MOTOROLA MBP55-2 (01) PDF Document

1. Display (LCD screen)

2. VIDEO ON/OFF button: Press to turn the LCD screen ON/OFF.

3. TALK button: Press and hold to speak to your baby.

4. RESET button (recessed): Use a small pin to press.

5. UP button: In Normal Mode, it tilts the camera up. In Menu Mode, it moves up through menu options.

6. DOWN button: In Normal Mode, it tilts the camera down. In Menu Mode, it moves down through menu options.

7. MENU button: Press to open or close the Menu options.

8. OK button: Confirms a selection.

9. Micro USB power adapter socket

10. LEFT button: In Normal Mode, it pans the camera left. In Menu Mode, it moves left along menu options.

11. RIGHT button: In Normal Mode, it pans the camera right. In Menu Mode, it moves right along menu options.

12. Charging LED: Blue when mains power is connected.

13. Parent Unit ON/OFF LED: Green when the unit is on.

14. Audio Level LEDs: Green, Amber, Red, Red lights that indicate the sound level.

15. Volume buttons: Press -/+ to decrease/increase the volume level.

16. Power button: Press and hold to turn the Parent Unit ON/OFF.

17. Microphone

18. Stand

19. Speaker

1. Photo Sensor (Night Vision Mode)

2. Camera Lens

3. Infrared LEDs (x 8, for night vision)

4. Power LED: On when linked to Parent Unit. Flashes when searching for Parent Unit.

5. Microphone

6. Camera Battery LED: On when AC power is connected to the camera. Flashes when the battery level of the camera is low.

7. POWER ON/OFF switch

8. Temperature Sensor

9. Power Adapter Outlet

10. PAIR button

11. Speaker

12. Star Grip or Tripod mount screw hole

To use your Video Monitor Baby and Parent Units together, you must be able to establish a radio link between them, and the range will be affected by environmental conditions.

• Any large metal object, like a refrigerator, a mirror, a filing cabinet, metallic doors or reinforced concrete between the Baby and Parent Unit may block the radio signal.

• The signal strength may also be reduced by other solid structures, like walls, or by radio or electrical equipment, such as TVs, computers, cordless or mobile phones, fluorescent lights or dimmer switches.

• Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers), Bluetooth™ systems, or microwave ovens, may cause interference with this product, so keep the Baby Monitor away at least 1 metre (or 1.5m / 5ft) from these types of products, or turn them off if they appear to be causing interference.

• If the signal is weak, try moving the Parent and/or the Baby Unit to different positions in the room(s).

• Your Baby and Parent Units may be too close. Move them farther apart. Make sure there is at least 1 to 2 metres between the 2 units to avoid audio feedback.

Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 1m (3ft) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.

Baby Unit Set Up & Use:

• Choose a location for the Baby Unit that will provide the best view of your baby in their cot.

• Place the Baby Unit on a flat surface, such as a dresser, desk, or shelf or mount the Unit to a wall securely using the keyhole slots on the underside of the stand.

• NEVER place the Baby Unit or cords in the cot or within reach of the baby (the unit and cords should be more than 1 metre away).

General Warnings:

• This product is not a toy. Do not allow children to play with it.

• This Baby Monitor is not a substitute for responsible adult supervision.

• Keep the cords out of reach of children.

• Do not cover the Baby Monitor with a towel or blanket.

• Do not use the Baby Monitor near water or a heat source.

• Only use the chargers and power adapters provided. Do not use other chargers or power adapters as this may damage the device and battery pack.

• Do not touch the plug contacts with sharp or metal objects.

CAUTION: The Parent Unit includes a built-in, lithium-ion rechargeable battery pack, which is not a user-accessible item. If you think the battery needs replacing, please contact the helpline. Do not try to replace it yourself. Risk of explosion if battery is replaced by an unapproved battery type. Dispose of used batteries according to their instructions.

1. Connect the small plug of the power adapter to the Baby Unit (camera) and the other end to a suitable mains power socket. Only use the enclosed power adapter (5V DC / 1000mA).

2. Slide the POWER ON/OFF switch to the ON position. The power LED will light up in Green.

3. Slide the POWER ON/OFF switch to the OFF position to turn the Baby Unit off.

IMPORTANT: The Baby Unit can operate without a power connection for up to 3 hours with its built-in rechargeable battery (Ni-MH battery 2.4V, 900mAh). Please charge the unit for at least 16 hours for the first time use.

