MOUNT-IT MI-4222 (01) PDF DOCUMENT

Read the entire instruction manual before you start installation and assembly.

CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.

Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.

Safety gear and proper tools must be used. This product should only be installed by professionals.

This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.

Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.

This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.

This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.

IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, contact the manufacturer for a replacement.

MAINTENANCE: Check that the product is secure and safe to use at regular intervals (at least every three months).

CHOKING HAZARD: Package includes small parts. Not for children under 3 years. Adult supervision is required.

Compatible VESA Sizes: 75×75, 100×100, 200×100, 200×200

Compatible TVs: Up to 37″ Flat/Curved

Rated Weight Capacity: 44 lbs (20 kg)

Caution: The weight capacity is for the MOUNT ONLY. Ensure all mounting surfaces are capable of holding the weight of your TV and the Mount. DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR!

Check carefully to make sure there are no missing or defective parts. Some hardware provided may not be used. Use the correct wall mounting and TV mounting hardware suitable for your installation.

Mount and Accessories

A (x1) – Mount

B (x1) – 4mm Allen Wrench

C (x1) – 6mm Allen Wrench

TV Mounting Hardware

M-A (x4) – M4x14

M-B (x4) – M5x14

M-C (x4) – M6x14

M-D (x4) – M8x20

M-E (x4) – D5 Washer

M-F (x4) – D8 Washer

M-G (x8) – Spacer

Cabinet/Ceiling Mounting Hardware

D (x6) – ST6.3×19 Cabinet Mounting Screw

E (x6) – Cabinet Mounting Washer

W-A (x4) – Lag Screw (Ceiling Mounting)

W-B (x4) – Concrete Anchor (Ceiling Mounting)

W-C (x2) – Washer

Step 1: Removing the VESA Plate

Using the 4mm Allen Wrench (#B), remove the bolts shown in the magnification bubble to remove the VESA plate from the Mount (#A). Set the removed bolts aside; they will be used to re-connect these pieces in step 5.

Step 2: Releasing the Latch

Release the latch to unfold the mount by pressing the folded mount inward until the latch releases. Then pull the mount outward until it has been fully unfolded.

1. With a stud finder, locate the stud and hold the Mount (#A) on the stud in the desired location. Mark the center of the middle teardrop-shaped hole. You may need to rotate the mount arm to access the screw hole.

2. Use a 3/16″ drill bit and drill on the marked location to a depth of 2.2″.

3. Install 1 Lag Screw (#W-A) but do not fully tighten. Leave a gap of approximately 0.15″ (4mm).

4. Place the mount over the Screw so that it passes through the middle of the three teardrop-shaped holes, then slide the mount back so that the bolt rests in the smaller end of the hole.

5. On the other side of the bracket, through the middle of the 3 bolt holes, install the second Lag Screw (#W-A) and 1 Washer (#W-C) and tighten both bolts until secure.

Note: Do not drill mounting holes into mortar (such as between bricks or stones). Only drill and install into solid stone or concrete surfaces.

1. Hold the Mount (#A) to the desired location on the wall and mark the center of the mounting holes with a pencil. Only mark the 4 outer mounting screw locations; the middle two holes will not be used.

2. Use a 3/8″ drill bit and drill on the marked locations to a depth of 2.4″. Clear any dust and debris from the holes and insert the Concrete Anchors (#W-B).

3. Install 2 Lag Screws (#W-A) to the location corresponding with the two teardrop-shaped holes, but do not fully tighten. Leave a gap of approximately 0.15″ (4mm).

4. Place the mount over the Screws so that it passes through the teardrop-shaped holes, then slide the mount back so that the bolt rests in the smaller end of the hole.

5. Install the final two Lag Screws (#W-A) and 2 Washers (#W-C) and tighten all bolts until secure. Do not overtighten.

1. Hold the Mount (#A) on the underside of the cabinet or other solid wood surface in the desired location. Mark the center of all 6 mounting holes, ignoring the larger opening of the teardrop-shaped holes and instead marking the center of the other end. You may need to rotate the mount arm to access the screw holes.

2. Use a 3/16″ drill bit and drill on the marked locations to a depth of 0.78″.

3. Rotate the arm so that the outer 4 holes are accessible and install the mount to the pre-drilled holes using 4 Cabinet Mounting Washers (#E) and 4 Cabinet Mounting Screws (#D), and tighten until secure.

4. Rotate the arm again to access the final two holes, and install the next two Washers (#E) and Screws (#D), then tighten until secure.

Note: If mounting on particle board cabinets, please ensure the cabinet can safely support the weight of the TV and the mount.

1. Lay your TV screen side down on a flat or soft surface.

2. Select the appropriate size mounting bolt (select one size #M-A, M-B, M-C, or M-D) and washer (#M-E or M-F) for your display’s mounting holes. Verify the length of the VESA bolt is not too long. If you are unsure of the correct bolt size for your display, refer to your TV user manual.

3. If necessary, use the included spacers (#M-G) between the mount and the TV to adjust the length of the mounting bolt. Multiple spacers can be used in combination to achieve the desired bolt depth.

4. Attach the VESA Plate using the selected bolts and tighten until secure. Do not overtighten.

1. Hang the top portion of the VESA plate back on the arm as shown in the manual’s diagram.

2. Reinstall the bolts removed in Step 1 to their original location, securing the VESA plate back to the Mount Arm. Tighten until secure using the 4mm Hex Wrench (#B).

Height Adjustment

To adjust the height of the screen, use the 4mm Hex Wrench (#B) to loosen the bolt indicated in the magnification bubble on the left of the diagram. Once loosened, the screen and VESA plate will be able to be moved up or down on the arm. Tighten the bolt back in place to fix the screen at the desired height.

Folding Movement Adjustment

To adjust the folding movement of the arm to be lighter, heavier, or fixed, remove the decorative covers. Use the 6mm Hex Wrench (#C) to adjust the tension of the screw. Test if the movement is satisfactory by folding or moving the arm joint. Replace the decorative covers when finished.

The mount can be folded up for storage and lowered for viewing to a maximum angle of 90°.

The mount may be swiveled up to +/- 50° left or right.