HUSQVARNA 395 XPG (01) PDF DOCUMENT

A chainsaw is a dangerous tool if used carelessly or incorrectly and can cause serious injury or death. It is very important that you read and understand the contents of this operator’s manual.

Under no circumstances may the design of the HUSQVARNA 395 XPG product be modified without the permission of the manufacturer. Do not use a product that appears to have been modified by others and only use accessories recommended for this product. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others.

A used muffler/spark arrester and spark arrester mounting face may contain deposits of combustion particles that may be carcinogenic. Avoid being exposed to these compounds when handling the muffler and/or spark arrester.

Long term inhalation of the engine’s exhaust fumes, chain oil mist and sawdust can represent a health risk.

This HUSQVARNA 395 XPG product produces an electromagnetic field during operation. This field may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, it is recommended for persons with medical implants to consult their physician and the medical implant manufacturer before operating this product.

The information in this operator’s manual is never a substitute for professional skills and experience. If you get into a situation where you feel unsafe, stop and seek expert advice. Do not attempt any task that you feel unsure of!

Before using the HUSQVARNA 395 XPG chainsaw you must understand the effects of kickback and how to avoid them.

Never use a HUSQVARNA 395 XPG product that is faulty.

Never use a HUSQVARNA 395 XPG product with visible damage to the spark plug cap and ignition cable. A risk of sparking arises, which can cause a fire.

Never use the HUSQVARNA 395 XPG product if you are fatigued, while under the influence of alcohol or drugs, medication or anything that could affect your vision, alertness, coordination or judgment.

Do not use the HUSQVARNA 395 XPG product in bad weather such as dense fog, heavy rain, strong wind, intense cold, etcetera. Working in bad weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etcetera.

Never start a HUSQVARNA 395 XPG product unless the guide bar, saw chain and all covers are fitted correctly. Without a bar and saw chain attached to the product the clutch can come loose and cause serious injury.

Never start the HUSQVARNA 395 XPG product indoors. Exhaust fumes can be dangerous if inhaled.

The exhaust fumes from the HUSQVARNA 395 XPG engine are hot and can contain sparks, which can start a fire. Never start the product near flammable material!

Observe your surroundings and make sure that there is no risk of people or animals coming in contact with or affect your control of the HUSQVARNA 395 XPG product.

Never allow children to use or be in the vicinity of the HUSQVARNA 395 XPG product. As the product is equipped with a spring-loaded start/stop switch and can be started by low speed and force on the starter handle, even small children under some circumstances can produce the force necessary to start the product. This can mean a risk of serious personal injury. Therefore remove the spark plug cap when the product is not under close supervision.

You must have a steady stance in order to have full control of the HUSQVARNA 395 XPG product. Never work standing on a ladder, in a tree or where you do not have a firm ground to stand on.

Working in a tree requires the use of special cutting and working techniques which must be observed in order to reduce the increased risk of personal injury. Never work in a tree unless you have received specific, professional training for such work, including training in the use of safety and other climbing equipment, such as harnesses, ropes, belts, climbing irons, snap hooks, carabiners, etcetera.

Never attempt to catch falling sections. Never cut in the tree when you are only secured with one rope. Always use two secured ropes.

Lack of concentration can lead to kickback if the kickback zone of the bar accidentally touches a branch, nearby tree or some other object.

Never use the HUSQVARNA 395 XPG product by holding it with one hand. This product is not safely controlled with one hand.

Always hold the HUSQVARNA 395 XPG product with both hands. The right hand should be on the rear handle, and the left hand on the front handle. All people, whether right or left handed, should use this grip. Use a firm grip with thumbs and fingers encircling the handles. This grip minimizes the risk of kickback and lets you keep the product under control. Do not let go of the handles!

Never use the HUSQVARNA 395 XPG product above shoulder height.

Do not use the HUSQVARNA 395 XPG product in a situation where you cannot call for help in case of an accident.

Before moving your HUSQVARNA 395 XPG product, switch off the engine and lock the saw chain using the chain brake. Carry the product with the guide bar and saw chain pointing backwards. Fit a transportation guard to the guide bar before transporting the product or carrying it for any distance.

When you put the HUSQVARNA 395 XPG product on the ground, lock the saw chain using the chain brake and ensure you have a constant view of the product. Switch the engine off before leaving your product for any length of time.

Sometimes chips get stuck in the clutch cover causing the saw chain to jam. Always stop the engine before cleaning.

Running an engine in a confined or badly ventilated area can result in death due to carbon monoxide poisoning.

Use the chain brake as a parking brake when you start the HUSQVARNA 395 XPG product and when you move short distances. Always carry the product in the front handle. This decreases the risk that you or a person near you get hit by the saw chain.

It is not possible to cover every conceivable situation you can face when using this HUSQVARNA 395 XPG product. Always exercise care and use your common sense. Avoid all situations which you consider to be beyond your capability. If you still feel uncertain about operating procedures after reading these instructions, you should consult an expert before continuing. Attend a training course in chainsaw usage if possible. Your dealer, forestry school or your library can provide information about which training materials and courses are available.

