KARCHER SC 5 EASYFIX PREMIUM IRON (01) PDF Document

To install accessories on your KARCHER SC 5 EASYFIX PREMIUM IRON, please follow these steps:

Step 1. Open the cover on the device socket.

Step 2. Connect the steam connector to the device socket so that the steam connector audibly engages.

Step 3. Push the open end of the accessory onto the steam gun so that the unlocking button on the steam gun engages.

Step 4. Push the open end of the accessory onto the spotlight nozzle.

Step 5. Connect the extension tubes with the steam gun:

a. Push the first extension tube onto the steam gun so that the unlocking button on the steam gun engages. The connection pipe is connected.

b. Push the 2nd extension tube onto the 1st extension tube. The connection pipes are connected.

Step 6. Push the accessory and/or the floor nozzle onto the free end of the extension tube. The accessory is connected.

Step 1. Set the child lock to the rear. The steam lever is locked.

Step 2. Push the cover on the device socket down and disconnect the steam connector from the device socket.

Step 3. Push the unlocking button and pull the parts apart.

For your KARCHER SC 5 EASYFIX PREMIUM IRON, please note the following ATTENTION notice: Unsuitable water can block the nozzles or damage the water level indicator.

Do not fill in pure distilled water. Use a maximum of 50% distilled water mixed with tap water.

Do not use condensation from the clothes dryer for filling.

Do not use collected rainwater for filling.

Do not use cleaning agents or other additives (e.g. scents) for filling.

Step 1. Pull the water reservoir vertically upwards.

Step 2. Fill the water tank vertically with tap water or a mixture of tap water and no more than 50% distilled water up to the “MAX” mark.

Step 3. Insert the water reservoir and press downwards until it locks into place.

Fill tap water or a mixture of tap water and no more than 50% distilled water from a vessel into the filling hole of the water reservoir up to the “MAX” mark.

Note: If there is no or too little water in the steam boiler, the water pump starts to run and pumps water from the water reservoir into the steam boiler. The filling process can take several minutes. Additionally, the device briefly closes the valve every 60 seconds causing an audible soft click. This prevents the valve from clogging and does not affect the steam output.

Step 1. Place the device on a firm surface.

Step 2. Insert the mains plug into a socket.

Step 3. Turn the selector switch from the OFF position to the steam setting selection range. The green heating indicator light flashes.

Step 4. Wait until the green heating indicator stays on.

Step 5. Press the steam lever. Steam leaks out.

The expelled steam volume is regulated using the selector switch for steam volume. The selector switch has setting options from min. steam stage for light soiling to max. steam stage for heavy soiling. The VapoHydro function is for the removal of heavy soiling in areas that are difficult to access.

Step 1. Set the selector switch for the steam volume to the required steam volume.

Step 2. Press the steam lever.

Step 3. Before starting cleaning, point the steam gun at a cloth until steam is expelled evenly.

Step 1. Turn the trigger to the “OFF” position. The device is switched off.

Step 2. Press the steam lever until no more steam flows out. The steam boiler is depressurised.

Step 3. Set the child lock to the rear. The steam lever is locked.

Step 4. Push the cap on the device socket down and disconnect the steam connector from the device socket.

Step 5. Pull the mains plug out of the socket.

Step 6. Drain the water reservoir.

Rinse the KARCHER SC 5 EASYFIX PREMIUM IRON’s steam boiler out after every eighth filling of the tank.

Step 1. Switch the device off.

Step 2. Allow the device to cool down.

Step 3. Drain the water reservoir.

Step 4. Remove the accessory/accessories from the accessory holders.

Step 5. Open the cap of the accessory compartment.

Step 6. Remove the accessory/accessories from the accessory compartment.

Step 7. Open the maintenance lock. To do this, place the open end of an extension tube on the maintenance lock, insert this into the guide so it engages and open it.

Step 8. Fill the steam boiler with water and swing it around vigorously. Lime residue which has been deposited on the bottom of the steam boiler will be released as a result.

Step 9. Drain the water completely out of the steam boiler.

Step 1. Store the round brush in the accessory compartment.

Step 2. Connect a manual nozzle to one extension tube.

Step 3. Connect the extension tubes to the accessory holders.

