SONY BRAVIA KDL-46BX421 (03) PDF Document

Always unplug the power cord before cleaning to avoid electric shock. Wipe the LCD screen gently with a soft cloth. You may remove stubborn stains using a cloth slightly moistened with a solution of mild soap and warm water. Do not use strong solvents such as alcohol, benzine, or thinner for cleaning.

To experience stunning detail, you need access to high definition programming. You can receive this from an over the air broadcast via an HD quality antenna, an HD cable subscription, an HD satellite subscription, or a Blu ray Disc player or other HD compatible external equipment.

Before carrying the SONY BRAVIA KDL-46BX421, disconnect all cables. Use an adequate number of people to carry the unit, as larger size TVs require two or more people. Ensure correct hand placement while carrying to avoid damage.

If you move the SONY BRAVIA KDL-46BX421 from a cold area to a warm area, sudden temperature changes may cause moisture condensation, which may result in poor picture or poor color. Allow the moisture to evaporate completely before powering the TV on.

Connect one end of an HDMI cable to the HDMI output port on your HD cable or satellite box. Connect the other end of the same cable to one of the HDMI IN ports on the rear of the SONY BRAVIA KDL-46BX421.

To use the SONY BRAVIA KDL-46BX421 as a monitor for your PC, connect an HD15 to HD15 cable between the PC IN (RGB) jack on the TV and the monitor output of your computer. Additionally, connect an audio cable with stereo mini plugs between the PC/HDMI 1 AUDIO IN jack on the TV and the audio output of your PC.

Adequate ventilation is critical for the SONY BRAVIA KDL-46BX421. When installed with a stand, leave at least 11 7/8 inches (30 cm) of space above and 4 inches (10 cm) of space on the sides and behind the set. When installed on a wall, ensure similar clearance to prevent overheating, which can lead to equipment damage or a fire.

Sony recommends securing the SONY BRAVIA KDL-46BX421 to a wall or a stand. Use two angle braces (not supplied) to secure the TV stand to the wall, or anchor the TV to the wall using wall anchor holes, bolts, and a chain or rope. Avoid installing the TV on slippery or unstable surfaces, or furniture that can be used as steps.

Turn on the SONY BRAVIA KDL-46BX421 to display the Initial Setup screen. Use the arrow buttons on the remote control to highlight your preferred language and press the enter button to confirm. Follow the on screen prompts to select your viewing environment (Home or Retail) and run the Auto Program to scan for available digital and analog channels.

Open the battery compartment on the back of the remote control. Insert two AA size batteries, ensuring the positive and negative ends match the diagram inside the compartment, then close the cover.

The control buttons on the SONY BRAVIA KDL-46BX421 allow for basic operation without the remote. This includes a Power button to turn the TV on and off, Channel (CH) buttons to scan through channels, Volume buttons to adjust the audio level, and an Input button to toggle between external input sources.

Press the HOME button on the remote, select Settings, then go to Setup. Navigate to HDMI Settings, select Control for HDMI, and set it to On. This allows the SONY BRAVIA KDL-46BX421 to communicate with connected Sony equipment that supports this function.

While in PC mode, press the OPTIONS button on your remote. Select PIP from the menu to open an inset window displaying a TV channel or other external input. You can use the arrow buttons to move the sub window, or use the Audio Swap option in the same menu to switch audio between the main and sub windows.

While tuned to the channel you want to add, press the HOME button on your remote. Select Favorites, then highlight Add to Favorites and press the center button. This adds the current channel to the top of your favorites list.

Press the WIDE button on the SONY BRAVIA KDL-46BX421 remote control repeatedly to cycle through the available screen modes, such as Normal, Full, Zoom, or Wide Zoom, depending on the source material.

Press HOME, select Settings, then select the Setup option. Navigate to AV Setup and select Label Video Inputs. Choose the input you want to label (such as HDMI or Component), then select from the list of predefined names like VCR, DVD/BD, or Game to identify the connected equipment.

Connect a USB device to the USB port on the SONY BRAVIA KDL-46BX421. Press HOME, and select the Photo, Music, or Video icon using the remote. Navigate the file or folder list using the arrow keys, and press the center button to start playback of the selected file.

Press the HOME button, select the Settings icon, then select Picture. In this menu, you can adjust settings such as Backlight, Picture contrast, Brightness, Color, Hue, and Sharpness. You can also reset these to defaults or access Advanced Settings for finer control.