When using this HUSQVARNA 395 XPG product, a fire extinguisher should be available.

Keep handles dry, clean and free from oil.

Beware of carbon monoxide poisoning. Operate the HUSQVARNA 395 XPG product in a well ventilated area only.

Do not attempt a pruning or limbing operation in a standing tree unless specifically trained to do so.

Most chainsaw accidents occur when the saw chain touches the operator. You must use approved personal protective equipment during operation. Personal protective equipment does not give you full protection from injuries but it decreases the degree of injury if an accident occurs.

Your clothing must be close-fitting but not limit your movements. Regularly do a check of the condition of the personal protective equipment.

Use an approved protective helmet.

Use approved hearing protection. Long-term exposure to noise can result in permanent damage to the hearing.

Use approved protective glasses or a face visor to decrease the risk of injury from thrown objects. The HUSQVARNA 395 XPG product can throw objects, such as wood chips, small pieces of wood and more, at large force. This can result in serious injury, especially to the eyes.

Use gloves with saw protection.

Use pants with saw protection.

Use boots with saw protection, steel toe-cap and non-slip sole.

Always have a first-aid kit with you.

Risk of sparks. Keep fire extinguishing tools and a shovel near to prevent forest fires.

Do not use a HUSQVARNA 395 XPG product with safety devices that are damaged or do not operate correctly.

Do a check of the safety devices regularly.

If the safety devices are damaged or do not operate correctly, speak to your Husqvarna servicing dealer.

Your HUSQVARNA 395 XPG product has a chain brake that stops the saw chain if you get a kickback. The chain brake decreases the risk of accidents, but only you can prevent them.

The chain brake engages manually by your left hand or automatically by the inertia release mechanism. Push the front hand guard forward to engage the chain brake manually.

Pull the front hand guard rearward to disengage the chain brake.

The throttle trigger lockout prevents accidental operation of the throttle trigger. If you put your hand around the handle and press the throttle trigger lockout, it releases the throttle trigger. If you release the handle, the throttle trigger and the throttle trigger lockout move back to their initial positions. This function locks the throttle trigger at idle speed.

The chain catcher catches the saw chain if it breaks or comes loose. Correct saw chain tension and correctly applied maintenance on the saw chain and guide bar, decrease the risk of accidents.

The right hand guard is a protection for your hand on the rear handle. The right hand guard gives you protection if the saw chain breaks or derails. The right hand guard also gives you protection from branches or twigs.

The vibration damping system decreases vibration in the handles. Vibration damping units operate as a separation between the product body and the handle unit.

Use the start/stop switch to stop the engine.

The muffler becomes very hot during/after operation and at idle speed. There is a risk of fire, especially when you operate the HUSQVARNA 395 XPG product near flammable materials and/or fumes.

Do not operate a HUSQVARNA 395 XPG product without a muffler or with a defective muffler. A defective muffler can increase the noise level and the risk of fire. Keep fire extinguishing tools near. Do not use a product without, or with a broken, spark arrestor mesh if you must have a spark arrester mesh in your area.

The muffler keeps the noise levels to a minimum and points the exhaust fumes away from the operator. In areas with hot, dry weather there is a high risk of fire.

Make sure there is plenty of ventilation when refuelling or mixing fuel (petrol and two-stroke oil).

Fuel and fuel vapour are highly flammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation.

Take care when handling fuel and chain oil. Be aware of the risks of fire, explosion and those associated with inhalation.

Do not smoke and do not place any hot objects in the vicinity of fuel.

Always stop the engine and let it cool for a few minutes before refuelling. Never refuel the machine while the engine is running.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the HUSQVARNA 395 XPG product at least 3 m (10 ft) away from the refuelling area and fuel source before starting.

If you have spilled fuel or chain oil on the HUSQVARNA 395 XPG product, wipe off the spillage and allow remaining fuel to evaporate.

If you have spilled fuel on yourself or on your clothes, change your clothes and wash any part of your body that has come in contact with fuel. Use soap and water.

If the HUSQVARNA 395 XPG product leaks fuel, regularly do a check for leaks from the fuel tank, fuel cap and fuel lines.

Do only the maintenance and servicing given in this operator’s manual. Let professional servicing personnel do all other servicing and repairs.

Regularly do the safety checks, maintenance and service instructions given in this manual. Regular maintenance increases the life of the HUSQVARNA 395 XPG product and decreases the risk of accidents.

If the safety checks in this operator’s manual are not approved after you do maintenance, speak to your Husqvarna servicing dealer. They guarantee that there are professional repairs and servicing available for your HUSQVARNA 395 XPG product.

Only use approved guide bar/saw chain combinations and filing equipment.

Use protective gloves when you use or do maintenance on the saw chain. A saw chain that does not move can also cause injuries.

Keep the cutting teeth correctly sharpened. Obey the instructions and use the recommended file gauge. A saw chain that is damaged or incorrectly sharpened increases the risk of accidents.

