GLOBE GCB15G-CR (01) PDF Document

Owners should not permit anyone to touch the GLOBE GCB15G-CR unless they are over 18 years old, are adequately trained and supervised, and have read and understood the manual. Additionally, owners must ensure that no customers, visitors or other unauthorized personnel come in contact with this equipment.

If you smell gas, immediately shut off the main gas valve, extinguish all heat and flames, and call emergency services. All safety precautions must be taken in this event.

The GLOBE GCB15G-CR must be installed on a solid, level, nonskid surface that is nonflammable and away from sinks and water hazards. It must be in a well lit work area away from children and visitors.

No, you should never bypass, alter or modify the GLOBE GCB15G-CR in any way from its original condition. Doing so may create hazards and will void the warranty.

The GLOBE GCB15G-CR is suitable for installation on non-combustible surfaces only. The required clearances are: 6 inches on the sides, 6 inches at the rear, and 4 inches from the floor.

Level the GLOBE GCB15G-CR by adjusting the four feet until the unit is level, then tighten them securely. The feet have an adjustment of one inch to allow alignment with other countertop products.

Do not use an open flame to check for leaks. Check all gas piping for leaks on the GLOBE GCB15G-CR with a soap and water solution before operating the unit.

Before operating, check that the GLOBE GCB15G-CR is sitting level. Ensure that the catch tray is properly placed and make sure all knobs are in the OFF position.

First, make sure all knobs are in the OFF position. The main gas valve should be closed for five minutes prior to lighting pilots to clear any existing gas. Turn the main gas valve to ON. Light and hold an ignition source at the pilot. When the flame is established, remove the ignition source. Repeat this for each burner.

If the burners on the GLOBE GCB15G-CR do not ignite promptly, turn the knobs OFF. From the opening in the front panel, use a screwdriver and turn the pilot valve screw counterclockwise to increase the flame height, then repeat the lighting procedure.

To ignite the burner on the GLOBE GCB15G-CR, turn the knob to the ON position. Then back off to the desired flame level.

Turn the burners on the GLOBE GCB15G-CR about 15 to 20 minutes before cooking for preheating. Set the knobs to the desired flame height or temperature.

When the GLOBE GCB15G-CR is first heated, it will smoke until the oil used in manufacturing and dust from storage and shipping are burned off. An hour at maximum for all burners is usually sufficient.

Place the top cooking grates on the GLOBE GCB15G-CR with the grid bars angled toward the front, or place the grid bars flat if desired. When angled toward the front, the grooves on top will guide excess fat drippings into the grease trough.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB15G-CR on a daily basis. Wipe the polished areas with a soft cloth.

Place grates on the GLOBE GCB15G-CR with grid bars horizontal and facing down. Turn the broiler on for approximately 45 minutes, then turn off and allow to cool for 20 minutes. Clean top and bottom surfaces of the grate with a wire brush to remove animal fats and carbonized grease. Clean channels on grates with a scraper. Remove grates and clean the top surface of radiants with a wire brush.

Yes, do not cover the top of the grates on the GLOBE GCB15G-CR during a burn off operation. Restricting the airflow by covering the grid grates may cause them to warp and will cause damage to the valves, knobs, and the front panel decal.

Once the GLOBE GCB15G-CR has cooled, remove the cast iron grates. Lift and rock the back support brace toward you, then lift the char grate back support brace up and around the back support pins.

Angle the long lead edge of the grate back support brace on the GLOBE GCB15G-CR down around the support pins and rock the back support brace around the pins until it is seated flat on the back ledge.

Once the GLOBE GCB15G-CR has cooled, remove the catch tray by pulling it forward.

Close the gas valve to the GLOBE GCB15G-CR, shutting off the gas and extinguishing the pilot light. Clean in place with a wire brush or clean gas ports with a sharp pointed metal instrument. Alternatively, the burners may be removed and washed in soapy water for 15 to 20 minutes.

Check the regulator on the GLOBE GCB15G-CR monthly to make sure the vent is open and not blocked in any way. Failure to do so will cause variations in pressure, which affects function and could shorten the life of the product.

