GLOBE GCB15G-RK (01) PDF Document

You must install the GLOBE GCB15G-RK in a work area with adequate light and space. Only operate the unit on a solid, level, nonskid surface that is nonflammable and away from sinks and water hazards. The area must be well lit and kept away from children and visitors.

No, you should never bypass, alter, or modify the GLOBE GCB15G-RK in any way from its original condition. Doing so may create hazards and will void the warranty.

The GLOBE GCB15G-RK is factory supplied in Natural Gas. It can be converted to L.P. gas by a licensed and certified gas technician.

The required non-combustible clearances are: 6 inches on the sides, 6 inches at the rear, and 4 inches from the floor.

Level the GLOBE GCB15G-RK by adjusting the four feet until the unit is steady. Tighten the feet securely. Do not slide the unit with the legs mounted; lift the unit if you need to move it.

Do not use an open flame to check for leaks. Check all gas piping for leaks on the GLOBE GCB15G-RK with a soap and water solution before operating the unit.

Immediately shut off the main gas valve, extinguish all heat and flames, and follow emergency safety protocols. Do not turn on any electrical switches or ignite anything.

Repairs and conversions on the GLOBE GCB15G-RK are to be made solely by an authorized servicer. Do not attempt to repair or convert any gas types on your own.

No, the GLOBE GCB15G-RK does not contain any user-serviceable parts. Do not remove any components or service panels.

Step 1. Make sure all knobs are in the OFF position.

Step 2. The main gas valve should be CLOSED/OFF for five minutes prior to lighting pilots to clear any existing gas.

Step 3. Turn the main gas valve to ON/OPEN.

Step 4. Light and hold an ignition source at the pilot. When the flame is established, remove the ignition source. Repeat this for each burner.

Step 5. Turn each burner knob ON. If burners do not ignite, turn knobs OFF, use a screwdriver to turn the pilot valve screw counterclockwise to increase flame height, and repeat.

To ignite the burner, turn the knob on the GLOBE GCB15G-RK to the ON position. Then back off to the desired flame level.

No, the space between the legs at the bottom admits combustion air to the GLOBE GCB15G-RK. Do not block this space.

Prior to operating your new GLOBE GCB15G-RK, thoroughly wash the exterior with a mild detergent or soap solution. Turn the burners on about 15 to 20 minutes before cooking for preheating. When the unit is first heated, it will smoke until manufacturing oil and dust are burned off. An hour at maximum for all burners is usually sufficient.

Place the racks that hold the rocks into position over the burners of the GLOBE GCB15G-RK. Place the char rocks on the rack. Do not pile or stack the char rocks. For the GCB15G-RK model, use 24 pieces.

Place the top cooking grates on the GLOBE GCB15G-RK with the grid bars angled toward the front, or place the grid bars flat, not angled, for cooking. When placed angled toward the front, the grooves on top will guide the excess fat drippings into the grease trough.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB15G-RK daily. Wipe the polished areas with a soft cloth.

Do not use any abrasive or flammable cleaning fluids on the GLOBE GCB15G-RK. Never use a scrubber pad, steel wool, or abrasive material, or cleaners containing chlorine, iodine, ammonia, or bromine chemicals.

Step 1. Place grates on the GLOBE GCB15G-RK with grid bars horizontal and facing down.

Step 2. Turn the broiler on for approximately 45 minutes.

Step 3. Turn off the broiler and allow it to cool for 20 minutes.

Step 4. Clean top and bottom surfaces of the grate with a wire brush to remove animal fats and carbonized grease.

Step 5. Clean channels on grates with a scraper.

Step 6. Remove grates and clean the top surface of radiants with a wire brush.

Once the GLOBE GCB15G-RK has cooled, remove the cast iron grates. Lift and rock the back support brace toward you; lift the char grate back support brace up and around the back support pins. Clean and de-grease the support brace. To reinstall, angle the long lead edge of the grate back support brace down around the support pins and rock the back support brace around the pins until it is seated flat on the back ledge.

Once the GLOBE GCB15G-RK has cooled, remove the catch tray by pulling it forward. Discard the waste, grease, debris, and crumbs. Do not allow the tray to fill too high, as grease or debris may accumulate under the unit.

First, close the gas valve to the GLOBE GCB15G-RK to shut off the gas and extinguish the pilot light. Clean in place with a wire brush, or clean gas ports with a sharp-pointed metal instrument to ensure they are open. Alternatively, the burners may be removed and washed in soapy water for 15 to 20 minutes.