Keep the correct depth gauge setting. Obey the instructions and use the recommended depth gauge setting. Too large depth gauge setting increases the risk of kickback.

Make sure that the saw chain has the correct tension. If the saw chain is not tight against the guide bar, the saw chain can derail. An incorrect saw chain tension increases wear on the guide bar, saw chain and chain drive sprocket.

Do maintenance on the cutting equipment regularly and keep it correctly lubricated. If the saw chain is not correctly lubricated, the risk of wear on the guide bar, saw chain and chain drive sprocket increases.

1. Move the front hand guard rearward to disengage the chain brake.

2. Remove the bar nuts, clutch cover and transportation guard.

3. Assemble the guide bar onto the bar bolts. Move the guide bar to its most rear position.

4. Install the saw chain correctly around the drive sprocket and put it in the groove on the guide bar.

5. Make sure that the edges of the cutters point forward on the top edge of the guide bar.

6. Align the hole in the guide bar with the chain adjuster pin and install the clutch cover.

7. Tighten the bar nuts finger tight.

8. Tighten the saw chain.

9. Tighten the bar nuts.

If the clutch cover is not easy to remove, tighten the bar nut, engage the chain brake and release. A click is heard if it is released correctly.

Always use protective gloves when you assemble the saw chain on the HUSQVARNA 395 XPG chainsaw.

Some models of the HUSQVARNA 395 XPG chainsaw have only 1 bar nut.

1. Make sure that the chain brake operates correctly and that it is not damaged.

2. Make sure that the right hand guard is not damaged.

3. Make sure that the throttle lockout operates correctly and that it is not damaged.

4. Make sure that the start/stop switch operates correctly and that it is not damaged.

5. Make sure that there is no oil on the handles.

6. Make sure that the vibration damping system operates correctly and that it is not damaged.

7. Make sure that the muffler is correctly attached and that it is not damaged.

8. Make sure that all parts of the HUSQVARNA 395 XPG product are correctly attached and not damaged or missing.

9. Make sure that the chain catcher is correctly attached.

10. Do a check of the saw chain tension.

Incorrect type of fuel can result in engine damage. Use a mixture of gasoline and two-stroke oil.

Use Husqvarna premixed alkylate fuel for best performance and extension of the engine life. This fuel contains less harmful chemicals compared to regular fuel, which decreases harmful exhaust fumes. The quantity of remains after combustion is lower with this fuel, which keeps the components of the engine more clean.

Use good quality unleaded gasoline with a maximum of 10% ethanol contents.

Do not use gasoline with an octane grade less than 90 RON/87 AKI. Use of a lower octane grade can cause engine knocking, which causes engine damages.

For best results and performance use Husqvarna two-stroke oil.

If Husqvarna two-stroke oil is not available, use a two-stroke oil of good quality for air-cooled engines.

Do not use two-stroke oil for water-cooled outboard engines, also referred to as outboard oil. Do not use oil for four-stroke engines.

Small errors can influence the ratio of the mixture drastically when you mix small quantities of fuel. Measure the quantity of oil carefully and make sure that you get the correct mixture.

1. Fill half the quantity of gasoline in a clean container for fuel.

2. Add the full quantity of oil.

3. Shake the fuel mixture.

4. Add the remaining quantity of gasoline to the container.

5. Carefully shake the fuel mixture.

Do not mix fuel for more than 1 month at a time.

1. Stop the engine and let it become cool.

2. Clean the area around the fuel tank cap.

3. Shake the container and make sure that the fuel is fully mixed.

4. Remove the fuel tank cap slowly to release the pressure.

5. Fill the fuel tank.

6. Tighten the fuel tank cap carefully.

7. Clean fuel spillage on and around the product.

8. Move the product 3 m/10 ft or more away from the refueling area and fuel source before you start the engine.

Make sure there is not too much fuel in the fuel tank. The fuel expands when it becomes hot.

During the first 10 hours of operation, do not apply full throttle without load for extended periods.

Do not use waste oil, which can cause injury to you and the environment. Waste oil also causes damage to the oil pump, the guide bar and the saw chain.

The saw chain can break if the lubrication of the cutting equipment is not sufficient. Risk of serious injury or death to the operator.

This HUSQVARNA 395 XPG product has a function that lets the fuel run out before the chain oil. Use the correct chain oil for this function to operate correctly.

Use Husqvarna chain oil for maximum saw chain life and to prevent negative effects on the environment. If Husqvarna chain oil is not available, it is recommended to use a standard chain oil.

Use a chain oil with good adherence to the saw chain.

Use a chain oil with correct viscosity range that agrees with the air temperature.

If the oil is too thin, it runs out before the fuel. In temperatures below 0°C/32°F some chain oils become too thick, which can cause damage to the oil pump components.

Use the recommended cutting equipment.

A kickback can cause serious injury or death to the operator or others. To decrease the risk you must know the causes of kickback and how to prevent them.

A kickback occurs when the kickback zone of the guide bar touches an object. A kickback can occur suddenly and with large force, which throws the HUSQVARNA 395 XPG product in the direction of the operator.

