KARCHER SC 5 EASYFIX PREMIUM (01) PDF Document

The KARCHER SC 5 EASYFIX PREMIUM has several safety devices for your protection. You should never modify or bypass these safety devices.

Pressure controller: This keeps the pressure in the steam boiler as constant as possible during operation. The heating switches off when the maximum operating pressure is reached and activates again if there is a pressure drop from steam removal.

Safety thermostat: This prevents the device from overheating. If the pressure regulator and boiler thermostat fail and the unit overheats, the safety thermostat switches the unit off. For resetting, contact the responsible KÄRCHER Customer Service.

Boiler thermostat: This switches off the heating in the event of a fault, for example, if there is no water in the steam boiler and the temperature rises. The device is ready for use again as soon as you refill the water.

Maintenance lock: This seals the steam boiler from the steam pressure. It is also a pressure relief valve. If the pressure regulator is defective and the steam pressure rises, the valve opens and steam escapes through the lock. Prior to restarting, contact the responsible KÄRCHER Customer Service.

Step 1. Open the cover on the device socket.

Step 2. Connect the steam connector to the device socket so that the steam connector audibly engages.

Step 3. Push the open end of the accessory onto the steam gun so that the unlocking button on the steam gun engages.

Step 4. To attach an accessory to the spotlight nozzle, push the open end of the accessory onto the spotlight nozzle.

Step 5. To connect the extension tubes with the steam gun:

a) Push the first extension tube onto the steam gun so that the unlocking button on the steam gun engages. The connection pipe is connected.

b) Push the second extension tube onto the first extension tube. The connection pipes are connected.

Step 6. Push the accessory and/or the floor nozzle onto the free end of the extension tube. The accessory is connected.

Step 1. Set the child lock to the rear. The steam lever is now locked.

Step 2. Push the cover on the device socket down and disconnect the steam connector from the device socket.

Step 3. Push the unlocking button and pull the parts apart.

ATTENTION: Damage to the device. Unsuitable water can block the nozzles or damage the water level indicator. Do not fill in pure distilled water. Use a maximum of 50% distilled water mixed with tap water. Do not use condensation from a clothes dryer, collected rainwater, cleaning agents, or other additives (e.g. scents).

To remove the water reservoir for filling:

Step 1. Pull the water reservoir vertically upwards.

Step 2. Fill the water tank vertically with tap water or a mixture of tap water and no more than 50% distilled water up to the “MAX” mark.

Step 3. Insert the water reservoir and press downwards until it locks into place.

To fill the water reservoir directly on the device:

Step 1. Fill tap water or a mixture of tap water and no more than 50% distilled water from a vessel into the filling hole of the water reservoir up to the “MAX” mark.

Note: If there is no or too little water in the steam boiler, the water pump starts and pumps water from the water reservoir into the steam boiler. The filling process can take several minutes.

Note: The device briefly closes the valve every 60 seconds causing an audible soft click. This prevents the valve from clogging and does not affect the steam output.

Step 1. Place the device on a firm surface.

Step 2. Insert the mains plug into a socket.

Step 3. Turn the selector switch from the OFF position to the steam setting selection range. The green heating indicator light will flash.

Step 4. Wait until the green heating indicator stays on.

Step 5. Press the steam lever. Steam will leak out.

The expelled steam volume is regulated using the selector switch for steam volume. The selector switch has options from a minimum steam stage for light soiling to a maximum steam stage for heavy soiling. The VapoHydro function is for removing heavy soiling in areas that are difficult to access.

Step 1. Set the selector switch for the steam volume to the required steam volume.

Step 2. Press the steam lever.

Step 3. Before starting cleaning, point the steam gun at a cloth until steam is expelled evenly.

Step 1. Turn the trigger to the “OFF” position. The device is switched off.

Step 2. Press the steam lever until no more steam flows out. The steam boiler is now depressurised.

Step 3. Set the child lock to the rear. The steam lever is locked.

Step 4. Push the cap on the device socket down and disconnect the steam connector from the device socket.

Step 5. Pull the mains plug out of the socket.

Step 6. Drain the water reservoir.

You should rinse the device’s steam boiler out after every eighth filling of the tank.

Step 1. Switch the device off (see chapter “Switching off the device”).

Step 2. Allow the device to cool down.

Step 3. Drain the water reservoir.

Step 4. Remove the accessories from the accessory holders.

Step 5. Open the cap of the accessory compartment.

Step 6. Remove the accessories from the accessory compartment.

Step 7. Open the maintenance lock. To do this, place the open end of an extension tube on the maintenance lock, insert it into the guide so it engages, and open it.

Step 8. Fill the steam boiler with water and swing it around vigorously. This will release lime residue deposited on the bottom of the steam boiler.

