GLOBE GCB48G-RK (01) PDF Document

The GLOBE GCB48G-RK must be installed on a solid, level, nonskid, and nonflammable surface away from sinks and water hazards.

Yes, the GLOBE GCB48G-RK is suitable for installation on non-combustible surfaces only. The required clearances are 6 inches from the sides, 6 inches from the rear, and 4 inches from the floor.

Level the GLOBE GCB48G-RK by adjusting the four feet until the unit sits level. Tighten them securely after adjustment. Do not slide the unit with the legs mounted; lift it if it needs to be moved.

Screw the legs into the permanently fastened nuts on the four corners of the GLOBE GCB48G-RK and tighten them by hand.

Use a soap and water solution to check all gas piping for leaks. Do not use an open flame to check for leaks on the GLOBE GCB48G-RK.

If you smell gas, immediately shut off the main gas valve to the GLOBE GCB48G-RK, extinguish all heat and flames, and call 911.

Ensure all knobs are in the OFF position. Turn the main gas valve to CLOSED/OFF for five minutes. Turn the main gas valve to ON/OPEN. Light and hold an ignition source at the pilot. Once established, remove the ignition source and repeat for each burner.

From the opening in the front panel of the GLOBE GCB48G-RK, use a screwdriver to turn the pilot valve screw. Turn it counterclockwise to increase the flame height. The flame should be as small as possible while ensuring reliable ignition.

To ignite the burner, turn the knob on the GLOBE GCB48G-RK to the ON position and then back off to the desired flame level.

Thoroughly wash the exterior of the GLOBE GCB48G-RK with a mild detergent or soap solution. Do not use abrasive cleaners. Burn off manufacturing oils and dust by running all burners at maximum for about an hour.

Turn the burners on the GLOBE GCB48G-RK about 15 to 20 minutes before cooking to preheat. Set the knobs to the desired temperature.

Place the rock racks over the burners of the GLOBE GCB48G-RK, then place the char rocks onto the rack. Do not pile or stack the rocks. For the GLOBE GCB48G-RK, use 96 pieces of char rocks.

Place the top cooking grates with the grid bars angled toward the front of the GLOBE GCB48G-RK to guide excess fat drippings into the grease trough, or place them flat.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB48G-RK daily. Wipe polished areas with a soft cloth.

Place the grates on the GLOBE GCB48G-RK with bars horizontal and facing down. Turn the broiler on for 45 minutes, then off for 20 minutes. Clean top and bottom surfaces with a wire brush, clean channels with a scraper, and remove grates to brush the radiants.

Always use insulated gloves when handling grates or radiants on the GLOBE GCB48G-RK to prevent burns. Do not cover the top of the grates during the burn off operation as this can cause warping or damage.

Once the GLOBE GCB48G-RK has cooled, remove the cast iron grates. Lift and rock the back support brace toward you, then lift it up and around the back support pins.

Angle the long lead edge of the brace down around the support pins of the GLOBE GCB48G-RK and rock the brace around the pins until it sits flat on the back ledge.

The catch tray on the GLOBE GCB48G-RK should be cleaned per use or at least daily. Remove it by pulling forward and discard the waste.

Close the gas valve to the GLOBE GCB48G-RK. Clean in place with a wire brush or clean gas ports with a sharp-pointed metal instrument. Alternatively, remove burners and wash in soapy water.

Check the regulator on the GLOBE GCB48G-RK monthly to ensure the vent is open and not blocked in any way.

Check that the main gas line is open. If so, try to ignite the pilot light. If the issue continues, contact a servicer for the GLOBE GCB48G-RK.

Adjust the flame height on the GLOBE GCB48G-RK by turning the control knob.

Adjust the pilot light flame height on the GLOBE GCB48G-RK. If the pilot tube is clogged, it will need to be replaced by a servicer.

Immediately turn off the main gas valve to the GLOBE GCB48G-RK. Do not light any flames or switch any electrical devices on or off. Contact the fire department and a servicer.

Ensure that the burners of the GLOBE GCB48G-RK are kept clean and free from carbon build-up or debris.

The GLOBE GCB48G-RK ships from the factory as natural gas, but conversion to L.P. gas is possible. Do not attempt this conversion on your own; contact an authorized servicer.

The controls should be turned off when not in use. Use a clean cloth to wipe down the controls and knobs of the GLOBE GCB48G-RK daily.

Do not use abrasive or flammable cleaning fluids on the GLOBE GCB48G-RK. Never use scrubber pads, steel wool, or cleaners containing chlorine, iodine, ammonia, or bromine.

No, do not hose down, immerse, or pressure wash any part of the GLOBE GCB48G-RK, excluding the catch tray.

Never leave the GLOBE GCB48G-RK on overnight. Keep the unit away from flammable vapors or liquids. Do not touch burners or grates while in operation. Always allow the unit to cool before cleaning or maintenance.

Owners should not allow anyone under 18 or untrained personnel to operate the GLOBE GCB48G-RK. Keep unauthorized personnel, customers, and visitors away from the unit.

The space between the legs of the GLOBE GCB48G-RK is where the unit draws in combustion air. Blocking this space can cause dangerous operating conditions.

If the stainless steel on the GLOBE GCB48G-RK becomes discolored, scrub by rubbing only in the direction of the finished grain.

Yes, all repairs, conversions of gas types, and adjustments to the balance of gas volume and air supply on the GLOBE GCB48G-RK must be performed by an authorized servicer.

The char grate back support brace on the GLOBE GCB48G-RK should be cleaned daily or as needed.

If the GLOBE GCB48G-RK is damaged, save all packaging and contact the carrier within 15 days of delivery. Also, immediately contact the service provider.

Yes, the cast iron cooking grates on the GLOBE GCB48G-RK will oxidize if emerged in water. Lightly oil them when not being used regularly.

If the catch tray of the GLOBE GCB48G-RK is permitted to fill too high, grease and debris may accumulate under the unit. Clean it daily or per use.

Do not allow fans to blow directly at the GLOBE GCB48G-RK or use wall fans that create cross-currents, as this can affect the burners and pilot flames.

Ensure that sufficient air can enter the room to compensate for the air removed by any ventilating system for the GLOBE GCB48G-RK to prevent subnormal atmospheric pressure.

The GLOBE GCB48G-RK does not contain any user-serviceable parts. Do not remove any service panels or attempt repairs.

Use a uniform and systematic approach to loading the GLOBE GCB48G-RK. When using different temperature settings, set adjoining areas at progressively higher temperatures.

Commissioning the GLOBE GCB48G-RK ensures that the unit functions properly and safely at the installation site, checking ventilation, gas installation, and operator training to avoid costly issues.

Always turn off the gas supply before servicing the GLOBE GCB48G-RK. Never attempt to alter the gas line or valves.

Exercise caution when handling or coming into contact with the GLOBE GCB48G-RK, as the manufacturing process can leave sharp edges on steel components.

No, you should never use the GLOBE GCB48G-RK as a room heating source.

If the GLOBE GCB48G-RK has been dropped or damaged in any way, do not operate it. Call for service immediately.

No, do not place any objects between the bottom of the GLOBE GCB48G-RK and the countertop, as this obstructs the flow of combustion air.

Any pipe threading compound used on the GLOBE GCB48G-RK must be resistant to the action of liquefied petroleum gases.

The regulator on the GLOBE GCB48G-RK should be checked monthly.