MOTOROLA L702CBT (01) PDF Document

When using your MOTOROLA L702CBT, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool).

5. Do not place this product on an unstable cart, stand, or table.

6. Slots and openings in the back or bottom of the base unit and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.

9. Never push objects of any kind into this product through the slots in the base or handset, as they may touch dangerous voltage points or short-out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product. Take it to a qualified service-person when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks.

11. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled onto the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating instructions.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance.

12. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

13. Do not use the telephone to report a gas leak in the vicinity of the leak.

14. Use only the supplied Ni-MH battery pack. The operational time for the handset may vary depending on the battery’s charge level. The battery must be recycled or disposed of properly.

The following items are included with your MOTOROLA L702CBT:

• Telephone Base

• Cordless Handset

• Corded Handset

• AC Power Adapter

• Telephone Line Cord

• Handset Cord

• Cordless Handset Battery Pack

• Corded Handset Battery Pack (pre-installed)

• User’s Guide

The controls on the telephone base of the MOTOROLA L702CBT are as follows:

1. **IN USE indicator:** On when the phone is in use, the answering system is answering a call, or during handset deregistration. Flashes when there is an incoming call, during handset/cell phone registration, or when the line is on hold.

2. **CELL 1 indicator:** On when cell phone 1 is connected via Bluetooth.

3. **CELL 2 indicator:** On when cell phone 2 is connected via Bluetooth.

4. **DELETE:** Press to delete the message currently playing.

5. **ANSWER ON/OFF:** Press to turn the answering system on or off.

6. **Message counter:** Displays the number of messages.

7. **SKIP:** Press to skip to the next message.

8. **PLAY/STOP:** Press to play messages; press again to stop.

9. **REPEAT:** Press to repeat the current message from the beginning. Press twice to play the previous message.

10. **FIND HS:** Press to page the cordless handset.

11. **VOLUME + / -:** Adjusts the speaker volume on the base.

12. **CELL 1:** Press to connect or disconnect cell phone 1.

13. **CELL 2:** Press to connect or disconnect cell phone 2.

14. **SPEAKER:** Press to use the speakerphone.

The controls on the corded handset of the MOTOROLA L702CBT are as follows:

1. **MENU/OK:** Press to enter the main menu, confirm a selection, or save a setting.

2. **CALLS/UP:** Press to view the Caller ID list. In menu mode, press to scroll up.

3. **REDIAL/DOWN:** Press to view the redial list. In menu mode, press to scroll down.

4. **TALK/FLASH:** Press to make or answer a call. During a call, press for Call Waiting.

5. **PHONEBOOK/LEFT:** Press to access the phonebook.

6. **DELETE/MUTE/RIGHT:** In idle mode, press to access the Intercom menu. During a call, press to mute the microphone. In editing mode, press to delete a character/digit.

7. **1:** During a call, press and hold to insert a pause.

8. **TONE:** Press to switch to Tone dialing temporarily during a call.

9. **OFF/EXIT:** During a call, press to end the call. In menu mode, press to return to the previous menu or idle screen.

10. **SPEAKER:** Press to make or answer a call using the speakerphone.

11. **VOLUME:** During a call, press to adjust the listening volume.

The controls on the cordless handset of the MOTOROLA L702CBT are as follows:

1. **Handset Earpiece**

2. **LCD Display**

3. **MENU/OK:** Press to enter the main menu, confirm a selection, or save a setting.

4. **CALLS/UP:** Press to view the Caller ID list. In menu mode, press to scroll up.

5. **REDIAL/DOWN:** Press to view the redial list. In menu mode, press to scroll down.

6. **TALK/FLASH:** Press to make or answer a call. During a call, press for Call Waiting.

7. **PHONEBOOK/LEFT:** Press to access the phonebook.

8. **DELETE/MUTE/RIGHT:** In idle mode, press to access the Intercom menu. During a call, press to mute the microphone. In editing mode, press to delete a character/digit.

9. **1:** During a call, press and hold to insert a pause.

10. **TONE:** Press to switch to Tone dialing temporarily during a call.

11. **OFF/EXIT:** During a call, press to end the call. In menu mode, press to return to the previous menu or idle screen.

12. **SPEAKER:** Press to make or answer a call using the speakerphone.

13. **VOLUME:** During a call, press to adjust the listening volume.

14. **Handset Microphone**

15. **Charging Contacts**

To install and connect your MOTOROLA L702CBT, follow these steps:

1. **Install the Telephone Base:** Plug one end of the telephone line cord into the TEL LINE jack at the back of the telephone base and the other end into the telephone wall jack.

