MOUNT-IT MI-2789N (01) PDF Document

Please read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

• Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.

• Safety gear and proper tools must be used. This product should only be installed by professionals.

• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

• Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

• This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.

The MOUNT-IT MI-2789N supports the following specifications:

• VESA Patterns: 75×75 and 100×100

• Maximum Screen Size: 27 inches

• Rated Weight Capacity: 7kg (15.4lbs) per monitor, for a total of three monitors.

Check that the bracket is secure and safe to use at regular intervals (at least every three months).

The following components are included:

• A (x3) – VESA Plate

• B (x1) – Pole

• C (x1) – Base

• D (x1) – Left Arm

• E (x1) – Right Arm

• F (x1) – Center VESA Mount

• G (x3) – Cap Nut

• H (x3) – Cable Clip

• I (x1) – Desk Clamp Assembly

• J (x5) – Cable Clip

• K (x1) – Allen Key Holder

• L (x1) – Protective Pad

• M (x1) – 4mm Allen Key

• N (x1) – 5mm Allen Key

• O (x1) – 6mm Allen Key

• M-A (x12) – M4x12 Screws

• M-B (x12) – M4x16 Screws

• M-C (x12) – M5x12 Screws

• M-D (x12) – M5x16 Screws

• M-E (x12) – D5 Washers

• M-F (x12) – Spacers

To assemble the monitor arms, connect the Left Arm (D) to the Right Arm (E) by sliding them together as shown in the diagram.

Attach the Pole (B) to the Base (C) using the provided screws and tighten them with the 4mm Allen Key (M). After securing the pole, snap the Cable Clip (H) onto the back of the pole.

The desk clamp (I) can be used as an alternative mounting option for desks between 10mm and 75mm thick. Attach the clamp assembly to the bottom of the Pole (B) and tighten it securely to the edge of your desk.

Slide the assembled monitor arms (D and E) onto the Pole (B). To adjust the height, loosen the screw on the arm collar using the 5mm Allen Key (N), move the arms to the desired height, and then tighten the screw to lock it in place.

1. Place your monitor face down on a soft surface.

2. Align the VESA Plate (A) with the mounting holes on the back of your monitor.

3. Use the D5 Washers (M-E) with either the M4x12 Screws (M-A) or M5x12 Screws (M-C), depending on your monitor’s requirements.

4. Securely fasten the VESA plate to the monitor. Do not over-tighten.

1. Place your monitor face down on a soft surface.

2. Place the Spacers (M-F) over the mounting holes on the back of your monitor.

3. Align the VESA Plate (A) over the spacers.

4. Use the D5 Washers (M-E) with either the M4x16 Screws (M-B) or M5x16 Screws (M-D), depending on your monitor’s requirements.

5. Securely fasten the VESA plate to the monitor. Do not over-tighten.

1. Once the VESA plates are attached to your monitors, hang each monitor onto the mounting points on the arms.

2. Secure each monitor by screwing on the Cap Nut (G) to the top of the mounting bolt.

3. Use the 6mm Allen Key (O) to make final height adjustments at the VESA mount if necessary.

Route your monitor cables along the arms and down the main pole using the provided Cable Clips (H and J). For convenience, the Allen Key Holder (K) attaches to the Cable Clip (H) on the main pole, providing storage for the 4mm Allen Key (M) and 6mm Allen Key (O).

• Rotation: The monitors can be rotated 360 degrees to switch between landscape and portrait orientation.

• Swivel: The outer monitor arms can be swiveled inwards and outwards for optimal positioning.

• Tilt: To adjust the monitor tilt, use the 5mm Allen Key (N) on the joint behind the VESA plate. You can tilt the monitor up to +45 degrees up or -45 degrees down. Tighten the screw to lock the tilt angle in place.