Step 4. Insert the spotlight nozzle in the storage for accessories.

Step 5. Hang the floor nozzle in the park bracket.

Step 6. Wind the steam hose around the extension tube and connect the steam gun to the floor nozzle.

Step 7. Store the mains cable in the storage for the mains cable.

Step 8. Store the device in a dry location that is protected from frost.

Cleaning the floor areas: We recommend sweeping the floor or vacuum cleaning it before using the appliance. This way the floor will be cleared of dirt and loose particles before the wet cleaning.

Freshening up textiles: Prior to using the appliance, always check the compatibility of the textiles at a concealed point: Steam down the textile, allow it to dry and then check it for any change in colour or shape.

Cleaning coated or painted surfaces: ATTENTION: Damaged surfaces. Steam can loosen wax, furniture polish, plastic coatings or paint and edge band from edges. Do not direct the steam at glued laminated edges as the edge band may loosen. Do not use the appliance for cleaning unsealed wood or parquet floors. Do not use it for cleaning painted or plastic coated surfaces such as kitchen or living room furniture, doors or parquet. To clean these surfaces, steam a cloth briefly and use it to wipe over the surfaces.

Glass cleaner: ATTENTION: Glass breakages and damaged surfaces. Steam can damage sealed points of the window frame and, at low outside temperatures, lead to tension on the surface of window panes and hence to glass breakages. Do not direct the steam at sealed points on the window frame. At low outside temperatures, heat up the window panes by gently steaming the full surface of the glass. Clean the window area with a manual nozzle and cover. To remove the water, use a squeegee or wipe the surfaces dry.

Steam gun: The steam gun can be used for removing slight creases from hanging clothing items (steam from 10-20 cm distance) and for wiping damp dust (steam a cloth briefly and wipe over furniture).

Spotlight nozzle: Suitable for cleaning difficult to access areas, joins, fittings, drains, sinks, WCs, blinds, or radiators. The closer the nozzle is to the soiled area, the greater the cleaning efficiency. Treat larger lime deposits with a suitable detergent before steam cleaning (let it soak for approx. 5 minutes then steam it off).

Round brush (small): Used for cleaning stubborn dirt. It can be removed more easily by brushing. ATTENTION: The brush may scratch sensitive surfaces and is not suitable for cleaning them.

Round brush (large): Suitable for cleaning large rounded surfaces like wash basins, shower trays, bath tubs, and kitchen sinks. ATTENTION: The brush may scratch sensitive surfaces and is not suitable for cleaning them.

Power nozzle: Used for cleaning stubborn dirt, blowing down corners, joins, etc.

Manual nozzle: Used for cleaning small areas that can be washed down, shower cubicles, and mirrors.

Floor nozzle: Used for cleaning washable wall and floor coverings like stone floors, tiles, and PVC floors. ATTENTION: Damage due to build-up of steam can occur. Check heat resistance and steam effect on an inconspicuous area before use.

ATTENTION: Beware of damaging the carpet glider and carpet. Contamination on the carpet glider, as well as heat and moisture penetration, can result in the carpet being damaged.

Prior to application, check the heat resistance and impact of steam on the carpet at an insignificant spot with a small amount of steam.

Observe the cleaning instructions from the carpet manufacturer.

Ensure the carpet has been vacuumed and stains have been removed before using the carpet glider.

Remove any possible water accumulation (condensate) in the appliance by evaporating it into a drain before application and after operating pauses.

Only use the carpet glider with a floor cleaning cloth on the floor nozzle.

Steam clean with a weak steam stage.

Do not direct the steam continuously onto one spot (maximum 5 seconds) to avoid over-moistening and damage.

Do not use the carpet glider on deep-pile carpets.

Initial Startup: ATTENTION: Material damage due to condensate/moisture may cause damage to sensitive floor coverings. If possible, perform ironing on a floor covering insensitive to condensation (e.g. tiles/stone). For sensitive floor coverings, ensure the area is adequately protected. The iron plate must be hot to prevent steam from condensing and dripping. Do not turn on the VapoHydro steam stage when the iron is plugged in, as the laundry will get wet.