Scene Select on the SONY BRAVIA KDL-46BX421 optimizes picture and sound quality for specific content types. Options include Cinema, Sports, Photo, Music, Game, and Graphics. Setting this to Auto will automatically optimize settings based on the input source.

Press the HOME button, go to Settings, and select the Sound menu. You can customize the Sound Mode, adjust Treble and Bass, manage the Equalizer, set surround sound effects, and choose whether to output sound through the internal speakers or an external audio system.

Press the HOME button, navigate to Settings, then to the Setup menu. Select Sleep Timer and choose from the available time intervals (15, 30, 45, 60, 90, or 120 minutes) to have the SONY BRAVIA KDL-46BX421 shut off automatically.

Press HOME, select Settings, and navigate to the Parental Lock menu. You will need to enter your four-digit password. Once inside, select Channel Block, and follow the instructions to block specific channels regardless of their rating.

Turn on the SONY BRAVIA KDL-46BX421. While holding down the Up arrow button on the remote control, press the Power button on the TV itself. The TV will turn off and then back on automatically. Please note that this will clear all your customized settings, including Parental Lock.

Press the HOME button, select Settings, and go to the Eco menu. Here you can adjust Power Saving to Off, Low, High, or Picture Off. You can also configure the Idle TV Standby and Auto Shut Off features to have the SONY BRAVIA KDL-46BX421 power down when inactive or when no signal is detected.

You can toggle Closed Captions (CC) by pressing the CC button on the remote control, which cycles through the On, Off, and On when Muting modes. Additional detailed configurations for CC display, such as font style or color, can be adjusted in the Setup menu under Closed Captions (CC).

To view diagnostic information for the current signal on your SONY BRAVIA KDL-46BX421, press the HOME button, navigate to Settings, go to the Product Support menu, and select Signal Diagnostics.

When you are tuned to a channel that has been blocked by the Parental Lock feature on the SONY BRAVIA KDL-46BX421, press the center button on your remote control and enter your four-digit password to temporarily view the channel.

When the Power Saving mode is set to Picture Off on the SONY BRAVIA KDL-46BX421, the screen turns off while the sound remains on. Pressing the volume or mute buttons will not disable this; you must press other buttons on the remote or TV to restore the picture.

If you lose the password for the Parental Lock on your SONY BRAVIA KDL-46BX421, enter the master password 4357. This will clear the old password and allow you to set a new one.

Check the Power Saving settings in the Eco menu. Ensure the power cord is securely plugged in and the TV is turned on. Verify that cable or antenna connections are correct and that the Signal Type setting matches your source (Cable or Antenna).

Check the volume control to ensure it is not too low. Verify that you have not accidentally pressed the MUTING button on the SONY BRAVIA KDL-46BX421 remote control. Additionally, ensure the Speakers setting in the Sound menu is set to TV Speakers if you are using the built in speakers rather than an external audio system.

Due to the thin profile of the SONY BRAVIA KDL-46BX421, heat generated by the LCD panel backlight and the internal electronics is more noticeable. This is considered normal operation and is not a cause for concern.

The Favorites list on the SONY BRAVIA KDL-46BX421 will be automatically cleared each time you run the Auto Program for channel scanning or when you re-run the Initial Setup.

Press the HOME button, select Settings, and navigate to the Channel menu. Select Signal Type and choose Cable if you are using a cable service, or Antenna if you are using an over the air antenna with your SONY BRAVIA KDL-46BX421.

The SONY BRAVIA KDL-46BX421 supports JPEG photo files that conform to DCF 2.0 or Exif 2.21 standards, with the .jpg file extension.

Yes, the SONY BRAVIA KDL-46BX421 has a limit of 1,000 files or folders per directory for USB connected devices. If the number of files and folders exceeds this limit, they will not be displayed.

Yes, if the connected equipment is compatible with BRAVIA Sync and the Control for HDMI function is enabled on both devices, the SONY BRAVIA KDL-46BX421 remote control can manage basic operations of the connected equipment.

Press HOME, select Settings, go to the Setup menu, and select HDMI Settings. Select Device Control Keys. You can choose options like None, Tuning Keys, Menu Keys, or Tuning and Menu Keys to determine how the SONY BRAVIA KDL-46BX421 remote control interacts with the connected equipment.

On the SONY BRAVIA KDL-46BX421, the Timer LED lights up in orange when the sleep timer or Picture Frame feature is active. It lights up in green when the Power Saving mode is set to Picture Off.

