MIDEA MLTG70N1AWW (01) PDF Document

If you smell gas while using the MIDEA MLTG70N1AWW, follow these safety steps immediately:

1. Do not try to light any appliance.

2. Do not touch any electrical switch and do not use any phone in your building.

3. Clear the room, building, or area of all occupants.

4. Immediately call your gas supplier from a neighbor’s phone and follow their instructions.

5. If you cannot reach your gas supplier, call the fire department.

When selecting a location for the MIDEA MLTG70N1AWW, ensure the following conditions are met:

1. There must be enough space at the front for loading the dryer and enough space behind for the exhaust system.

2. The room must have enough fresh air and no air-flow obstructions.

3. The ambient temperature must not be lower than 33 degrees Fahrenheit.

4. For gas models, adequate clearance must be maintained as noted on the data plate to ensure proper air for combustion.

5. The dryer must not be installed or stored where it will be exposed to water or weather.

6. The area must be kept clear of combustible materials, gasoline, and other flammable vapors and liquids.

7. The MIDEA MLTG70N1AWW is not suitable for installation in a mobile home.

The MIDEA MLTG70N1AWW requires specific minimum clearances from adjacent walls and surfaces when installed in a recessed area or closet:

Sides: 1 inch (25 mm)

Rear: 5 inches (127 mm)

Top: 24 inches (610 mm)

Closet front: 2 inches (51 mm)

Note: The front of a closet must have two unobstructed air openings for a combined minimum total area of 72 sq. in. (465 sq. cm) with a minimum clearance of 3 inches (76 mm) at the top and bottom. A slatted door with equivalent space clearance is acceptable.

For the MIDEA MLTG70N1AWW, use only 4-inch (10.2 cm) diameter rigid aluminum or rigid galvanized steel duct. Do not use flexible plastic or thin foil wall ducting. The maximum duct length depends on the number of 90 degree elbows used:

0 elbows: 90 feet (27.4 m)

1 elbow: 60 feet (18.3 m)

2 elbows: 45 feet (13.7 m)

3 elbows: 35 feet (10.7 m)

The hood should have at least 12 inches (30.5 cm) of clearance between the bottom of the hood and the ground or other obstructions. Joints should be secured with aluminum tape; do not use screws as they can catch lint.

To properly install the MIDEA MLTG70N1AWW, you will need the following tools:

1. Phillips screwdriver

2. Flat screwdriver

3. Level

4. Pliers

5. Adjustable wrench that opens to 1 inch (25 mm)

6. Aluminum tape

7. Cutting knife

8. Pipe wrench (for gas models only)

To ensure optimal performance and minimize vibration, the MIDEA MLTG70N1AWW must be leveled on a solid surface:

1. Place a level on the top of the dryer.

2. Adjust the four leveling feet at the corners of the base.

3. Extend the leveling feet only as much as necessary. Over-extending them can cause the unit to vibrate.

4. Ensure the dryer is sitting firmly on the floor and does not rock.

Follow these steps to operate the MIDEA MLTG70N1AWW:

1. Clean the lint filter before or after every load to shorten drying time and increase energy efficiency.

2. Press the POWER button to turn the dryer on.

3. Load your laundry. Place only one wash load in the dryer at a time. Avoid overloading to prevent uneven drying and excessive wrinkling.

4. Select the appropriate cycle using the Cycle Selector. Sensor Dry cycles include Normal, Bulky, Heavy Duty, Towels, Sanitize, Perm Press, and Delicates. Manual Dry cycles include Quick Dry, Time Dry, and Air Fluff.

5. Select appropriate options such as Temperature, Dryness level, and Wrinkle Care if desired.

6. Press the START/PAUSE button to begin the cycle.

The MIDEA MLTG70N1AWW control panel features several functions:

TEMP: Selects drying temperature (High for sturdy cottons, Medium for permanent press/synthetics, Low for delicate synthetics, or No Heat for air cycle).

DRYNESS: Selects the dryness level. Different levels result in different drying times.

TIME: A quick selection for manual time settings.

WRINKLE CARE: Provides approximately 90 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling.

DAMP DRY SIGNAL: Beeps 6 times when clothes are damp enough for ironing, allowing you to remove specific items before the cycle finishes.