The Parent Unit has a built-in rechargeable battery pack (Lithium-ion battery 1880mAh), which gives up to 5 hours of monitor operation. Please charge it for 16 hours before initial use.

1. Connect the micro USB plug of the power adapter to the Parent Unit and the other end to a suitable mains power socket. Only use the enclosed power adapter (5V DC / 1000mA).

2. Press and hold the POWER ON/OFF button for 3 seconds to turn ON the Parent Unit.

3. To turn OFF the Parent Unit, press and hold the POWER ON/OFF button until the progress bar finishes scrolling.

NOTE: The battery icon turns RED to indicate that the battery is low, and the parent unit will beep every 15 seconds. The battery needs to be recharged; it will take 16 hours to charge fully.

When charging:

• If the Parent Unit is turned OFF with the adapter plugged in, a 2-pin plug logo will appear on-screen for about 5 seconds, and then a flashing battery logo will display for 15 seconds. The Blue LED at the top left will light up, indicating that the adapter is plugged in and charging is continuing.

• Whilst the power is ON and the adapter is plugged in, the battery icon at the top right corner of the screen will show that the battery is charging. The Charging LED at the top left will also light up.

The Baby Monitor is pre-registered. You do not need to register it again unless the Baby Unit loses its link. To re-register or register a new Baby Unit, follow these steps:

1. Press the MENU button on the Parent Unit.

2. Press the LEFT or RIGHT button until the Camera Control icon is highlighted, and the scan menu (delete, add, view, scan) will pop up.

3. Press the UP or DOWN button to select ‘add’, and press the OK button to confirm.

4. The camera list (*1/2/3/4) will pop up. Press the UP or DOWN button to select the desired Camera and press the OK button to start searching for a camera unit. “press PAIR on cam” will be shown.

Note: If a camera is currently paired, its location (with a * against it) cannot be selected for a new registration.

5. Press and hold the PAIR button underneath the Baby Unit until the Parent Unit finds the camera, beeps and ‘PAIR OK’ appears on the screen. The video from the camera will then appear.

NOTE: If a particular Baby Unit was registered previously, registering this current Baby Unit again will cancel its old registration.

Setting up:

• Place the Baby Unit in a convenient location (e.g., on a table) and point the camera lens towards the area you want to monitor.

• Adjust the angle of the Baby Unit’s camera by using the pan and tilt function from the Parent Unit (up, down, left, right) until you are satisfied with the image.

Pan and Tilt:

• Press the UP or DOWN button to tilt up or down.

• Press the LEFT or RIGHT button to pan left or right.

Night Vision Mode:

The Baby Unit has 8 high-intensity infrared LEDs for clear images in the dark. When the photo sensor detects a low level of ambient light, the LEDs activate automatically, and the Parent Unit screen will display in black and white. The night vision icon will be displayed at the top of the screen.

Talk Mode:

Press and hold the TALK button on the Parent Unit to talk to your baby through the Baby Unit’s loudspeaker. The talk icon will be displayed at the top of the LCD screen.

Video ON/OFF:

Press the VIDEO ON/OFF button to turn the LCD screen on or off, whilst still leaving the audio monitor on.

The temperature reading from the sensor at the back of the Baby Unit is displayed at the top of the LCD screen in °C or °F.

• The readings will turn RED if the temperature goes above 29°C / 84°F or below 14°C / 57°F.

• The reading will change to HH °C / °F if the temperature goes above 36°C / 97°F.

• The reading will change to LL °C / °F if the temperature goes below 1°C / 34°F.

Volume:

Press the Volume button – or + to adjust the volume level from 0-8. Level 0 is OFF.

Brightness:

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Brightness icon is highlighted.

3. Press the UP or DOWN button to select the desired brightness level from 1-8.

Lullaby Sounds:

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Lullaby icon is highlighted.

3. Press the UP or DOWN button to select from the 5 sounds. A selected sound will repeat continually until unselected or the TALK button is pressed.

Zoom:

1. Press the MENU button until the Zoom icon is highlighted.

2. Press the UP or DOWN button to select 1X or 2X Zoom.

Alarm:

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Alarm icon is highlighted.

3. Press the UP or DOWN button to select the alarm time (6h, 4h, 2h) or OFF. The alarm icon will turn on.

4. If an alarm is set, the Parent Unit will beep for about 1 minute after the period, and the icon will flash. Press any button to stop the alarm.

