MIDEA MLC27N3AWW (01) PDF Document

Before washing clothes for the first time, the MIDEA MLC27N3AWW must be operated through one full wash procedure without any clothes inside. To do this, connect the power source and water, put a small amount of detergent into the detergent box, press the On/Off button, and then press the Start/Pause button.

Step 1. Check if the legs are closely attached to the cabinet. If not, turn them to their original positions and tighten the nuts with a spanner.

Step 2. Press the four corners on the top cover of the MIDEA MLC27N3AWW in sequence. If the unit is not stable, the corresponding leg must be adjusted.

Step 3. Loosen the lock nut with a spanner and turn the leg by hand until it closely contacts the floor. Press the leg with one hand and fasten the nut tightly to the cabinet with the other hand.

Step 4. After locking, press the four corners again to confirm stability. If it is still unstable, repeat the adjustment process.

Step 5. As a final check, place a solid cylinder, such as a pop can, on the top cover. If the cylinder remains stable, the MIDEA MLC27N3AWW is level. If it rolls, the unit is not level; adjust the legs in the direction of the lower ground surface until the unit is level.

Step 1. Press down the arrow location on the softener cover inside the drawer.

Step 2. Lift the clip up to remove the softener cover and wash all grooves with water.

Step 3. Restore the softener cover and push the drawer back into position.

To clean the tap filter: First, close the tap. Second, select any procedure except Wash or Drain. Third, press the Start/Pause button and keep the procedure running for about 40 seconds. Fourth, remove the inlet pipe from the tap and use water to wash the filter. Finally, reconnect the inlet pipe.

To clean the filter inside the MIDEA MLC27N3AWW: First, unscrew the inlet pipe from the backside of the machine. Second, pull out the filter using long nose pliers and reinstall it after cleaning. Third, reconnect the inlet pipe, open the tap, and ensure there is no water leakage.

To activate the child lock, press the Soil level and Dry buttons together for three seconds. When active, all buttons except the On/Off button will not work. To release the child lock, press the same two buttons together again for three seconds until the buzzer beeps.

Step 1. Select the desired wash program.

Step 2. Press the Delay button repeatedly to choose the desired delay time (up to 24 hours).

Step 3. Press Start/Pause to begin the delay operation.

This operation can be executed during the wash cycle. Press and hold the Start/Pause button for 3 seconds to trigger the reload function. Wait until the drum stops rotation and the door lock is unlocked. Add the clothes, close the door, and press the Start/Pause button again to resume the cycle.

The MIDEA MLC27N3AWW contains a drain pump filter that may be blocked by foreign matters such as coins or safety pins. To check this: First, use a flat blade screwdriver to open the service panel. Second, rotate the emergency drain hose 90 degrees and pull it out, removing the cap to drain the water into a container. Third, turn the filter counter-clockwise to open it and remove any extraneous matter. Finally, close the filter and the lower cover cap.

The MIDEA MLC27N3AWW features the following wash programs:

Normal: For hard-wearing textiles, heat-resistant textiles made of cotton or linen.

Heavy Duty: For washing heavy clothing like towels.

Bulky: For washing large clothing.

Sports Wear: For washing activewear.

Spin Only: Provides an extra spin with adjustable speed.

Rinse & Spin: Provides an extra rinse with spin.

Washer Clean: Cleans the drum and tube using high-temperature sterilization.

Quick Wash: For lightly soiled laundry.

Delicates: For delicate, washable textiles like silk, satin, synthetic fibers, or blended fabrics.

Sanitary: Uses hot wash for difficult-to-clean clothes.

Baby Wear: For baby clothes to improve rinse performance and protect baby skin.

Wool: For wool textiles labeled with Machine Wash.

Perm Press: Uses moderate wash strength to reduce wrinkles.

Dry Only: Used to dry clothes.

Wash & Dry: Used to wash and dry clothes.

If the MIDEA MLC27N3AWW cannot start, check if the door is closed, the power plug is inserted, the water supply is open, and the buttons are pressed.

If the door cannot be opened, the safety protection is working; disconnect the power.

If water is leaking, check and fasten the water pipes and clean the outlet hose.

If detergent residues appear in the box, clean and wipe the detergent box or use liquid detergent.

If there is abnormal noise or vibration, check if transportation bolts were removed, the machine is on a solid level floor, and the legs are adjusted properly.

If the MIDEA MLC27N3AWW shows error code E30, the door is not closed properly. If E10 appears, there is a water injecting problem; check if water pressure is low or the inlet valve is blocked. If E21 appears, there is overtime water draining; check if the drain hose is blocked. If E12 appears, there is a water overflow; restart the washer.