You should make sure the vent is open and not blocked in any way on a monthly basis for the GLOBE GCB15G-RK.

Check if the main gas line is closed; if so, open the valve. Check if the pilot light is lit; if not, ignite the pilot light. If the cause is unknown, call for service.

Adjust the flame on the GLOBE GCB15G-RK using the control knob.

If the flame is too low, adjust the pilot light flame height. If the pilot tube is clogged, replace the pilot tube or call for service.

Immediately turn off the main gas valve. Do not light any flame, do not ignite anything, and do not turn or switch on anything electrical. Call the fire department if needed and call for service.

Carbon build-up is likely the cause. Ensure that the burners of the GLOBE GCB15G-RK are kept clean and free from carbon build-up and debris.

Yes, the GLOBE GCB15G-RK ships from the factory as Natural gas, but conversion to L.P. is possible. You must contact an authorized servicer. Do not attempt the conversion on your own.

Turn the GLOBE GCB15G-RK off when not in use. It is recommended that the unit be disconnected from the gas supply by closing the main gas valve, and then use a clean cloth to wipe down the controls and knobs daily.

When handling the grates, grids, or radiants of the GLOBE GCB15G-RK, always use insulated gloves to prevent burns. Do not cover the top of the grates during a burn-off operation, as restricting airflow may cause them to warp and damage the valves, knobs, and front panel.

The body of the GLOBE GCB15G-RK should be cleaned daily using a clean cloth and a non-abrasive cleaner.

The main gas valve of the GLOBE GCB15G-RK must be switched to the closed position. After cleaning, the gas line can be switched back to the open position, and you must follow the lighting instructions to relight the pilot lights.

No, do not use the GLOBE GCB15G-RK outdoors.

No, never use the GLOBE GCB15G-RK as a heating source.

Do not operate the GLOBE GCB15G-RK if the unit is dropped or damaged in any manner. Call for service.

Yes, do not permit fans to blow directly at the GLOBE GCB15G-RK. Avoid open windows next to the unit’s sides or back, and avoid wall-type fans which create air cross-currents within a room. Ensure sufficient air is allowed to enter the room to compensate for the ventilation system.

When the GLOBE GCB15G-RK is first heated, it will smoke until the oil used in manufacturing and dust from storage and shipping are burned off.

The cooking grates on the GLOBE GCB15G-RK are heavy-duty cast iron, which will oxidize if emerged in water. Lightly oil the grates when not being used regularly.

Use a uniform and systematic approach to loading the GLOBE GCB15G-RK. If different temperature settings are used, adjoining areas should be set at progressively higher temperatures using the lowest temperatures on the outside burners.

The GLOBE GCB15G-RK must be connected to an individual shutoff valve that is supplied by the user. This valve must be disconnected from the gas supply piping system during any pressure testing in excess of 1/2 psi.

If any warning labels on the GLOBE GCB15G-RK are misplaced, damaged, or illegible, contact a representative to obtain these items.

No, never leave the GLOBE GCB15G-RK on overnight.

Yes, the GLOBE GCB15G-RK must be properly maintained and operated in accordance with the provided instructions to ensure safe and productive processing, cooking, and warming of food products.

Keep the area around the GLOBE GCB15G-RK free and clear of combustibles. Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.

Yes, the burners, cooking grates, and outside surfaces of the GLOBE GCB15G-RK will become hot after use. Use caution when touching the unit and allow it to cool down before dismantling for cleaning.

There must be adequate clearance for removal of the front panel on the GLOBE GCB15G-RK. All major parts, except the burners, are removable through the front if the gas line is disconnected.

The pipe threading compound used for the GLOBE GCB15G-RK must be resistant to the action of liquefied petroleum gases.

Owners should not permit anyone to touch the GLOBE GCB15G-RK unless they are over 18 years old, are adequately trained and supervised, and have read and understood the instruction manual.

Always turn off the GLOBE GCB15G-RK when not in use, when servicing, or adjusting any parts or attachments, and before cleaning.

Yes, the GLOBE GCB15G-RK must be installed under proper ventilation as required per local code. A properly designed and installed hood will act as the heart of the ventilation system.

The pilot flame on the GLOBE GCB15G-RK should be as small as possible, but large enough to guarantee reliable ignition of the burners when the knobs are turned to ON. Use the pilot valve adjustment holes in the front panel to adjust the flame height with a screwdriver.

Yes, always keep hands, hair, and clothing away from the heating source of the GLOBE GCB15G-RK.

Do not operate any equipment with a damaged or leaking gas line on the GLOBE GCB15G-RK. Call for service immediately.