Recommended Steam Stages:

Procedure:

Step 1. Ensure tap water or a mixture of tap water and no more than 50% distilled water is in the steam boiler.

Step 2. Insert the steam plug of the iron into the unit plug until it clicks into place.

Step 3. Put the steam cleaner into operation.

Step 4. Wait until the steam cleaner is ready for use.

Step 5. The iron is ready for use as soon as the indicator light (orange) has gone out.

Step 6. The warning light comes on during use when the iron is reheating. The application must not be interrupted during reheating.

Steam Ironing: ATTENTION: Failure to observe the ironing information in the garment may result in damage. With the fixed, optimal temperature setting, all ironable textiles can be ironed without additional temperature setting. Smooth delicate fabrics and imprints on the back with steam without direct contact. Steaming fabrics at a distance of 2 to 3 cm will gently straighten the fibres. The iron is fitted with an automatic switch-off if not moved for more than 5 minutes. The iron can be held vertically for steaming curtains, dresses, etc.

Dry Ironing: ATTENTION: Water shortage in the steam boiler leads to damage to the device. Ensure there is water in the steam boiler. Failure to observe the ironing information in the garment may result in damage. Delicate fabrics and prints should not be dry ironed. Wait until the heating indicator light (orange) of the iron goes out. The iron is ready for ironing.

Descaling the steam boiler is not required if commercially available distilled water is used. Since lime clogs the appliance, we recommend descaling the appliance based on the number of times the water reservoir is filled as specified in the table (TF=tank fillings).

Your water board or municipal utilities authority can provide information on the hardness of tap water.

Descaling Procedure:

ATTENTION: The descaler may corrode sensitive surfaces. Fill and empty the appliance carefully.

Step 1. Switch off the device.

Step 2. Allow the device to cool down.

Step 3. Drain the water reservoir.

Step 4. Remove the accessory/accessories from the accessory holders.

Step 5. Open the cap of the accessory compartment.

Step 6. Remove the accessory from the accessory compartment.

Step 7. Open the maintenance lock using an extension tube.

Step 8. Drain the water completely out of the steam boiler.

ATTENTION: Appliance damage due to descaler. An unsuitable descaler or incorrect dosing may damage the appliance. Only use KÄRCHER descaler. Use 1 dosing unit of the descaler for 0.5 l water.

Step 9. Apply descaler solution according to the details.

Step 10. Fill the descaler solution into the steam boiler. Do not seal the steam boiler.

Step 11. Allow the descaler solution to take effect for approx. 8 hours.

Step 12. Drain the descaler solution completely out of the steam boiler.

Step 13. Repeat the descaling process if necessary.

Step 14. Rinse the steam boiler 2-3 times with cold water to drain all descaler solution residue.

Step 15. Drain the water completely out of the steam boiler.

Step 16. Dry the mounting for the grid connection cable.

Step 17. Close the maintenance lock with an extension tube.

The micro fibre cloths are not suitable for the dryer. When washing the cloths, observe the instructions on the washing tag. Do not use any liquid softeners as this will affect the ability of the cloths to pick up dirt.

Wash the floor cleaning cloths and covers at a max. temperature of 60 °C in the washing machine.

This indicates there is no water in the tank. Fill the water reservoir up to the “MAX” marking.

This means there is no water in the steam boiler and the pump’s overheat protection has triggered.

Step 1. Switch the device off.

Step 2. Fill the water reservoir.

Step 3. Switch on the device.

It can also mean the water tank is not inserted correctly or is calcified.

Step 1. Remove the water reservoir.

Step 2. Rinse the water reservoir.

Step 3. Insert the water reservoir and press downwards until it locks into place.

The steam lever is locked with the child lock. Set the child lock (selector switch for steam volume) to the front. The steam lever will be released.

A long heating-up time or high water output indicates that the steam boiler is scaled. You should descale the steam boiler.

For high water output, it could also be that the VapoHydro steam stage is set. In this case, turn the selector switch to the steam setting selection range.

If the steam pressure iron “spits” water, you need to rinse or descale the steam boiler of the steam cleaner.

If water droplets come out after ironing breaks, it means that during longer ironing breaks, steam can condense in the steam line. After pauses in the ironing process, direct the blast of steam onto a cloth until the steam flows evenly.