TIME ADJUST: Adjusts the drying time for Manual cycles.

CHILD LOCK: Press and hold Dryness and Temp simultaneously for 3 seconds to lock or unlock all buttons except Power.

SIGNAL: Press and hold Time Adjust to turn the buzzer sound on or off.

The following table outlines suggested cycles for the MIDEA MLTG70N1AWW:

To maintain the MIDEA MLTG70N1AWW, follow these guidelines:

Control Panel: Clean with a soft, damp cloth. Do not use abrasive substances or spray cleaners directly on the panel.

Drum: Clean the stainless steel or anodized drum with a damp cloth and a mild, non-abrasive cleaner suitable for those surfaces. Remove residue and dry with a clean cloth.

Exterior: Clean with a soft, damp cloth. Protect the surface from sharp objects and do not place heavy items on top of the dryer.

Exhaust System: Should be inspected and cleaned yearly. Disconnect the exhaust duct from the dryer and the outside hood to remove any lint accumulation.

Lint Filter: Clean before or after every load. Do not operate the dryer without the lint filter in place.

If you encounter issues with the MIDEA MLTG70N1AWW, check these solutions:

Unit Doesn’t Start:

1. Make sure the door is latched shut.

2. Ensure the power cord is plugged into a live electrical outlet.

3. Check the home’s circuit breaker and fuses.

4. Press the Start/Pause button again if the door was opened during the cycle.

Unit Doesn’t Heat:

1. Check the home’s circuit breaker and fuses.

2. Select a heat setting other than Air Fluff and ensure the Temp selection is not on “No Heat”.

3. On a gas dryer, check that the gas supply is turned on.

4. Clean the lint filter and exhaust duct.

5. The dryer may have moved into the cool-down process of the cycle.

The MIDEA MLTG70N1AWW may display the following error codes if a malfunction occurs:

C9: The PCB failed. Stop using the dryer and call for service.

E4: The humidity sensor failed. The unit will complete the current cycle, but garments could be over-dried. The unit can still operate under Time Cycles; call for service.

E5: The temperature sensor failed. Stop using the dryer and call for service.

Note: When an error happens, the buzzer will beep for 10 seconds and repeat once every 15 minutes.

To reverse the door swing on the MIDEA MLTG70N1AWW, follow these steps:

1. Unplug the power cord.

2. Support the door and remove the four hinge screws from the door. Lift and set the door aside.

3. Remove the screws for the latch cover on the right side and the locker cover on the left side. Swap their positions and reinstall them.

4. Remove the 12 screws around the door to separate the inside door panel from the outside door board.

5. Rotate the outside door panel 180 degrees, then reassemble it with the inside door board using the 12 screws.

6. Install the hinges onto the left side of the dryer.

7. Align the hinges with the holes on the front of the dryer and secure with the four hinge screws.

For best results with the MIDEA MLTG70N1AWW, follow these load size guidelines:

Small Load: Fill the dryer drum with 3 to 4 items, not more than 1/4 full.

Medium Load: Fill the dryer drum up to about 1/2 full.

Large Load: Fill the dryer drum up to about 3/4 full. Do not overload; items need to tumble freely.

Use the following guide for specific items in the MIDEA MLTG70N1AWW:

Bedspreads & Comforters: Use Heavy Duty cycle. May require repositioning to ensure even drying.

Blankets: Use Normal cycle and dry only one blanket at a time.

Curtains & Draperies: Use Casual cycle, medium temperature, and “less dry” setting to minimize wrinkling. Dry in small loads.

Cloth Diapers: Use Normal cycle on High temperature.

Down Filled Items: Use Normal cycle on High temperature. Add dry towels to shorten drying time.

Foam Rubber: DO NOT dry on a heat setting. Use the Air Fluff cycle (no heat). Using heat may create a fire hazard.

Pillows: Use Normal cycle. Add dry towels or dryer balls to help tumbling action. Kapok or foam pillows must use Air Fluff cycle.

Plastics: Use Air Fluff or Time Dry cycle on Low or Ultra Low temperature.

Note: Do not dry fiberglass items, woolens (unless recommended), or items soaked in vegetable/cooking oils.