Kickback always occurs in the cutting plane of the guide bar. Usually, the HUSQVARNA 395 XPG product is thrown against the operator but can also move in a different direction. It is how you use the product when the kickback occurs that causes the direction of the movement.

A smaller bar tip radius decreases the force of the kickback.

Use a low kickback saw chain to decrease the effects of kickback. Do not let the kickback zone touch an object.

No saw chain fully prevents kickback. Always obey the instructions.

No. It is necessary to use some force to push the front hand guard forward. If you do not use the force necessary, the chain brake will not be engaged. You must also hold the handles of the HUSQVARNA 395 XPG product stable with two hands during work. If a kickback occurs, it is possible that the chain brake does not stop the saw chain before it touches you. There are also some positions in which your hand can not touch the front hand guard to engage the chain brake.

No. First, the chain brake must operate correctly. It is recommended to do a check of the chain brake each time before you use the product. Second, the force of the kickback must be large to engage the chain brake. If the chain brake is too sensitive, it can engage during rough operation.

No. The chain brake must operate correctly to give protection. The chain brake must also be engaged during a kickback to stop the saw chain. If you are near the guide bar, it is possible that the chain brake does not have time to stop the saw chain before it hits you.

Only you and the correct working technique can prevent kickbacks.

The chain brake must be engaged when the HUSQVARNA 395 XPG product is started to decrease the risk of injury.

1. Move the front hand guard forward to engage the chain brake.

2. Set the start/stop switch to on.

3. Pull the choke control out to set the choke control in choke position.

4. Push the decompression valve.

1. Move the front hand guard forward to engage the chain brake.

2. Set the start/stop switch to on.

3. Pull out and push in the choke control.

4. Push the decompression valve.

You must keep your feet in a stable position when you start the HUSQVARNA 395 XPG product.

If the saw chain rotates at idle speed, speak to your servicing dealer and do not use the HUSQVARNA 395 XPG product.

1. Put the product on the ground.

2. Put your left hand on the front handle.

3. Put your right foot into the footgrip on the rear handle.

4. Pull the starter rope handle slowly with your right hand until you feel resistance.

5. Pull the starter rope handle quickly and with force.

6. If you start your product with a cold engine, pull the starter rope handle until the engine fires. Disengage the choke.

7. Pull the starter rope handle until the engine starts.

8. Quickly disengage the throttle trigger lockout to set the product to idle speed.

9. Move the front hand guard rearward to disengage the chain brake.

10. Use the product.

Do not twist the starter rope around your hand.

Do not pull the starter rope to full extension and do not let go of the starter rope handle. This can cause damage to the HUSQVARNA 395 XPG product.

You can identify when the engine fires through a “puff” sound.

To cut on the pull stroke is when you cut with the bottom of the guide bar. The saw chain pulls through the tree when you cut. In this position you have better control of the HUSQVARNA 395 XPG product and the position of the kickback zone.

To cut on the push stroke is when you cut with the top of the guide bar. The saw chain pushes the HUSQVARNA 395 XPG product in the direction of the operator.

If the saw chain is caught in the trunk, the HUSQVARNA 395 XPG product can be pushed at you. Hold the product tightly and make sure that the kickback zone of the guide bar does not touch the tree and causes a kickback.

Use full throttle when you cut and decrease to idle speed after each cut.

Engine damage can occur if the engine runs for too long at full throttle without load.

1. Put the trunk on a saw horse or runners.

2. Remove the cut pieces from the cutting area.

Do not cut trunks in a pile. That increases the risk of kickback and can result in serious injury or death.

Cut pieces in the cutting area increase the risk of kickback and that you cannot keep your balance.

1. Cut through the trunk on the pull stroke. Keep full throttle but be prepared for sudden accidents.

2. Cut approximately ⅔ through the trunk and then stop. Turn the trunk and cut from the opposite side.

Make sure that the saw chain does not touch the ground when you complete the kerf.

1. Cut on the push stroke approximately ⅓ through the trunk.

2. Cut through the trunk on the pull stroke until the two kerfs touch.

1. Cut on the pull stroke approximately ⅓ through the trunk.

2. Cut through the remaining part of the trunk on the push stroke to complete the cut.

Stop the engine if the saw chain gets caught in the trunk. Use a lever to open up the kerf and remove the product. Do not try to pull the product out by hand. This can result in injury when the product suddenly breaks free.

For thick branches, use the cutting technique.

There is a high accident risk when you use the limbing technique.

Cut limbs one by one. Be careful when you remove small limbs and do not cut bushes or many small limbs at the same time. Small limbs can get caught in the saw chain and prevent safe operation of the HUSQVARNA 395 XPG product.

Cut the limbs piece by piece if it is necessary.

1. Keep the guide bar on the right side of the trunk and keep the body of the HUSQVARNA 395 XPG product against the trunk.

2. Select the applicable cutting technique for the tension in the branch.

If you are not sure about how to cut the branch, speak to a professional chainsaw operator before you continue.