Step 9. Drain the water completely out of the steam boiler.

Step 1. Store the round brush in the accessory compartment.

Step 2. Connect a manual nozzle to one extension tube.

Step 3. Connect the extension tubes to the accessory holders.

Step 4. Insert the spotlight nozzle in the storage for accessories.

Step 5. Hang the floor nozzle in the park bracket.

Step 6. Wind the steam hose around the extension tube and connect the steam gun to the floor nozzle.

Step 7. Store the mains cable in the storage for the mains cable.

Step 8. Store the device in a dry location that is protected from frost.

Cleaning the floor areas: We recommend sweeping the floor or vacuum cleaning it before using the appliance. This will clear the floor of dirt and loose particles before the wet cleaning.

Freshening up textiles: Prior to use, always check the compatibility of textiles at a concealed point. Steam down the textile, allow it to dry, and then check it for any change in colour or shape.

Cleaning coated or painted surfaces: ATTENTION: Damaged surfaces. Steam can loosen wax, furniture polish, plastic coatings, paint, and edge bands from edges. Do not direct the steam at glued laminated edges as the edge band may loosen. Do not use the appliance for cleaning unsealed wood or parquet floors. For painted or plastic coated surfaces like kitchen furniture, doors or parquet, steam a cloth briefly and use it to wipe over the surfaces.

Glass cleaner: ATTENTION: Glass breakages and damaged surfaces. Steam can damage sealed points of the window frame and, at low outside temperatures, lead to tension on window panes, causing glass breakages. Do not direct steam at sealed points on the window frame. At low outside temperatures, heat up window panes by gently steaming the full surface of the glass. Clean the window area with a manual nozzle and cover. Use a squeegee or wipe the surfaces dry to remove water.

Steam gun: Can be used without accessories for:

● Removing slight creases from hanging clothing: Steam the item from a distance of 10-20 cm.

● Wiping damp dust: Briefly steam a cloth and use it to wipe over furniture.

Spotlight nozzle: Suitable for cleaning hard-to-access areas, joints, fittings, drains, sinks, WCs, blinds, or radiators. The closer the nozzle is to the soiled area, the greater the cleaning efficiency. Slide it onto the steam gun.

Round brush (small & large): Used for cleaning stubborn dirt. Brushing helps remove it more easily. ATTENTION: The brush may scratch sensitive surfaces. Fit the brush to the spotlight nozzle.

Power nozzle: Used for stubborn dirt, blowing down corners, joints, etc. Install it onto the spotlight nozzle like the round brush.

Manual nozzle: Used for cleaning small washable areas, shower cubicles, and mirrors. Push it onto the steam gun and pull the cover over it.

Floor nozzle: Used for washable wall and floor coverings like stone floors, tiles, and PVC. Check heat resistance on an inconspicuous area first. We recommend sweeping or vacuuming before use. Work slowly on heavily soiled surfaces.

Step 1. Connect the extension tubes with the steam gun.

Step 2. Push the floor nozzle onto the extension tube.

Step 3. Fasten the floor cleaning cloth to the nozzle by placing the cloth on the floor (hook and loop fastener strips up) and placing the nozzle onto it with slight pressure.

Step 4. To remove the cloth, place one foot on the bottom corner and lift the nozzle up.

The carpet glider is used for freshening up carpets.

ATTENTION: Contamination on the glider, as well as heat and moisture, can damage the carpet. Before use, check heat resistance and steam impact on an insignificant spot. Observe cleaning instructions from the carpet manufacturer. Ensure the carpet has been vacuumed and stains removed before use.

● Only use the carpet glider with a floor cleaning cloth on the floor nozzle.

● Steam clean with a weak steam stage.

● Do not direct steam continuously onto one spot (maximum 5 seconds).

● Do not use on deep-pile carpets.

Fastening the carpet glider to the floor nozzle:

Step 1. Fasten the floor cleaning cloth to the floor nozzle.

Step 2. Using a little force, allow the floor nozzle to slide into the carpet glider and engage there.

Step 3. Start cleaning the carpet.

Removing the carpet glider from the floor nozzle:

CAUTION: Beware of burns to your feet. The carpet glider can heat up. Do not operate or remove it bare-footed or with open sandals. Only use suitable footwear.

Step 1. Press the strap on the carpet glider downwards using your toecap.

Step 2. Lift the floor nozzle upwards.

ATTENTION: Material damage due to condensate/moisture. Ironing may cause condensation to drip and damage sensitive floor coverings. If possible, perform ironing on a floor covering insensitive to condensation (e.g., tiles/stone). For sensitive floors, ensure the area is adequately protected (e.g., water-impermeable floor mat).

Note: The iron plate must be hot to prevent steam from condensing and dripping. Do not turn on the VapoHydro steam stage when the iron is plugged in, as this will get the laundry wet.

