KARCHER LVL 1-1 BP (01) PDF Document

The KARCHER LVL 1-1 BP is a universal vacuum cleaner intended for dry cleaning of floor and wall surfaces. It is suitable for commercial use in locations such as hotels, schools, hospitals, factories, shops, offices, and rental companies. It should only be used and stored indoors.

WARNING: Do not use the device for vacuuming up dusts that are harmful to health.

In addition to the main operating instructions, you should read the operating instructions and safety instructions that come with the battery pack and the charger. This device can be operated with all 18 V / 36 V Kärcher Battery Power and Battery Power+ battery packs.

To install accessories on your KARCHER LVL 1-1 BP, follow these steps:

1. Install the floor nozzle tube and floor nozzle head together in the direction shown in the illustration.

2. Push the floor nozzle onto the end of the suction tube until it is tight, and push the other end of the suction tube onto the main body.

3. To remove, pull the floor nozzle or the suction tube in the opposite direction of installation.

4. Install the crevice nozzle holder on the suction tube in the direction shown in the illustration. The crevice nozzle can be stored in the holder.

5. Push an accessory, such as the crevice nozzle, onto the suction fitting of the dust container or suction pipe until it is tight.

The floor nozzle is ideal for hard floors and carpet. The crevice nozzle is for edges, joints, heaters, and areas that are difficult to reach.

Inserting the battery pack:

Slide the battery pack into the battery holder and lock it in place.

Charging the battery pack:

Please read the operating instructions of the charger and battery pack manufacturer, especially the chapters on safety instructions.

Note: The battery pack is partially charged on delivery. Charge before use and when necessary. The battery pack can only be charged when it is removed.

1. Press the unlocking button and remove the battery pack.

2. Charge the battery pack according to the operating instructions of the charger manufacturer and the battery pack manufacturer.

Switching the device on/off:

1. Press the on/off button to start the device.

2. Press the on/off button again to stop the device.

Mode adjustment:

The KARCHER LVL 1-1 BP has 3-mode options for power and run time management. You can change the suction power in three steps by pressing the mode button. Each press on this button repeats the Eco / Standard / Power mode in a cycle.

Mode memory:

The selected mode before the last shutdown remains stored and is reactivated when the device is switched on again.

The LED on the KARCHER LVL 1-1 BP shows information on the power level and error messages.

Indicators	LED status	Mode
	1st LED light up blue	ECO Mode*: Minimum suction power
	1st LED light up blue 2nd LED light up green	Standard Mode: Standard suction power
	1st LED light up blue 2nd and 3rd LED light up green	Power Mode: Maximum suction power

*Eco mode: The device works with reduced suction performance. The battery run time is extended.

Error message

Indicators	LED status	Information
	1st LED flashes orange	Blockage / filtration missing

To ensure optimum suction performance, empty the dust container before it exceeds the “Max” line.

1. Switch off the device. Press the On/Off switch again to turn the device off.

2. Pointing the floor nozzle downwards, pull the dust container apart from the main body by holding the dust container firmly and pressing the release buttons on both sides.

3. Empty the dust container.

4. Reinsert the dust container.

The device may only be stored indoors. Be aware of the weight of the device during storage.

On the wall:

Install the wall mount on a sturdy wall, beam, or column to ensure a secure attachment. Before hanging the device, always double-check that the wall mount is firmly and securely attached.

1. Choose the desired location on the wall and mark the positions for the two mounting holes. Ensure the distance between the holes is 60 mm. The suggested height for the mounting holes is 700 mm.

2. Place the wall mount at the desired position and mark the positions for the two mounting holes.

3. Drill two holes at the marked positions.

4. Insert the dowels into the drilled holes.

5. Position the wall mount onto the installation location and securely fasten it using screws.

6. Press the unlocking button and remove the battery pack to prevent discharge.

7. Push the device into the bracket and secure it against unauthorized use.

On the Flexomate trolley:

The LVS vacuum cleaners can be stored on the Flexomate trolley, enabling easy transportation. The vacuum cleaner can be quickly detached and is ready for use whenever needed.

1. Insert the FlexoLink connection into the Flexomate adapter.

2. Securely rotate the Flexomate adapter to lock it onto the Flexomate trolley. After rotating, ensure the surface marked with “UP” is facing upward.

3. Push the device into the Flexomate adapter.

Cleaning the cyclone:

1. Press the filtration release button with one hand, and pull the filtration system out with the other hand. Clean the adhered dust off the mesh metal filter.

Cleaning / Replacing the filter:

1. Pull out the filtration system.

2. Take out the HEPA filter.

3. Clean the filter element by gently knocking it or replace it if necessary.

4. Take the sponge filter out.

5. Rinse the sponge filter by running water and dry it completely, or replace the sponge filter.

6. Install the sponge filter and HEPA into the filtration system.

7. With the arrow facing upward, and following the direction of the arrow, push the filtration system into the main body until it audibly clicks into place.

ATTENTION: Carefully clean the filters by gently knocking the dirt out. Do not expose the filter area to any mechanical loads and replace the filters if damaged. Do not operate the device without the complete filter elements.

If your KARCHER LVL 1-1 BP is not working, check the following:

Battery is empty: Charge the rechargeable battery.

Battery is not inserted correctly: Push the battery into the mount until it locks into place.

Battery is defective: Replace the battery.

If the LED strip flashes orange and the device does not start up, it means the filtration system is not installed properly. To fix this:

1. Check whether the HEPA filter and filtration are in the right position.

2. Install the HEPA filter into the filtration system.

3. With the arrow facing upward, following the direction of the arrow, push the filtration system into the main body until it audibly clicks into place.

If you experience a blockage or poor performance, check the following:

1. Floor nozzle blockage:

Disassemble the floor nozzle and clean the blockage.

2. Suction tube blockage:

Disassemble the suction tube and remove the blockage.

3. The dust container is full:

Empty the dust container.

4. The filters are soiled:

Clean the cyclone, HEPA, and sponge filter by referring to the section “Cleaning the filtration system.”

If you have an unsatisfactory vacuuming result:

1. Remove blockages from the brush head and suction tube.

2. Clean the cyclone or replace the motor protection filter or HEPA filter.