1. Keep the HUSQVARNA 395 XPG product on the trunk and let the guide bar move along the trunk.

2. Cut on the push stroke.

1. Select the applicable cutting technique for the tension in the branch.

You must have experience to fell a tree. If possible, engage in a training course in chainsaw operation.

1. Make sure that persons around you keep a safe distance at a minimum of 2 1/2 tree lengths.

2. Make sure that no person is in the risk zone before or during felling.

1. Examine in which direction it is necessary for the tree to fall. The goal is to fell it in a position where you can limb and cut the trunk easily. It is also important that you are stable on your feet and can move about safely.

2. Examine the natural fall direction of the tree. For example the tilt and bend of the tree, wind direction, the location of the branches and weight of snow.

3. Examine if there are obstacles, for example other trees, power lines, roads and/or buildings around.

4. Look for signs of damage and rot in the stem.

5. Make sure the tree has no damaged or dead branches that can break off and hit you during felling.

If it is dangerous or not possible to fell the tree in its natural direction, fell the tree in a different direction.

Rot in the stem can mean a risk that the tree falls before you complete the cutting.

Do not let the tree fall onto a different standing tree. It is dangerous to remove a caught tree and there is a high accident risk.

During critical felling operations, lift your hearing protection immediately when the sawing is complete. It is important that you hear sounds and warning signals.

Cut off all branches from your shoulder height and down.

1. Cut on the pull stroke from the top down. Make sure that the tree is between you and the HUSQVARNA 395 XPG product.

2. Remove undergrowth from the work area around the tree. Remove all cut off material from the work area.

3. Do a check of the area for obstacles such as stones, branches and holes. You must have a clear path of retreat when the tree starts to fall. Your path of retreat must be approximately 135 degrees away from the felling direction.

Husqvarna recommends you to make the directional cuts and then use the safe corner method when you fell a tree. The safe corner method helps you to make a correct felling hinge and control the felling direction.

Do not fell trees with a diameter that is more than two times larger than the guide bar length. For this, you must have special training.

The most important procedure during tree felling is to make the correct felling hinge. With a correct felling hinge, you control the felling direction and make sure that the felling procedure is safe.

The thickness of the felling hinge must be equal and a minimum of 10% of the tree diameter.

If the felling hinge is incorrect or too thin, you have no control of the felling direction.

1. Make the directional cuts ¼ of the diameter of the tree. Make a 45°-70° angle between the top directional cut and bottom directional cut.

a) Make the top directional cut. Align the felling direction mark of the HUSQVARNA 395 XPG product with the felling direction of the tree. Stay behind the product and keep the tree on your left side. Cut with a pull stroke.

b) Make the bottom directional cut. Make sure that the end of the bottom directional cut is at the same point as the end of the top directional cut.

2. Make sure that the bottom directional cut is horizontal and at a 90° angle to the felling direction.

Be careful when you cut with the guide bar tip. Start to cut with the lower section of the guide bar tip as you make a bore cut into the trunk.

1. Make a bore cut straight into the trunk to complete the felling hinge width.

2. Cut on the pull stroke until ⅓ of the trunk is left.

3. Pull the guide bar 5-10 cm/2-4 in rearward.

4. Cut through the remaining of the trunk to complete a safe corner that is 5-10 cm/2-4 in wide.

1. Make a bore cut straight into the trunk. The bore cut must extend 3/5 of the tree diameter.

2. Cut on the pull stroke through the remaining trunk.

3. Cut straight into the trunk from the other side of the tree to complete the felling hinge.

4. Cut on the push stroke, until ⅓ of the trunk is left, to complete the safe corner.

It is very dangerous to remove a trapped tree and there is a high accident risk. Keep out of the risk zone and do not try to fell a trapped tree.

The safest procedure is to use one of the following winches: Tractor-mounted, Portable.

1. Figure out which side of the tree or branch that is in tension.

2. Figure out where the point of maximum tension is.

3. Examine which is the safest procedure to release the tension.

4. Keep a position where the tree or branch can not hit you when the tension is released.

5. Make one or more cuts of sufficient depth necessary to decrease the tension. Cut at or near the point of maximum tension. Make the tree or branch break at the point of maximum tension.

6. If you must cut across tree/branch, make 2 to 3 cuts, 1 in. apart and with a depth of 2 in.

In some situations the only safe procedure is to use a winch and not your HUSQVARNA 395 XPG product.

Do not cut straight through a tree or branch that is in tension.

Be very careful when you cut a tree that is in tension. There is a risk that the tree moves quickly before or after you cut it. Serious injury can occur if you are in an incorrect position or if you cut incorrectly.

Continue to cut more into the tree until the tree/branch bends and the tension is released. Then, cut the tree/branch from the opposite side of the bend, after the tension is released.

Snow and cold weather can cause operation problems. There is a risk of too low engine temperature or ice on the air filter and the carburetor.