2. **Connect the AC Adapter:** Plug the AC adapter into the DC 9V jack at the back of the telephone base and the other end into a wall outlet.

3. **Connect the Corded Handset:** Plug one end of the coiled handset cord into the handset cord jack on the left side of the telephone base and the other end into the jack at the bottom of the corded handset.

4. **Install the Cordless Handset Battery:**

a. Slide open the battery compartment cover.

b. Plug the battery pack connector securely into the socket inside the compartment.

c. Place the battery pack inside the compartment.

d. Slide the battery compartment cover back on.

5. **Charge the Cordless Handset:** Place the cordless handset on the telephone base to charge. For initial use, charge the handset for at least 14 hours. A beep sounds when the handset is properly placed on the base or charger.

To pair a cell phone with your MOTOROLA L702CBT, follow these steps:

1. Press MENU/OK on the corded or cordless handset.

2. Use the UP/DOWN keys to select BLUETOOTH, then press MENU/OK.

3. Select PAIR CELL PHONE, then press MENU/OK.

4. Select either CELL 1 or CELL 2 and press MENU/OK. The handset will display “Pairing… Please turn on Bluetooth on your cell”.

5. Turn on the Bluetooth feature on your cell phone and search for new devices. Your cell phone should find “MOTOROLA L702CBT”.

6. Select “MOTOROLA L702CBT” on your cell phone to connect.

7. If your cell phone prompts for a PIN, enter “0000”.

8. Once paired successfully, the corresponding CELL 1 or CELL 2 icon will appear on the handset display, and the CELL 1 or CELL 2 indicator on the base will light up.

Before downloading, ensure your cell phone is paired and connected to your MOTOROLA L702CBT. Follow these steps:

1. Press MENU/OK on the corded or cordless handset.

2. Use the UP/DOWN keys to select BLUETOOTH, then press MENU/OK.

3. Select DOWNLOAD PB, then press MENU/OK.

4. Select which cell phone’s phonebook to download (e.g., FROM CELL 1) and press MENU/OK.

5. The screen will display “Deleting old phonebook records.” followed by “Downloading…”.

6. During the download, you may need to respond to a prompt on your cell phone to allow the phonebook transfer.

7. Once completed, the screen displays “Download complete”. The cell phone phonebook entries are stored in the CELL phonebook on your MOTOROLA L702CBT.

You can make a call on your MOTOROLA L702CBT in several ways:

Using the Corded Handset:

1. Pick up the corded handset.

2. Dial the phone number.

Using the Cordless Handset:

1. Press the TALK/FLASH key.

2. Dial the phone number.

Using the Speakerphone (Base or Handset):

1. Press the SPEAKER key.

2. Dial the phone number.

To make a cell call through a connected Bluetooth device:

1. Press the desired CELL 1 or CELL 2 button on the base.

2. When you hear a dial tone, dial the number using the keypad.

Predialing:

1. Enter the phone number while the phone is in idle mode.

2. Press TALK/FLASH or SPEAKER on the handset, or pick up the corded handset to dial the number.

To answer a call on your MOTOROLA L702CBT:

• On the Corded Handset: Pick up the handset from the base.

• On the Cordless Handset: Press the TALK/FLASH or SPEAKER key.

• On the Base Speakerphone: Press the SPEAKER key.

To end a call on your MOTOROLA L702CBT:

• On the Corded Handset: Place the handset back on the base.

• On the Cordless Handset: Press the OFF/EXIT key or place the handset back on the base or charging cradle.

• On the Base or Handset Speakerphone: Press the SPEAKER key.

The MOTOROLA L702CBT stores the last 5 numbers dialed. To use the redial list:

1. Press the REDIAL/DOWN key on the corded or cordless handset when it is idle.

2. Use the UP/DOWN keys to scroll through the redial list.

3. To dial a number from the list, pick up the corded handset, or press TALK/FLASH or SPEAKER on either handset.

To adjust the volume on your MOTOROLA L702CBT:

• **During a call:** Press the VOL + or VOL – keys on the side of the active handset (corded or cordless) or on the base if using the base speakerphone to adjust the listening volume.

• **Ringer Volume:** You can adjust the ringer volume for the base and each handset through the menu settings when the phone is not in use. Navigate to Menu > Ring Setup > Ringer Volume.

To locate a misplaced cordless handset for your MOTOROLA L702CBT, press the FIND HS button on the telephone base. All registered cordless handsets will ring for 60 seconds. You can stop the ringing by pressing the FIND HS button again, or by pressing any key on the cordless handset.

