MIDEA MLTW44A1AWW (01) PDF Document

The MIDEA MLTW44A1AWW Top-Load Washer requires a power supply of 120V~ with a frequency of 60Hz. For the electrical requirements, use a 120 Volt, 60Hz, 15 amp fuse or circuit breaker, and an individual branch circuit is recommended for the washer only.

The capacity for the MIDEA MLTW44A1AWW Top-Load Washer is 4.4 cu ft-Agitator Capacity and 4.5 cu ft-Impeller Capacity.

The package contents for the MIDEA MLTW44A1AWW Top-Load Washer include:

• Drain Hose Guide
• Manual
• Tie (x1)
• Filter (x2)

Note: Use the filters to replace the rubber washers in the water hoses (faucet sides).

The main components of the MIDEA MLTW44A1AWW Top-Load Washer are:

• Drain hose and holder
• Control panel
• Top lid
• Cabinet
• Adjustable leg (Four legs)
• Faucet and water inlet hose (Not supplied)
• Power cord
• Water inlet valve
• See through window
• Softener compartment
• Bleach compartment
• Powder Detergent compartment
• Door Lock

To fill the MIDEA MLTW44A1AWW Top-Load Washer in the correct amount of time, the water pressure needs to be between 14 and 116 psi (100 to 800 kPa). Water inlet hoses must be purchased separately, up to 8 ft. (240 cm) in length.

To avoid the possibility of water damage, make sure that the water faucets are easily accessible, turn off the faucets when you are not using your washer, and periodically check to make sure that water is not leaking from the water hose fittings.

The recommended height for the drain standpipe for the MIDEA MLTW44A1AWW Top-Load Washer is 48 in. (122 cm). The drain hose must be routed through the drain hose clip to the standpipe, and the standpipe must be large enough to accept the outside diameter of the drain hose.

The minimum clearances between the MIDEA MLTW44A1AWW Top-Load Washer and adjacent walls or other surfaces are:

• Either side: 1 in. (2.5 cm)
• Rear: 6 in. (15.2 cm)
• Closet Front: 2 in. (5.1 cm)
• Top: 24 in. (61 cm)
• Gap between the end of water valve and the wall: 6 in. (15.2 cm)

If you install the washer and dryer side-by-side in a closet, the closet front must have an unobstructed air opening of at least 72 square inches (465 square cm).

The tools you will need for installing the MIDEA MLTW44A1AWW Top-Load Washer are:

• Pliers
• Level
• Adjustable wrench that opens to 1″ (25 mm)

To connect the water supply hoses to the MIDEA MLTW44A1AWW Top-Load Washer, follow these steps:

1. Make sure that there are rubber washers inside the fittings at both ends of each new water hose. Remove the rubber washers in faucet side and replace with filters. Installing the water supply hoses without rubber washers can cause water leakage.

2. Tighten the hose and faucet fittings by hand until they are snug, then tighten them an additional two-thirds of a turn with pliers or a wrench. Pull the water supply hoses downwards to make sure that they are connected securely.

3. Place the unconnected ends of the hoses into a bucket and turn on the faucets connected to the water supply hoses for 10 or 15 seconds to remove any foreign substances. Turn off the faucets.

4. Connect the ends of the water supply hoses to the water supply intake connections at the top of the washer. Make sure that the rubber washers are in place. The water supply hose connected to the hot faucet must be connected to the hot water supply intake and the water hose connected to the cold faucet must be connected to the cold water supply intake.

5. Tighten the fittings by hand until they are snug, and then tighten them an additional two-thirds of a turn with a pliers.

6. Turn on the hot and cold water supplies and check all the water supply intake connections and the faucets for water leaks.

Caution: Do not overtighten the fittings or apply tape or sealant to the faucets or water supply intakes. This can damage the fittings. Make sure that the water supply hoses are not twisted or bent. A bent or twisted hose can leak and cause an electric shock due to the water leakage. To ensure the correct water usage, connect both hot and cold water faucets. If either or both are not connected, an error code could occur.