1. Remove the cylinder cover.

2. Remove the partition wall.

3. Use a knife to make a hole in the cylinder cover as shown in the illustration.

4. Assemble the winter plug.

For temperatures below 0°C/32°F, move the winter plug from position 1 to position 2.

When the winter plug is in the air nozzle for AirInjection™, you must clean the air filter daily.

For temperatures below -5°C/23°F or in conditions with snow, a winter cover is available. Assemble the winter cover on the starter housing. The winter cover decreases the flow of cool air and keeps snow away from the carburetor space.

Remove the winter cover if the temperature increases above -5°C/23°F. Put the winter plug in position 1 if the temperature increases above 0°C/32°F. Otherwise, there is a risk of too high engine temperature and damage to the engine.

The HUSQVARNA 395 XPG product has heated front and rear handles. The electrical heating coils are powered by a generator.

Push the switch in the direction of the arrow to engage the function. Push the switch in the opposite direction to disengage the function.

Adjustment of the carburetor heating is done electrically through a thermostat. This keeps the correct carburetor temperature and prevents ice in the carburetor.

1. Use a brush to remove wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can decrease the function of the brake.

2. Do a check of the brake band. The brake band must be at a minimum of 0.6 mm/0.024 in thick at its thinnest point.

1. Make sure that the front hand guard does not have damages such as cracks.

2. Make sure that the front hand guard moves freely and that it is attached safely to the clutch cover.

3. Hold the HUSQVARNA 395 XPG product with 2 hands above a stump or other stable surface.

4. Let go of the front handle and let the guide bar tip fall against the stump.

5. Make sure that the chain brake engages as the guide bar tip hits the stump.

The engine must be off.

1. Start the HUSQVARNA 395 XPG product.

2. Hold the product tightly.

3. Apply full throttle and tilt your left wrist against the front hand guard to engage the chain brake. The saw chain must stop immediately.

Make sure that the saw chain does not touch the ground or other objects.

Do not let go of the front handle.

1. Make sure that the throttle trigger and throttle trigger lockout move freely and that the return spring works correctly.

2. Press down the throttle trigger lockout and make sure that it goes back to its initial position when you release it.

3. Make sure that the throttle trigger is locked at the idle position when the throttle trigger lockout is released.

4. Start the HUSQVARNA 395 XPG product and apply full throttle.

5. Release the throttle trigger and make sure that the saw chain stops and stays stationary.

If the saw chain rotates when the throttle trigger is in the idle position, speak to your servicing dealer.

1. Make sure that there is no damage on the chain catcher.

2. Make sure that the chain catcher is stable and attached to the body of the HUSQVARNA 395 XPG product.

Make sure that the right hand guard does not have damages such as cracks.

1. Make sure that there are no cracks or deformation on the vibration damping units.

2. Make sure that the vibration damping units are correctly attached to the engine unit and handle unit.

1. Start the engine.

2. Push the start/stop switch to the STOP position. The engine must stop.

Do not use a HUSQVARNA 395 XPG product if the spark arrestor mesh on the muffler is missing or defective.

1. Examine the muffler for damages and defects.

2. Make sure that the muffler is correctly attached to the HUSQVARNA 395 XPG product.

3. If your HUSQVARNA 395 XPG product has a special spark arrestor mesh, clean the spark arrester mesh weekly.

4. Replace a damaged spark arrestor mesh.

If the spark arrestor mesh is blocked the HUSQVARNA 395 XPG product becomes too hot and this causes damage to the cylinder and piston.

Because of environmental and emissions laws, your HUSQVARNA 395 XPG product has adjustment limitations on the carburetor adjuster screws. This decreases the harmful exhaust fumes from your product. You can only turn the adjustment screws maximum ½ turn.

Do not operate the HUSQVARNA 395 XPG product at too high speed during the first 10 hours of operation.

Turn the low speed needle clockwise until stop.

If the HUSQVARNA 395 XPG product has a bad acceleration capacity or if the idle speed is not correct, turn the low speed needle counterclockwise. Turn the low speed needle until the acceleration capacity and idle speed is correct.

1. Start the HUSQVARNA 395 XPG product.

2. Turn the idle speed screw clockwise until the saw chain starts to rotate.

3. Turn the idle speed screw counterclockwise until the saw chain stops.

The idle speed is correctly adjusted when the engine runs correctly in all positions. The idle speed must also be safely below the speed at which the saw chain starts to rotate.

Turn the high speed needle to make adjustments.

Do not turn the high speed needle screw across the adjustment limitation stop. This can cause damage to the piston and the cylinder.

Make sure that the HUSQVARNA 395 XPG product has the correct acceleration capacity.

Make sure that the HUSQVARNA 395 XPG product 4-cycles a little at full throttle.

Make sure that the saw chain does not rotate at idle speed.

If the HUSQVARNA 395 XPG product is not easy to start or has less acceleration capacity, adjust the low and high speed needles.

Incorrect adjustments can cause damage to the engine.