Check if the main gas line is closed and open it. Ensure the pilot light is lit. If the issue persists, contact a servicer.

The adjustment knob has been turned up or down. Adjust the flame on the GLOBE GCB15G-CR to the desired level using the control knob.

If the flame is too low, adjust the pilot light flame height. If the pilot tube is clogged, it must be replaced by a servicer.

There may be a main gas line leak. Turn off the main gas valve to the GLOBE GCB15G-CR immediately. Do not light flames, ignite anything, or turn on or switch on any electrical devices. Contact the fire department if needed and call for service.

This is likely caused by carbon build up. Ensure that the burners on the GLOBE GCB15G-CR are kept clean and free from carbon build up or debris.

Yes, the GLOBE GCB15G-CR ships from the factory for natural gas, but conversion to L.P. is possible. This must be done by a licensed and certified gas technician using the included L.P. conversion kit.

Do not use any abrasive or flammable cleaning fluids. Never use a scrubber pad, steel wool, or abrasive material, or cleaners containing chlorine, iodine, ammonia, or bromine chemicals as these will deteriorate the stainless steel and shorten the life of the GLOBE GCB15G-CR.

When handling grates, grids, or radiants on the GLOBE GCB15G-CR, always use insulated gloves to prevent burns.

No, do not hose down, immerse, or pressure wash any part of the GLOBE GCB15G-CR, excluding the catch tray.

The body of the GLOBE GCB15G-CR should be cleaned daily.

The controls of the GLOBE GCB15G-CR should be cleaned daily.

The catch tray on the GLOBE GCB15G-CR should be cleaned after every use or at least daily.

Yes, the GLOBE GCB15G-CR must be installed under proper ventilation as required per local code.

Always keep hands, hair, and clothing away from the heating source of the GLOBE GCB15G-CR. Allow the unit to cool down after use and before dismantling for cleaning, as it will be too hot to handle immediately after use.

Save the packaging material and contact the carrier within fifteen days of delivery. Immediately contact service or your local dealer for the GLOBE GCB15G-CR. You have no recourse for damage after fifteen days of receipt.

Do not permit fans to blow directly at the GLOBE GCB15G-CR. Wherever possible, avoid open windows next to the sides or back of the unit. Avoid wall type fans which create air cross-currents within a room.

If the stainless steel surfaces of the GLOBE GCB15G-CR become discolored, scrub by rubbing only in the direction of the finished grain.

The space between the legs at the bottom of the GLOBE GCB15G-CR admits combustion air. Do not block this space.

If the catch tray of the GLOBE GCB15G-CR is permitted to fill too high, grease and debris are likely to accumulate under the unit.

Any pipe threading compound used during the installation of the GLOBE GCB15G-CR must be resistant to the action of liquefied petroleum gases.

No, you should never leave the GLOBE GCB15G-CR on overnight.

No, do not use the GLOBE GCB15G-CR outdoors.

Do not operate the GLOBE GCB15G-CR if it is dropped or damaged in any manner. Call for service.

No, never use the GLOBE GCB15G-CR as a heating source.

No, the GLOBE GCB15G-CR does not contain any user-serviceable parts. Qualified technicians should carry out all repairs.

Do not obstruct the flow of combustion and ventilation air under the GLOBE GCB15G-CR by the legs, or behind the unit by the flue. Do not place objects between the bottom of the unit and the countertop.

All burners on the GLOBE GCB15G-CR are lit from constantly burning pilots. Turning the valve to the desired flame height is all that is required to put the unit in service.

Always turn off the GLOBE GCB15G-CR when not in use, when servicing, or adjusting any parts or attachments, and before cleaning.

Steel cutting procedures used to manufacture the GLOBE GCB15G-CR result in sharp edges. While these edges are removed to the best of the manufacturer’s ability, operators should take care when in contact with this piece of equipment.

The burner air shutter openings of the GLOBE GCB15G-CR should be cleaned as needed.

The supplied gas pressure regulator for the GLOBE GCB15G-CR is factory set at 6 inches W.C. for Natural gas or 10 inches W.C. for L.P.