Note: If you do not want to use the hot water supply hose, insert a water intake cap into the hot water supply intake hole. In this case you must select the Tap Cold option for the water temperature. No intake cap is provided with your washer. It must be purchased separately.

For connecting the drain hoses of the MIDEA MLTW44A1AWW Top-Load Washer, ensure that the connection between the drain hose and the wash basin, standpipe or laundry tub is not airtight.

For draining over the edge of a wash basin, secure the guide to the side of the basin wall with a hook, tape it or tie it with a piece of cord to prevent the drain hose from moving.

For a standpipe, the standpipe must be no shorter than 39 in. (99 cm) and no longer than 96 in. (244 cm).

For a laundry tub, the laundry tub must be no shorter than 39-in. (99 cm) and no higher than 96-in (244 cm) maximum.

To level the MIDEA MLTW44A1AWW Top-Load Washer, follow these steps:

1. Slide the washer into position.

2. Open the lid of the washer, then pour water into the tub to the leveling circle. If the washer is level, the water will touch the leveling circle all the way around. If the washer is not level, the water will only touch part of the leveling circle.

3. If your washer is not level, carefully tilt your washer just enough to adjust the leveling feet on the bottom front of your washer. Extend the feet only as much as is necessary. If the feet are extended too much, your washer may vibrate.

Caution: Do not use your washing machine without leveling. If your washer is not level, it may vibrate excessively, make excessive noise, or indicate error codes when the washer is running. Extend the leveling feet only as much as is necessary.

To power on the MIDEA MLTW44A1AWW Top-Load Washer, plug the power cord into a well-grounded, 3-prong, 120 Volt 60 Hz approved electrical outlet, protected by a 15-amp fuse or comparable circuit breaker. The washer is grounded through the third prong of the power cord.

Run a test cycle on the MIDEA MLTW44A1AWW Top-Load Washer to make sure it is properly installed by following these steps:

1. Load about 6 pounds (2.7 kg) of laundry into the tub.

2. Select the Cycles knob to turn on your washer.

3. Turn the cycle selector to select the Rinse & Spin cycle.

4. Press the Start Pause button to start the test cycle. Your washer should not rock or vibrate excessively when water fills the tub or when washing or spinning. The washer should drain well during the spin cycle.

Caution: If you detect any water leaks while the washer is filling or draining, check the water connections. If the washer rocks and/or vibrates excessively, level it again.

To use the START/PAUSE BUTTON on the MIDEA MLTW44A1AWW Top-Load Washer, press once to start the program. Press again to pause the program. When paused, you can add a garment, and only Cycles and Water Level could be changed. Once paused, you can open the lid and change cycles and water level, then press the start button again to resume the washer cycle.

If you power on the washer and do not start a cycle within 10 minutes the washer will automatically power off.

To set the Child Lock function on the MIDEA MLTW44A1AWW Top-Load Washer, press and hold both the SOIL LEVEL and TEMP. buttons for three seconds. The Child Lock light will turn on.

Note: If your washer is not turned on, the Child Lock can still remain set. To use your washer when the Child Lock is on, you need to turn off the lock function first.

To turn off the Child Lock function on the MIDEA MLTW44A1AWW Top-Load Washer, press and hold both the SOIL LEVEL and TEMP. buttons for three seconds.

If you turn on the Child Lock function while the washer lid is open on the MIDEA MLTW44A1AWW Top-Load Washer, E3 appears on the display. If you do not close the lid within 20 seconds, your washer sounds an alarm, displays CL, and drains all water in the tub. To clear the alarm, press the Power button to turn off your washer.

The MIDEA MLTW44A1AWW Top-Load Washer is designed to use high efficiency (HE) detergents for the best cleaning results. It is recommended not to use a regular detergent because HE detergents contain suppressors that reduce or eliminate suds, allowing the load to tumble more efficiently and maximizing cleaning.