1. Loosen the screws to the starter housing.

2. Remove the starter housing.

3. Pull out the starter rope approximately 30 cm/12 in and put it in the notch on the pulley.

4. Let the pulley rotate slowly rearward to release the recoil spring.

5. Remove the center screw and remove the pulley.

6. Remove the used starter rope from the handle and the pulley.

7. Attach a new starter rope to the pulley. Wind the starter rope approximately 3 turns around the pulley.

8. Connect the pulley to the recoil spring. The end of the recoil spring must engage in the pulley.

9. Assemble the pulley and center screw.

10. Pull the starter rope through the hole in the starter housing and the starter rope handle.

11. Make a tight knot at the end of the starter rope.

You must be careful when you replace the return spring or the starter rope. The recoil spring is in tension when it is wound up in the starter housing. If you are not careful, it can eject and cause injuries. Use protective glasses and protective gloves.

1. Put the starter rope into the notch in the pulley.

2. Turn the starter pulley approximately 2 turns clockwise.

3. Pull the starter rope handle and pull out the starter rope fully.

4. Put your thumb on the pulley.

5. Move your thumb and release the starter rope.

6. Make sure that you can turn the pulley ½ turn after the starter rope is fully extended.

1. Pull out the starter rope and put the starter in position against the crankcase.

2. Slowly release the starter rope until the pulley engages with the pawls.

3. Tighten the screws that hold the starter.

Clean the air filter regularly from dirt and dust. This prevents carburetor malfunctions, starting problems, loss of engine power, wear to engine parts and more fuel consumption than usual.

1. Remove the cylinder cover and the air filter.

2. Use a brush or shake the air filter clean. Use detergent and water to clean it fully.

3. Attach the air filter and make sure that the air filter seals tightly against the filter holder.

An air filter that is used for a long time can not be fully cleaned. Replace the air filter regularly and always replace a defective air filter.

Because of different work conditions, weather or season, your HUSQVARNA 395 XPG product can be used with different types of air filter.

Use the recommended spark plug. An incorrect spark plug can cause damage to the HUSQVARNA 395 XPG product.

1. If the HUSQVARNA 395 XPG product is not easy to start or to operate or if the product operates incorrectly at idle speed, examine the spark plug for unwanted materials. To decrease the risk of unwanted material on the spark plug electrodes, do these steps:

a) make sure that the idle speed is correctly adjusted.

b) make sure that the fuel mixture is correct.

c) make sure that the air filter is clean.

2. Clean the spark plug if it is dirty.

3. Make sure that the electrode gap is correct.

4. Replace the spark plug monthly or more frequently if necessary.

Replace a worn or damaged guide bar or saw chain with the guide bar and saw chain combination recommended by Husqvarna. This is necessary to keep the safety functions of the HUSQVARNA 395 XPG product.

Guide bar length, in/cm. Information about the guide bar length can usually be found on the rear end of the guide bar.

Do not use a blunt saw chain. If the saw chain is blunt, you must apply more pressure to push the guide bar through the wood. If the saw chain is very blunt, there will be no wood chips but sawdust.

A sharp saw chain eats through the wood and the wood chips becomes long and thick.

The cutting tooth and the depth gauge together makes the cutting part of the saw chain, the cutter. The difference in height between the two gives the cutting depth (depth gauge setting).

When sharpening the cutter, consider the filing angle, cutting angle, file position, and round file diameter.

It is not easy to sharpen a saw chain correctly without the correct equipment. Use Husqvarna file gauge. This will help you to keep maximum cutting performance and the kickback risk at a minimum.

The force of the kickback increases a lot if you do not follow the sharpening instructions.

1. Use a round file and a file gauge to sharpen the cutting teeth.

2. Apply the file gauge correctly on to the cutter.

3. Move the file from the inner side of the cutting teeth and out. Decrease the pressure on the pull stroke.

4. Remove material from one side of all the cutting teeth.

5. Turn the HUSQVARNA 395 XPG product around and remove material on the other side.

6. Make sure that all cutting teeth are the same length.

The depth gauge setting decreases when you sharpen the cutting tooth. To keep maximum cutting performance you must remove filing material from the depth gauge to receive the recommended depth gauge setting.

The risk of kickback increases if the depth gauge setting is too large!

It is recommended to adjust the depth gauge setting after each third operation that you sharpen the cutting teeth.

1. Use a flat file and a depth gauge tool to adjust the depth gauge setting. Only use Husqvarna depth gauge tool to get the correct depth gauge setting and bevel for the depth gauge.

2. Put the depth gauge tool on the saw chain.

3. Use the flat file to remove the part of the depth gauge that extends through the depth gauge tool.

A saw chain with an incorrect tension can come loose from the guide bar and cause serious injury or death.

A saw chain becomes longer when you use it. Adjust the saw chain regularly.

1. Loosen the bar nuts that hold the clutch cover/chain brake. Use a wrench.

2. Tighten the bar nuts by hand as tightly as you can.

3. Lift the front of the guide bar and turn the chain tensioning screw. Use a wrench.

4. Tighten the saw chain until it is tight against the guide bar but still can move easily.

5. Tighten the bar nuts using the wrench and lift the front of the guide bar at the same time.

6. Make sure you can pull the saw chain around freely by hand and that it does not hang from the guide bar.

1. Start the HUSQVARNA 395 XPG product and let it operate at ¾ throttle. Hold the bar approximately 20 cm/8 in above a surface of light color.