Startup Procedure:

Step 1. Ensure tap water or a mixture with no more than 50% distilled water is in the steam boiler.

Step 2. Insert the steam plug of the iron into the unit until it clicks into place.

Step 3. Put the steam cleaner into operation.

Step 4. Wait until the steam cleaner is ready for use.

Step 5. The iron is ready for use as soon as the indicator light (orange) has gone out.

Step 6. The warning light comes on during use when the iron is reheating. The application must not be interrupted.

Steam Ironing

ATTENTION: Damage to garments. Observe the ironing information in the garment.

Note: With the fixed, optimal temperature setting, all ironable textiles can be ironed without additional temperature setting. Smooth delicate fabrics and imprints on the back with steam without direct contact. Steaming fabrics at a distance of 2 to 3 cm will gently straighten the fibres.

Note: The iron has an automatic switch-off that activates if it has not been moved for more than 5 minutes, increasing safety and saving energy. It will switch back on as soon as it is moved.

Step 1. As soon as the heating indicator light (orange) of the iron goes out, ironing can be started.

Step 2. Press the steam switch on the handle below. Steam emits as long as the switch is pressed.

Step 3. Before ironing and after pauses, direct the blast of steam onto a cloth until the steam flows evenly.

Dry Ironing

ATTENTION: Water shortage in the steam boiler leads to damage to the device. Make sure there is water in the steam boiler.

ATTENTION: Damage to garments. Observe the ironing information in the garment.

Note: Delicate fabrics and prints should not be dry ironed.

● Wait until the heating indicator light (orange) of the iron goes out. The iron is ready for ironing.

Note: Descaling is not required if commercially available distilled water is used. Since lime clogs the appliance, we recommend descaling based on the number of times the water reservoir is filled, according to the table below. Your water board can provide information on tap water hardness.

ATTENTION: Damaged surfaces. The descaler may corrode sensitive surfaces. Fill and empty the appliance carefully.

ATTENTION: Appliance damage due to descaler. An unsuitable descaler or incorrect dosing may damage the appliance. Only use KÄRCHER descaler. Use 1 dosing unit of the descaler for 0.5 l water.

Step 1. Switch off the device.

Step 2. Allow the device to cool down.

Step 3. Drain the water reservoir.

Step 4. Remove accessories from the accessory holders.

Step 5. Open the cap of the accessory compartment.

Step 6. Remove the accessory from the accessory compartment.

Step 7. Open the maintenance lock. To do this, place the open end of an extension tube on the lock, insert it into the guide, and open it.

Step 8. Drain the water completely out of the steam boiler.

Step 9. Apply descaler solution according to the details.

Step 10. Fill the descaler solution into the steam boiler. Do not seal the steam boiler.

Step 11. Allow the descaler solution to take effect for approx. 8 hours.

Step 12. Drain descaler solution completely out of the steam boiler.

Step 13. Repeat the descaling process if necessary.

Step 14. Rinse the steam boiler 2-3 times with cold water to drain all the descaler solution residue.

Step 15. Drain the water completely out of the steam boiler.

Step 16. Dry the mounting for the grid connection cable.

Step 17. Close the maintenance lock with an extension tube.

Note: The micro fibre cloths are not suitable for the dryer.

Note: When washing the cloths, observe the instructions on the washing tag. Do not use any liquid softeners as this will affect the ability of the cloths to pick up dirt.

Step 1. Wash the floor cleaning cloths and covers at a maximum temperature of 60 °C in the washing machine.

This indicates there is no water in the tank.

● Fill the water reservoir up to the “MAX” marking.

This means there is no water in the steam boiler and the pump’s overheat protection has triggered, or the water tank is not inserted correctly or is calcified.

For no water in the boiler:

Step 1. Switch the device off.

Step 2. Fill the water reservoir.

Step 3. Switch on the device.

If the water tank is not inserted correctly:

Step 1. Remove the water reservoir.

Step 2. Rinse the water reservoir.

Step 3. Insert the water reservoir and press downwards until it locks into place.

The steam lever is locked with the child lock.

● Set the child lock (selector switch for steam volume) to the front. The steam lever is now released.

The steam boiler is likely scaled (has lime buildup). You need to descale the steam boiler.

If you are experiencing high water output, also check if the VapoHydro steam stage is set. If so, turn the selector switch to the steam setting selection range.

If the iron “spits” water, the steam boiler of the steam cleaner needs to be rinsed or descaled.

If water droplets come out after ironing breaks, it is because steam can condense in the steam line during longer breaks.

● After pauses in the ironing process, direct the blast of steam onto a cloth until the steam flows evenly.

Electrical connection

Performance data

Filling quantity

Dimensions and weights

Subject to technical modifications.