While using Wide Zoom or Zoom modes, you can access the Screen settings menu on the SONY BRAVIA KDL-46BX421 to adjust the Horizontal Center and Vertical Center options to shift the picture position.

The Light Sensor on the SONY BRAVIA KDL-46BX421 detects the ambient room light level and automatically adjusts the screen brightness to optimize picture quality and power consumption. Ensure you do not block the sensor on the front of the TV.

Go to the Parental Lock settings in the SONY BRAVIA KDL-46BX421 menu and select Enter password. Use the 0-9 keys to input a four-digit code, and confirm it by entering it a second time.

Yes, the SONY BRAVIA KDL-46BX421 can be wall mounted. Sony recommends using the specific wall mount bracket designed for your model and having the installation performed by a professional dealer or licensed contractor to ensure safety and stability.

The SONY BRAVIA KDL-46BX421 supports various standard PC resolutions, including VGA (640×480), SVGA (800×600), XGA (1024×768), WXGA (1280×768 and 1360×768), SXGA (1280×1024), and HDTV (1920×1080) signals via the PC and HDMI input ports.

Double images or ghosts on the SONY BRAVIA KDL-46BX421 are often caused by poor antenna signal. Check all cable and antenna connections, and verify the antenna location and direction for optimal reception.

Press the HOME button, go to Settings, and select Channel. Choose Add Digital Channels, and select OK to scan for and add any new digital channels that were not captured during the initial setup on your SONY BRAVIA KDL-46BX421.

Access the Channel menu in the SONY BRAVIA KDL-46BX421 Settings, then choose Show/Hide Channels. Scroll through the channel list using the arrow keys, press the center button to select the channel you wish to hide, and then change the setting to indicate it is hidden.

In the Setup menu of the SONY BRAVIA KDL-46BX421, you can select Picture Adjustments Lock. Setting this to Lock prevents further changes to the picture settings, while setting it to Unlock allows you to modify them.

In the Channel Settings menu of the SONY BRAVIA KDL-46BX421, select Label Channels. Select the channel number you want to rename, then use the arrow keys to scroll through the characters and assign a new label of up to seven characters.

Yes, the SONY BRAVIA KDL-46BX421 includes an Idle TV Standby feature in the Eco settings, which can be configured to power off the TV after 1, 2, or 4 hours of inactivity.

Press the HOME button, go to Settings, and select Product Support. The SONY BRAVIA KDL-46BX421 will display system information, including the model name, serial number, and current software version.

In the Picture settings for the SONY BRAVIA KDL-46BX421, you can adjust Noise Reduction and MPEG Noise Reduction to High, Medium, or Low to help reduce picture artifacts and graininess common in lower resolution broadcast sources.

Test the TV’s physical buttons to confirm the issue is with the remote. Check the battery polarity or replace them. Ensure the path to the IR sensor on the SONY BRAVIA KDL-46BX421 is clear and that there is no interference from fluorescent lighting.

Press the HOME button, select Settings, navigate to the Setup menu, and select Language. From here, you can choose between English, Español, or Français to display the on-screen settings for the SONY BRAVIA KDL-46BX421.

When enabled in the Eco settings, the Auto Shut Off function on the SONY BRAVIA KDL-46BX421 will automatically power off the TV if no input signal is detected for a certain period of time.

In the Screen settings menu of the SONY BRAVIA KDL-46BX421, select 4:3 Default. You can then choose between options like Normal, Wide Zoom, Full, or Zoom to determine how the TV stretches or formats 4:3 aspect ratio content.

This is common when a channel switches from HD to SD content. You can manually change the Wide Mode on your SONY BRAVIA KDL-46BX421 using the remote if the automatic detection is not desired for that specific content.

The Standby LED on the front of the SONY BRAVIA KDL-46BX421 will light up in red when the TV is in standby mode.

In the Picture settings menu, select Color Temperature. You can choose from Cool (bluish tint), Neutral (neutral tint), or Warm 1/Warm 2 (reddish tints) to customize the color output of the SONY BRAVIA KDL-46BX421.

Yes. Navigate to the Setup menu within the Settings, and toggle Start-up Sound to Off on your SONY BRAVIA KDL-46BX421.

In the Sound settings menu, use the Volume Offset option. This allows you to set the volume level for the current input of the SONY BRAVIA KDL-46BX421 relative to other inputs.