To store a contact in the phonebook of your MOTOROLA L702CBT:

1. Press MENU/OK on the handset.

2. Select PHONEBOOK and press MENU/OK.

3. Select ADD NEW ENTRY and press MENU/OK.

4. Enter the name (up to 16 characters) using the keypad. Press the key multiple times for different characters.

5. Press MENU/OK to save the name.

6. Enter the phone number (up to 24 digits).

7. Press MENU/OK to save the number.

To review and dial a number from the Caller ID list on your MOTOROLA L702CBT:

1. Press the CALLS/UP key on the corded or cordless handset when it is idle.

2. Use the UP/DOWN keys to scroll through the list of calls.

3. To dial a displayed number, pick up the corded handset, or press TALK/FLASH or SPEAKER on either handset.

You can operate the answering system on your MOTOROLA L702CBT using the keys on the telephone base or through the handset menu.

Turning On/Off:

• Press the ANSWER ON/OFF button on the base. When on, it will announce “Answering machine is on.” When off, it will announce “Answering machine is off.”

Playing Messages:

• Press the PLAY/STOP button on the base. The system will announce the number of new messages and play them.

Deleting Messages:

• While a message is playing, press the DELETE button on the base to delete that specific message.

Recording a Personal Greeting (OGM):

1. Press MENU/OK on the handset.

2. Select ANSW. MACHINE, then press MENU/OK.

3. Select OGM SETTING, then press MENU/OK.

4. Select ANSWER & REC or ANSWER ONLY, then press MENU/OK.

5. Select RECORD OGM and follow the voice prompts to record your greeting. Press MENU/OK to stop and save.

To set the date and time on your MOTOROLA L702CBT:

1. Press MENU/OK on the handset.

2. Use the UP/DOWN keys to select SETTINGS, then press MENU/OK.

3. Select DATE & TIME and press MENU/OK.

4. Enter the current month, day, and year using the number keys (e.g., 08-15-17 for August 15, 2017).

5. Press MENU/OK.

6. Enter the current time in 12-hour format using the number keys (e.g., 07-35 for 7:35).

7. Use the UP/DOWN keys to select AM or PM.

8. Press MENU/OK to save the settings.

The display icons on your MOTOROLA L702CBT indicate the phone’s status. Here is a list of common icons and their meanings:

If there is no dial tone on your MOTOROLA L702CBT, please check the following:

• Make sure the telephone line cord is securely plugged into the base unit’s TEL LINE jack and the telephone wall jack.

• Ensure the AC power adapter is plugged into the base unit and a working electrical outlet.

• Check that the cordless handset battery is charged. If it is low, charge it for 14 hours.

• Disconnect the base from the wall jack and connect another working phone. If the other phone works, the issue may be with your MOTOROLA L702CBT. If the other phone does not work, the problem may be with your telephone line.

• If you are trying to use a cell line, ensure your cell phone is paired and connected to the base via Bluetooth.

If you are unable to pair your cell phone with the MOTOROLA L702CBT, try these solutions:

• Make sure the Bluetooth feature is turned on for your cell phone.

• Ensure the telephone base of the MOTOROLA L702CBT is in pairing mode (the handset should display “Pairing…”).

• Keep your cell phone close to the telephone base during the pairing process.

• Turn both the telephone base and your cell phone off and then on again, and repeat the pairing procedure.

• If the base already has two cell phones paired, you must first delete one of the paired devices before adding a new one.

If Caller ID is not working on your MOTOROLA L702CBT, please check the following:

• You must be subscribed to a Caller ID service from your telephone service provider for this feature to work.

• Both you and the caller must be in areas that offer Caller ID service.

• The caller’s information may not be displayed if they are calling from an area that does not support sending Caller ID information, or if they have blocked their number.

If the cordless handset of your MOTOROLA L702CBT does not ring, please check the following possibilities:

• The ringer may be turned off. Check the ringer volume settings in the menu.

• Ensure the telephone line cord is securely connected to the base and the wall jack.

• The cordless handset may be out of range of the base. Move closer to the base unit.

• The battery pack in the cordless handset may be low. Place the handset on the base to recharge.

If you are experiencing noise or interference on your MOTOROLA L702CBT, consider the following causes and solutions:

• The handset may be out of range. Move closer to the telephone base.

• The telephone base may be located near appliances such as televisions, microwaves, computers, or other cordless phones. Move the base to a different location away from such devices.

• The building materials of your home (such as thick walls) can sometimes shorten the range. Try relocating the base.