Before loading laundry into the MIDEA MLTW44A1AWW Top-Load Washer, make sure to remove coins, keys, and other hard objects and close zippers, as these items may damage clothes and the washer. You should sort laundry by fabric type, soil level, color, and load size. Fill the tub with dry, unfolded clothes, and load the tub no more than 3/4 full.

Overloading may reduce washing efficiency, cause excess wear, and possibly cause creasing or wrinkling of the load. Wash delicate items such as bras, hosiery and other lingerie on the Delicates cycle with similar lightweight items. When washing big, bulky items or a few smaller items that do not fill the tub completely, add a few towels to improve spin performance. When washing heavily soiled loads, do not overload your washer to ensure good cleaning results.

To add detergent and additives to the MIDEA MLTW44A1AWW Top-Load Washer:

For Liquid or Powder Detergent:

• Load liquid or powder detergent in the compartment indicated.
• Pour the recommended amount of laundry detergent directly into the compartment before starting your washer.
• If you are using color-safe bleach, add it with the detergent to the detergent compartment.
• When adding color-safe bleach with detergent, both laundry products should be in the same form (liquid).

For PODs:

• First load PODs directly the bottom of an empty basket.
• Then add clothes on top of the PODs.

Loading PODs at the bottom of the basket will improve wash performance and will enable detergent to dissolve more easily in the wash.

For Liquid Bleach (Bleach compartment):

• Add chlorine bleach to the bleach compartment. Do not over-fill the compartment.
• There is no water inlet to the bleach dispenser, so the bleach will directly load into the tub when you pour it in.

Caution: Avoid splashing or over-filling the compartment. Never pour undiluted liquid chlorine bleach directly onto the load or into the tub, as this can damage fabrics. Do not pour color-safe bleach into the bleach compartment; instead, add it to the detergent compartment.

For Fabric Softener (Softener compartment):

• Pour the recommended amount of liquid fabric softener into the softener compartment. The dispenser automatically releases liquid fabric softener at the correct time during the rinse cycle.

Caution: Use the softener compartment ONLY for liquid fabric softeners. Do not use the Downy Ball in the fabric softener compartment. Do not use liquid fabric softener that is too expired as it may not mix with the water sufficiently. Be sure to select the Fabric Softener option when using fabric softener so that it is released in the rinse portion of the cycle.

To set a delayed start time on the MIDEA MLTW44A1AWW Top-Load Washer, program a wash cycle, then press the DELAY button to turn on the delay start time function. Press the Delay button repeatedly to select the delay time you want. The delay start time, in hours, will be shown on the display, in sequence, from 0 to 24, then back to 0. If you want to change the wash cycle settings while you are setting the delay start time, turn the cycle selector. To return to setting the delay start time function, repeat Steps 1 and 2 (referring to the setup steps for the cycle selection).

To start the wash cycle on the MIDEA MLTW44A1AWW Top-Load Washer, press the Start Pause button. As your washer moves from stage to stage in the wash cycle, the related light turns on (such as Rinse or Spin).

If you need to pause the cycle (for example to add or remove items or adjust the load), press the Start Pause button, then open the lid. Your washer stops. When you are ready to resume washing, close the door, then press the Start Pause button.

The maximum load weight for the MIDEA MLTW44A1AWW Top-Load Washer is:

• Agitator: 18.23 lbs. (8.27kg) Dry clothes
• Impeller: 18.65 lbs. (8.46kg) Dry clothes

To clean the exterior of the MIDEA MLTW44A1AWW Top-Load Washer, use a soft cloth to wipe up all detergent, bleach, or other spills as they occur.

To clean the interior of the MIDEA MLTW44A1AWW Top-Load Washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial residue, clean the interior. Failure to follow these instructions may result in unpleasant conditions, including odors or permanent stains in your washer or on your laundry. To remove hard water deposits, use a cleaner labeled “Washer safe”.

To clean the control panel of the MIDEA MLTW44A1AWW Top-Load Washer, clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray cleaners directly on the panel, as the control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your washer and wipe up any spills or over-spray immediately.

