KARCHER SC 5 EASYFIX (01) PDF Document

To install accessories on your KARCHER SC 5 EASYFIX, please follow these steps:

1. Open the cover on the device socket.

2. Connect the steam connector to the device socket so that the steam connector audibly engages.

3. Push the open end of the accessory onto the steam gun so that the unlocking button on the steam gun engages.

4. Push the open end of the accessory onto the spotlight nozzle.

5. Connect the extension tubes with the steam gun:

a. Push the first extension tube onto the steam gun so that the unlocking button on the steam gun engages. The connection pipe is connected.

b. Push the 2nd extension tube onto the 1st extension tube. The connection pipes are connected.

6. Push the accessory and/or the floor nozzle onto the free end of the extension tube. The accessory is connected.

1. Set the child lock to the rear. The steam lever is locked.

2. Push the cover on the device socket down and disconnect the steam connector from the device socket.

3. Push the unlocking button and pull the parts apart.

The water reservoir of your KARCHER SC 5 EASYFIX can be removed for filling or be filled directly on the device.

ATTENTION: Unsuitable water can block the nozzles or damage the water level indicator. Do not fill with pure distilled water. Use a maximum of 50% distilled water mixed with tap water. Do not use condensation from the clothes dryer for filling. Do not use collected rain water for filling. Do not use cleaning agents or other additives (e.g. scents) for filling.

To remove the water reservoir for filling:

1. Pull the water reservoir vertically upwards.

2. Fill the water tank vertically with tap water or a mixture of tap water and no more than 50% distilled water up to the “MAX” mark.

3. Insert the water reservoir and press downwards until it locks into place.

To fill the water reservoir directly on the device:

1. Fill tap water or a mixture of tap water and no more than 50% distilled water from a vessel into the filling hole of the water reservoir up to the “MAX” mark.

Note: If there is no or too little water in the steam boiler, the water pump starts to run and pumps water from the water reservoir into the steam boiler. The filling process can take several minutes.

Note: The device briefly closes the valve every 60 seconds causing an audible soft click. Closing prevents the valve from clogging. This does not affect the steam output.

1. Place the device on a firm surface.

2. Insert the mains plug into a socket.

3. Turn the selector switch from the OFF position to the steam setting selection range. The green heating indicator light flashes.

4. Wait until the green heating indicator stays on.

5. Press the steam lever. Steam leaks out.

The expelled steam volume is regulated using the selector switch for steam volume. The selector switch has setting options from min. steam stage for light soiling to max. steam stage for heavy soiling. The VapoHydro function is for the removal of heavy soiling in areas that are difficult to access.

1. Set the selector switch for the steam volume to the required steam volume.

2. Press the steam lever.

3. Before starting cleaning, point the steam gun at a cloth until steam is expelled evenly.

If there is not enough water, the water shortage indicator lamp flashes red and a signal tone sounds.

Note: The water pump fills the steam boiler at intervals. If the filling is successful, the red water shortage indicator lamp goes out.

Note: If there is no or too little water in the steam boiler, the water pump starts to run and pumps water from the water reservoir into the steam boiler. The filling process can take several minutes.

ATTENTION: Damage to the device

Unsuitable water can block the nozzles or damage the water level indicator.

1. Fill the water tank with tap water or a mixture of tap water and no more than 50% distilled water up to the “MAX” mark. The device is ready for use.

1. Turn the trigger to the “OFF” position. The device is switched off.

2. Press the steam lever until no more steam flows out. The steam boiler is depressurised.

3. Set the child lock to the rear. The steam lever is locked.

4. Push the cap on the device socket down and disconnect the steam connector from the device socket.

5. Pull the mains plug out of the socket.

6. Drain the water reservoir.

Rinse the device’s steam boiler out after every eighth filling of the tank.

1. Switch the device off; see Chapter Switching off the device.

2. Allow the device to cool down.

3. Drain the water reservoir.

4. Remove the accessory/accessories from the accessory holders.

5. Open the cap of the accessory compartment.

6. Remove the accessory/accessories from the accessory compartment.

7. Open the maintenance lock. To do this place the open end of an extension tube on the maintenance lock, insert this into the guide so it engages and open it.

8. Fill the steam boiler with water and swing it around vigorously. Lime residue which has been deposited on the bottom of the steam boiler will be released as a result.

