MOUNT-IT! MI-2752L (01) PDF DOCUMENT

Please follow these instructions when unpacking your MOUNT-IT! MI-2752L:

• Carefully open the carton, remove contents and lay out on cardboard or other protective surface to avoid damage.

• Check package contents against the Supplied Parts List to assure that all components were received undamaged. Do not use damaged or defective parts.

• Carefully read all instructions before attempting installation.

Please review the following safety information before installing the MOUNT-IT! MI-2752L:

• Install and operate this device with care. Please read this instruction before installation, and carefully follow all instructions contained herein. Use proper safety equipment during installation.

• Please call a qualified installation contractor for help if you don’t understand these directions or have any doubts about the safety of the installation.

• Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

• This monitor desktop mount must be securely attached to the horizontal desk. If the mount is not properly installed it may fall, resulting in possible injury and/or damage.

Follow these steps to install the pole (a) using the desk clamp:

1. Remove the 3pcs M5X20 bolts at the bottom of the pole (a) with the Allen key (o).

2. Install the “c”-Clamp Brace (c) to the Pole (a) using the 3pcs M5x20 Bolts, and tighten using the Allen Key (o).

3. Install the “c”-Clamp (b) to the pole assembly according to the thickness of the desktop. The thickness can be changed to one of three positions. Connect it using 2 pcs M8x12 Bolts (f), and tighten using the Allen Key (o).

4. Tighten the “c”-Clamp to the desktop by twisting the plastic knob.

If the existing grommet hole comes with a plastic protector, remove it to ensure a flat surface before installing the desk mount.

1. Remove the 3pcs M5X20 bolts at the bottom of the pole (a) with the Allen key (o).

2. Install the Grommet Base Plate (l) to the Pole (a) using 3 pcs M5x20 Bolts, and tighten using the Allen Key (o).

3. Position the Pole (a) on the mounting surface and secure using the Support Plate (i), M10 Washer (j), Spring Washer (k), and M10 Bolt (h). Fasten the M10 Bolt using the provided Wrench (p).

To install the pole by drilling a hole, follow these steps:

1. Remove the 3pcs M5X20 bolts at the bottom of the pole (a) with the Allen key (o).

2. Position the Pole (a) on the mounting surface and mark the center hole. Drill a 3/8″ (10mm) diameter hole at the marked position through the mounting surface.

3. Install the Grommet Base Plate to the Pole (a) using 3pcs M5x20 Bolts, and tighten using the Allen Key (o).

4. Position the Pole (a) on the mounting surface and secure using the Support Plate (i), M10 Washer (j), Spring Washer (k) and M10 Bolt (h). Fasten the M10 Bolt using the provided Wrench (p).

Place the Swivel Arm (d) over the pole (a), and tighten with the Allen Key (o).

For a Monitor with a Flat Back:

Attach the VESA Plate (e) to the back of the monitor using four M4x12 Bolts (q).

For a Monitor with a Curved or Recessed Back:

Place the M8 Spacers (s) between the VESA Plate (e) and the monitor. Secure with four M4x30 Bolts (r).

1. Before sliding the monitor on, ensure the security nut on the head of the swivel arm is turned out.

2. Slide the monitor with the attached VESA plate onto the head of the Swivel Arm (d).

3. Install the security Nut. Make sure the security nut is installed before you rotate the monitor.

To adjust the tilt angle:

Adjust and tighten the bolt with the supplied Allen Key (o) to fix the tilt angle at your desired position (+45° to -45°).

If one monitor is lower than the other:

If one monitor is lower, remove the Nut on the VESA head and turn the bolt counter-clockwise with the supplied Allen key (o) to raise the monitor. Install the Nut after the adjustment is complete.

Note: Never swivel forward or backward too much, as accidental falling might occur.

Use the provided Wire Clips (m) and (n) to hold wires in place. You can also use the provided Allen Key (o) to make the necessary adjustments to each arm.