To clean the detergent, bleach, or softener compartment of the MIDEA MLTW44A1AWW Top-Load Washer, clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray cleaners directly on the panel, as the control panel finish may be damaged by some laundry pre-treatment soil and stain remover products. Apply such products away from your washer and wipe up any spills or over-spray immediately.

The Tub Clean cycle on the MIDEA MLTW44A1AWW Top-Load Washer is a self-cleaning cycle that removes the causes of odors without using a cleaning agent. It is suggested cleaning the tub about once a month.

Caution: Never use the tub clean cycle when laundry is in your washer. This may damage the laundry or your washer. To use Tub Clean, turn the control knob to power on, turn the cycle selector to Tub Clean, add one cup of chlorine bleach to the bleach dispenser with the tub empty, and press the Start Pause button.

To prepare the MIDEA MLTW44A1AWW Top-Load Washer for storage, you can damage your washer if you do not remove water from hoses and internal components before storage. Follow these steps:

• Select the Quick Wash cycle and add bleach to the washer. Run your washer through the cycle without a load.
• Turn the water faucets off and disconnect the inlet hoses.
• Unplug your washer from the electrical outlet and leave your washer lid open to let air circulate inside the tub.

Caution: If your washer has been stored in below-freezing temperatures, allow time for any leftover water in your washer to dry out before use.

If the MIDEA MLTW44A1AWW Top-Load Washer does not start, check the following:

• Make sure that your washer is plugged in.
• Make sure that the lid is closed.
• Make sure that the water source faucets are open.
• Make sure that you press the Start Pause button to start your washer.
• Before the washer starts to fill, it makes a series of clicking noises to make sure that the lid is locked. The washer doesn’t drain after the lid locks. For automatic cycles, a load sensing program starts before filling and after the lid locks, where the washer will agitate clothing without water to determine load type, water level, and cycle time, then it fills (this can take up to one minute and is normal). For non automatic cycles, the washer fills after the lid locks.
• Check the fuse or reset the circuit breaker.

If the MIDEA MLTW44A1AWW Top-Load Washer has no water or not enough water, check the following:

• Make sure that both faucets are fully turned on.
• Make sure that the water pressure is in the range listed in Water requirements.
• Make sure that the water inlet hoses are not kinked and straighten if necessary.
• Disconnect the hoses and clean the screens, as the hose filter screens may be clogged.
• The MIDEA MLTW44A1AWW is a water efficiency washer and does not fill to the levels of a standard washer; low water levels are normal, and it is normal for parts of clothing to stick out of the water.
• For automatic cycles, before filling and after the lid locks, a load sensing program starts where the washer will agitate clothing without water to determine load type, water level, and cycle time, then it fills. This can take up to one minute and is normal. For non automatic cycles, the washer fills after the lid locks.

If the MIDEA MLTW44A1AWW Top-Load Washer stops:

• Make sure that the power outlet is a working outlet.
• Check the fuse or reset the circuit breaker.
• Close the lid, then press the Start Pause button to start your washer. For your safety, your washer does not spin unless the lid is closed.
• Before your washer starts to fill, it makes a series of clicking noises to make sure that the lid is locked.
• Sometimes your washer may pause between stages in the cycle. Wait to see if your washer starts again.
• Disconnect the inlet hoses and clean the screens periodically, as the hose filter screens may be clogged.

If the lid on the MIDEA MLTW44A1AWW Top-Load Washer is locked or will not open:

• Press the Start Pause button to pause the washer. You cannot open the lid if the washer is running.
• After you pause the washer, it may take a few seconds for the lid lock to release.
• If the lid is locked when your washer is not running, press the Power button to turn on your washer.
• If power fails while your washer is running, when power is restored, the lid unlocks. Your washer waits three minutes then runs the rest of the cycle.