Temperature Unit:

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Temperature icon is highlighted.

3. Press the UP or DOWN button to select °C or °F.

View a camera:

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Camera Control icon is highlighted.

3. Press the UP or DOWN button to select ‘view’, and press OK.

4. Select the desired camera (*1/2/3/4) and press OK. Only locations with a * can be selected.

TIP: For a quick method, directly press the OK button repeatedly to cycle through available camera options.

Delete a camera:

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Camera Control icon is highlighted.

3. Press the UP or DOWN button to select ‘delete’, and press OK.

4. Select the desired camera and press OK.

5. Press the UP or DOWN button to select the checkmark, then press OK to delete the registration.

Note: You cannot delete the camera if there is only one registered camera in the system.

Scan camera:

This is only available with more than one Baby Unit.

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Camera Control icon is highlighted.

3. Press the UP or DOWN button to select ‘scan’, and press OK.

4. The screen will display images from different registered cameras in a loop, changing about every 12 seconds.

Power Saving mode:

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Power Saving icon is highlighted.

3. Press the UP or DOWN button to select auto video off after 5 mins, 30 mins, or 60 mins if operating on batteries only.

Note: The audio will stay on, and you can press any key to switch the video back on.

View multiple cameras on screen:

This is only available with more than one Baby Unit.

1. Press the MENU button.

2. Press the LEFT or RIGHT button until the Split Screen icon is highlighted.

3. Press the UP or DOWN button to select Split Screen On or Off.

4. When Split Screen is On, press the directional buttons (LEFT/RIGHT/UP/DOWN) to switch between cameras to hear the audio from the selected camera, indicated by a red frame.

Note: In multi-screen mode, the TALK button operates with the selected camera. If you want to play a lullaby, you must set it before selecting multi-screen mode. Zoom does not work in multi-screen mode.

Clean the Baby Monitor with a slightly damp cloth or with an anti-static cloth. Never use cleaning agents or abrasive solvents.

Cleaning and care:

• Do not clean any part of the product with thinners or other solvents and chemicals – this may cause permanent damage to the product which is not covered by the warranty.

• Keep the Baby Monitor away from hot, humid areas or strong sunlight, and don’t let it get wet.

At the end of the product lifecycle, you should not dispose of this product with normal household waste. Take this product to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s guide and/or box indicates this.

The internal battery should be disposed of with the Parent unit in an environmentally-friendly manner according to your local regulations.

• Try recharging or press the RESET button once.

• Reset the units. Press the RESET button once on the Parent Unit and unplug both the units’ electrical power, then plug them back in.

• Is the unit turned on (green ON/OFF LED lit)? Press and hold the ON/OFF button on the Parent Unit to turn it ON.

• Is the correct camera selected? Change the camera number, if necessary.

• Is the video display turned on? Press the VIDEO ON/OFF button to turn it on.

• When operating using batteries only, the Display will go blank after 5, 30, or 60 minutes to save power (depending on settings). The unit is still active and will give you audio alerts. You can reactivate the screen by pressing any button.

• Try recharging or press the RESET button once on the Parent Unit.

• If the Baby Unit is too far away it may be going out of range, so move the Baby Unit closer to the Parent Unit.

• Reset the units by disconnecting the Baby Unit from electrical power and press the RESET button once on the Parent Unit. Wait about 15 seconds before reconnecting. Allow up to one minute for the Baby Unit and the Parent Unit to synchronise.

• See the instructions for Registration (Pairing) if there is a need to re-register the units.

• Your Baby and Parent Units may be too close. Move them farther apart.

• Make sure there is at least 1 to 2 metres between the 2 units to avoid audio feedback.

• If the baby unit is too far away it may be out of range, so move the Baby Unit closer to the Parent Unit.

• Make sure the Baby and Parent Units are not near other electrical equipment, such as a television, computer or cordless/mobile telephone.

• Use of other 2.4 GHz products, such as wireless networks (Wi-Fi® routers), Bluetooth™ systems, or microwave ovens, may cause interference with this product, so keep the baby monitor away at least 1.5m (5ft) from these types of products, or turn them off if they appear to be causing interference.

• If the signal is weak, try moving the Parent and/or Baby Unit to different positions in the rooms.

Baby Unit

Parent Unit