9. Drain the water completely out of the steam boiler.

1. Store the round brush in the accessory compartment.

2. Connect a manual nozzle to one extension tube.

3. Connect the extension tubes to the accessory holders.

4. Insert the spotlight nozzle in the storage for accessories.

5. Hang the floor nozzle in the park bracket.

6. Wind the steam hose around the extension tube and connect the steam gun to the floor nozzle.

7. Store the mains cable in the storage for the mains cable.

8. Store the device in a dry location that is protected from frost.

Cleaning the floor areas: We recommend sweeping the floor or vacuum cleaning it before using the appliance. In this way the floor will be cleared of dirt and loose particles before the wet cleaning.

Freshening up textiles: Prior to using the appliance, always check the compatibility of the textiles at a concealed point: Steam down the textile, allow it to dry and then check it for any change in colour or shape.

Cleaning coated or painted surfaces: ATTENTION: Steam can loosen wax, furniture polish, plastic coatings or paint and edge band from edges. Do not direct the steam at glued laminated edges as the edge band may loosen. Do not use the appliance for cleaning unsealed wood or parquet floors. To clean these surfaces, steam a cloth briefly and use it to wipe over the surfaces.

Glass cleaner: ATTENTION: Steam can damage sealed points of the window frame and, at low outside temperatures, lead to tension on the surface of window panes and hence to glass breakages. Do not direct the steam at sealed points on the window frame. At low outside temperatures, heat up the window panes by gently steaming the full surface of the glass. Clean the window area with a manual nozzle and cover. To remove the water, use a squeegee or wipe the surfaces dry.

Steam gun: The steam gun can be used for the following applications without accessories:

• For removing slight creases from the hanging clothing items: Steam the clothing item from a distance of 10-20 cm.

• For wiping damp dust: Steam a cloth briefly and use it to wipe over the furniture.

Spotlight nozzle: Suitable for cleaning areas, joins, fittings, drains, sinks, WCs, blinds or radiators that are difficult to access. The closer the spotlight nozzle is to the soiled area, the greater the cleaning efficiency will be. Slide the spotlight nozzle onto the steam gun.

Round brush (small/large): Used for cleaning stubborn dirt. Stubborn dirt can be removed more easily by brushing. ATTENTION: The brush may scratch sensitive surfaces. Fit the round brush to the spotlight nozzle.

Power nozzle: Used for cleaning stubborn dirt, blowing down corners, joins etc. Install the power nozzle onto the spotlight nozzle according to the round brush.

Manual nozzle: Used for cleaning small areas that can be washed down, shower cubicles and mirrors. Push the manual nozzle onto the steam gun and pull the cover over the manual nozzle.

Floor nozzle: Used for cleaning washable wall and floor coverings e.g. stone floors, tiles and PVC floors. ATTENTION: Heat and moisture can lead to damage. Check the heat resistance and steam effect on an inconspicuous area prior to use.

1. Connect the extension tubes with the steam gun.

2. Push the floor nozzle onto the extension tube.

3. Fasten the floor cleaning cloth to the floor nozzle by placing it on the floor with hook and loop fastener strips pointing upwards, then place the floor nozzle onto it with slight pressure.

To remove the cloth, place one foot on the bottom corner of the cloth and lift the floor nozzle up.

Note: Initially, the cloth’s hook and loop fastener strip is very strong. After being used several times and washed, it is easier to remove.

Parking the floor nozzle: Hang the floor nozzle in the park bracket during breaks in work.

The carpet glider is used for freshening up carpets.

ATTENTION: Beware of damaging the carpet glider and carpet. Contamination on the carpet glider, as well as heat and moisture penetration, can result in the carpet being damaged. Prior to the application, check the heat resistance and impact of steam on the carpet at an insignificant spot. Prior to using the carpet glider, make sure that the carpet has been vacuumed and that stains have been removed. Only use the carpet glider with a floor cleaning cloth on the floor nozzle. Steam clean with a weak steam stage. Do not direct the steam continuously onto one spot (maximum 5 seconds).

Fastening the carpet glider to the floor nozzle:

1. Fasten the floor cleaning cloth to the floor nozzle.

2. Using a little force, allow the floor nozzle to slide into the carpet glider and engage there.

3. Start cleaning the carpet.

Removing the carpet glider from the floor nozzle:

CAUTION: Beware of burns to your feet. The carpet glider can heat up during the steaming process. Do not operate or remove the carpet glider bare-footed or using open sandals. Only operate or remove the carpet glider using suitable footwear.

1. Press the strap on the carpet glider downwards using your toecap.

2. Lift the floor nozzle upwards.

Note: We recommend using the KÄRCHER ironing board with active steam suctioning. The iron plate must be hot to prevent steam from condensing on the sole plate and dripping onto the ironing laundry. Do not turn on the steam stage for the VapoHydro function when the steam pressure iron is plugged in, since otherwise the ironing laundry will get wet.