If the MIDEA MLTW44A1AWW Top-Load Washer does not drain or spin, check the following:

• Check the fuse or reset the circuit breaker.
• Close the lid, then press the Start Pause button to start your washer. For your safety, your washer does not spin unless the lid is closed.
• Make sure that the drain hose is not kinked. Straighten as necessary.
• Make sure that the height of the drain hose is within specified limits. See Drainage requirements.
• The pipes to your sewer system may be clogged. Contact a plumber or qualified repair professional.

If the water temperature is not correct on the MIDEA MLTW44A1AWW Top-Load Washer, check the following:

• Make sure that you have selected the correct temp.
• Make sure that the water source faucets are fully opened.
• Make sure that the hoses are connected to the correct faucet and water intake connections on your washer, then flush the lines. See Connect the water hoses.
• Disconnect the hoses and clean the screens. The hose filter screens may be clogged.

If the load on the MIDEA MLTW44A1AWW Top-Load Washer is too wet at the end of the cycle, take the following actions:

• Use a high-efficiency detergent to reduce over-sudsing. See Selecting a detergent.
• The load may be too small. Very small loads (one or two items) may become unbalanced and not spin out completely.

If there are water leaks in the MIDEA MLTW44A1AWW Top-Load Washer, check the following:

• Make sure that all hose connections are tight. See Connect the water hoses and Connect the drain hose.
• Make sure that the end of the drain hose is correctly inserted and secured to the drainage system. See Connect the drain hose.
• Avoid overloading.
• Use a high-efficiency detergent to reduce over-sudsing. See Selecting a detergent.

If there is an oversuds condition in the MIDEA MLTW44A1AWW Top-Load Washer:

• Use a high-efficiency detergent to reduce over-sudsing. See Selecting a detergent.
• If you have “soft” water, reduce the amount of detergent.
• For small or lightly soiled loads, reduce the amount of detergent.

To prevent odor in the MIDEA MLTW44A1AWW Top-Load Washer:

• Periodically run a Tub Clean cycle to clean the tub. See Cleaning the tub.
• Use a high-efficiency detergent to reduce over-sudsing. Excessive suds collect in nooks and crannies and cause odor. See Selecting a detergent.
• Dry the interior of your washer after the total cycle has finished.

Error code E1 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the washer takes more than 30 minutes to fill with water at the low water level, 45 mins at medium water level, or 60 mins at the high water level.

Solutions include:

• Make sure that the lid is not open.
• Make sure that water is not leaking. See No water or not enough water.
• Contact Midea SERVICE center.

Error code E2 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the unit takes more than 10 minutes to drain.

The solution is to see Washer does not drain or spin.

Error code E3 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the lid is open.

The solution is to Close the lid.

Error code E4 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that your washer is out of balance more than three times in spin operation.

Solutions include:

• Relevel the load, if it cannot be solved, Contact Midea servicecenter.

Error code E5 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that your washer is not level or the Impact switch failed.

Solutions include:

• Adjust the washer level refer to installation.
• If the situation continues call Midea service center.

Error code F2 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the EEPROM failed.

The solution is to Contact Midea servicecenter.

Error code F5 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the Load sensing failed.

The solution is to Contact Midea servicecenter.

Error code F8 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the Water level sensor failed.

The solution is to Contact Midea servicecenter.

Error code Fd on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the Lid lock failed.

The solution is to Contact Midea servicecenter.

Error code C9 on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the PCB failed.

The solution is to Contact Midea servicecenter.

Error code CL on the MIDEA MLTW44A1AWW Top-Load Washer indicates that the lid has been open for over 20 seconds with the Child Lock function activated.

Solutions include:

• Press the Power button to turn off your washer.
• Turn off the Child Lock function. See Setting the Child Lock.
• Contact Midea service center.

If the MIDEA MLTW44A1AWW Top-Load Washer displays error code E1 after filling, indicating the water level has not changed in 10 minutes:

• Make sure that the lid is not open.
• Make sure that water is not leaking. See No water or not enough water.
• If the washer does not drain, see Washer does not drain or spin.
• Contact Midea SERVICE center.