direct sunlight. If left unused, recharge the battery every month to maintain longevity. Never store the e-scooter in temperatures above 50°C, or below -20°C, as this will cause damage.

To avoid corrosion, you should clean and dry your e-scooter after every use.

Use a slightly damp sponge or cloth for cleaning and dry afterwards with a towel.

DO NOT use excessive water or harsh substances such as degreasers as they may result in damage.

NEVER use a pressure washer to clean the e-scooter.

Sometimes your PURE AIR5 may enter a deep sleep mode. To awaken it, fully charge your e-scooter:

1. Plug the charger into your e-scooter; the charger light should change from green to red.

2. Charge your e-scooter fully. When the light on the charger changes from red to green, the charge cycle has completed.

1. Check the brakes, wheels and tyres before every ride. Never ride with damaged brakes. The brake lever activates both the drum front brake and the electric brake of the rear wheel. Be aware that braking distances may be extended in wet weather.

2. Before each ride, ensure the steering system is working and that the latch for the folding mechanism is in place correctly, with the handle firmly tightened.

3. Wear flat closed shoes when using the e-scooter. Always keep both feet on the e-scooter while riding, unless you are just starting to accelerate or about to stop. Wait until you have come to a complete standstill before you get off the e-scooter.

4. We recommend wearing protective equipment (e.g. helmet, kneepads, etc.) when riding the e-scooter.

5. Hold the handlebar firmly with both hands at all times when riding.

6. It is your responsibility to ride the e-scooter using good judgement in order to reduce the risk of injury. Do not use the e-scooter when under the influence of drugs, alcohol or medication that may impair your judgement.

7. The e-scooter is designed for outdoor use on smooth, stable surfaces. You should ride appropriately for the conditions you are riding in, and anticipate potential hazards at all times.

8. Both tyres must be in contact with the ground at all times in order to be able to provide adequate grip to ride safely (conditions permitting).

9. If your e-scooter breaks or shows wear, we strongly recommend having a service carried out.

Additional Safety Information:

Always keep the e-scooter away from humidity in excess of 90%.

Do not attempt to turn off the e-scooter while you are riding.

Take extra caution when using the e-scooter in the dark.

Avoid overcrowded areas.

Notify your presence when approaching a pedestrian or cyclist when you are not seen or heard. This e-scooter is fitted with a bell for this purpose.

Dismount your e-scooter when entering a pedestrian zone and cross the protected passages while walking.

This vehicle is not intended for acrobatic use.

Regularly check the tightness of the various bolted elements, in particular the wheel axles, the folding system, the steering system and the brake system.

Eliminate any sharp edges caused by use.

The kickstand must be folded up before stepping onto the scooter. Never step on the mudguards.