Recommended steam stages:

Initial Startup:

1. Ensure that tap water or a mixture of tap water and no more than 50% distilled water is in the steam boiler of the steam cleaner.

2. Insert the steam plug of the iron into the unit plug until it clicks into place.

3. Put the steam cleaner into operation.

4. Wait until the steam cleaner is ready for use.

5. The iron is ready for use as soon as the indicator light (orange) has gone out.

6. The warning light comes on during use when the iron is reheating. The application must not be interrupted during reheating.

Steam ironing:

ATTENTION: Failure to observe the ironing information in the garment may result in damage. Observe the ironing information in the garment.

Note: With the fixed, optimal temperature setting, all ironable textiles can be ironed without additional temperature setting. Smooth delicate fabrics and imprints on the back with steam without direct contact with the iron. The iron can be held vertically for steaming curtains, dresses, etc.

1. As soon as the heating indicator light (orange) of the iron goes out, ironing can be started.

2. Press the steam switch on the handle below. Steam emits as long as the switch is pressed.

3. Before ironing and after pauses, direct the blast of steam onto a cloth until the steam flows evenly.

Dry ironing:

ATTENTION: Water shortage in the steam boiler leads to damage to the device. Make sure that there is water in the steam boiler. Delicate fabrics and prints should not be dry ironed. Wait until the heating indicator light (orange) of the iron goes out. The iron is ready for ironing.

Note: Descaling the steam boiler is not required if commercially available distilled water is used. Since the lime clogs the appliance, we recommend descaling the appliance based on the number of times the water reservoir is filled as specified in the table (TF=tank fillings).

Note: Your water board or municipal utilities authority can provide information on hardness of tap water.

ATTENTION: Damaged surfaces. The descaler may corrode sensitive surfaces. Fill and empty the appliance carefully.

1. Switching off the device, see chapter Switching on the device.

2. Allow the device to cool down.

3. Drain the water reservoir.

4. Remove the accessory/accessories from the accessory holders.

5. Open the cap of the accessory compartment.

6. Remove the accessory from the accessory compartment.

7. Open the maintenance lock. To do this place the open end of an extension tube on the maintenance lock, insert this into the guide so it engages and open it.

8. Drain the water completely out of the steam boiler.

ATTENTION: Appliance damage due to descaler. An unsuitable descaler or incorrect dosing of the descaler may damage the appliance. Only use KÄRCHER descaler. Use 1 dosing unit of the descaler for 0.5 l water.

9. Apply descaler solution to the descaler according to the details.

10. Fill the descaler solution into the steam boiler. Do not seal the steam boiler.

11. Allow the descaler solution to take effect for approx. 8 hours.

12. Drain descaler solution completely out of the steam boiler.

13. Repeat the descaling process if necessary.

14. Rinse the steam boiler 2-3 times with cold water in order to drain all the descaler solution residue.

15. Drain the water completely out of the steam boiler.

16. Dry the mounting for the grid connection cable.

17. Close the maintenance lock with an extension tube.

Note: The micro fibre cloths are not suitable for dryer.

Note: When washing the cloths, observe the instructions on the washing tag. Do not use any liquid softeners as this will affect the ability of the cloths to pick up dirt.

1. Wash the floor cleaning cloths and covers at a max. temperature of 60 °C in the washing machine.

This indicates there is no water in the tank. Fill the water reservoir up to the “MAX” marking.

This means there is no water in the steam boiler and the pump’s overheat protection has triggered, or the water tank is not inserted correctly or is calcified.

To resolve the overheat protection issue:

1. Switch the device off.

2. Fill the water reservoir.

3. Switch on the device.

To resolve the water tank issue:

1. Remove the water reservoir.

2. Rinse the water reservoir.

3. Insert the water reservoir and press downwards until it locks into place.

The steam lever is locked with the child lock. Set the child lock (selector switch for steam volume) to the front. The steam lever will be released.

A long heating-up time indicates that the steam boiler is scaled. You should descale the steam boiler.

A high water output can be caused by two issues:

1. The steam boiler is scaled. You should descale the steam boiler.

2. The VapoHydro steam stage is set. Turn the selector switch to the steam setting selection range.

If your steam pressure iron “spits” water, you should rinse or descale the steam boiler of the steam cleaner.

During longer ironing breaks, steam can condense in the steam line. After pauses in the ironing process, direct the blast of steam onto a cloth until the steam flows evenly.