2. If the saw chain lubrication is correct, you see a clear line of oil on the surface after 1 minute.

3. If the saw chain lubrication does not operate correctly, do a check of the guide bar. Speak to your servicing dealer if the maintenance steps do not help.

Regularly examine the chain drive sprocket for wear. Replace the chain drive sprocket if there is too much wear.

Replace the chain drive sprocket when you replace the saw chain.

Lubricate the needle bearing weekly.

1. Pull the front hand guard rearward to disengage the chain brake.

2. Loosen the bar nuts and remove the clutch cover.

3. Put the HUSQVARNA 395 XPG product on the side with the clutch up.

4. Use a grease gun to put engine oil in the center of the clutch as it rotates.

1. Make sure that there are no cracks in rivets and links and that no rivets are loose. Replace if it is necessary.

2. Make sure that the saw chain is easy to bend. Replace the saw chain if it is rigid.

3. Compare the saw chain with a new saw chain to examine if the rivets and links are worn.

4. Replace the saw chain when the longest part of the cutting tooth is less than 4 mm/0.16 in. Also replace the saw chain if there are cracks on the cutters.

1. Make sure that the oil channel is not blocked. Clean if it is necessary.

2. Examine if there are burrs on the edges of the guide bar. Remove the burrs using a file.

3. Clean the groove in the guide bar.

4. Examine the groove in the guide bar for wear. Replace the guide bar if it is necessary.

5. Examine if the guide bar tip is rough or very worn.

6. Make sure that the bar tip sprocket turns freely and that the lubricating hole in the bar tip sprocket is not blocked. Clean and lubricate if it is necessary.

7. Turn the guide bar daily to extend its life cycle.

Drain and clean the fuel tank and the chain oil tank regularly.

Replace the fuel filter yearly or more frequently if necessary.

Contamination in the tanks causes malfunction.

Stop the engine before you make adjustments to the oil pump.

1. Turn the adjustment screw for the oil pump. Use a screwdriver or combination wrench.

a) Turn the adjustment screw clockwise to decrease the chain oil flow.

b) Turn the adjustment screw counterclockwise to increase the chain oil flow.

Guide bar length 48-51 cm/18-20 in: 0 turn from initial position.

Guide bar length 51-61 cm/20-24 in: ¾ turns from initial position.

Guide bar length 61-71 cm/24-28 in: 1 ½ turns from initial position.

Guide bar length 71- cm/28- in: 1 ¾ turns from initial position.

AirInjection™ is a centrifugal air cleaning system that removes dust and dirt before the particles are caught by the air filter. AirInjection™ extends the life of the air filter and the engine.

1. Clean the cooling system with a brush weekly or more frequently if it is necessary.

2. Make sure that the cooling system is not dirty or blocked.

A dirty or blocked cooling system can make the HUSQVARNA 395 XPG product too hot, which can cause damage to the product.

Adjust or replace the starter pawls. Clean around the pawls. Speak to an approved service workshop.

Drain the fuel tank and fill with correct fuel.

If you have tried to start the HUSQVARNA 395 XPG product, speak to your servicing dealer. If you have not tried to start the product, drain the fuel tank.

Make sure that the spark plug is dry and clean.

Clean the spark plug. Make sure that the electrode gap and spark plug is correct, and that the correct spark plug type is the recommended or equivalent.

Tighten the spark plug.

Remove and clean the spark plug. Put the HUSQVARNA 395 XPG product on its side with the spark plug hole away from you. Pull the starter rope handle 6-8 times. Assemble the spark plug and start the product.

Drain the fuel tank and fill with correct fuel.

Speak to your servicing dealer.

Clean or replace the air filter.

Replace the fuel filter.

For storage and transportation of the HUSQVARNA 395 XPG product and fuel, make sure that there are no leaks or fumes. Sparks or open flames, for example from electrical devices or boilers, can start a fire.

Always use approved containers for storage and transportation of fuel.

Empty the fuel and chain oil tanks before transportation or before long-term storage. Discard the fuel and chain oil at an applicable disposal location.

Use the transportation guard on the HUSQVARNA 395 XPG product to prevent injuries or damage to the product. A saw chain that does not move can also cause serious injuries.

Remove the spark plug cap from the spark plug and engage the chain brake.

Attach the HUSQVARNA 395 XPG product safely during transportation.

1. Stop the HUSQVARNA 395 XPG product and let it become cool before you disassemble it.

2. Disassemble and clean the saw chain and the groove in the guide bar.

3. Attach the transportation guard.

4. Clean the HUSQVARNA 395 XPG product.

5. Do a complete servicing of the HUSQVARNA 395 XPG product.

If the saw chain and guide bar are not cleaned, they can become rigid or blocked.