GLOBE GCB48G-SR (01) PDF Document

The GLOBE GCB48G-SR must be installed on a solid, level, nonskid surface that is nonflammable and away from water hazards or sinks. It must be in a well-lit work area and installed under proper ventilation as required by local codes.

The GLOBE GCB48G-SR requires the following clearances from non-combustible surfaces: 6 inches on the sides, 6 inches in the rear, and 4 inches from the floor.

Screw the legs into the permanently fastened nuts on the four corners of the GLOBE GCB48G-SR and tighten them by hand. The legs must be installed to adequately provide proper ventilation to the unit.

Level the GLOBE GCB48G-SR by adjusting the four feet and tightening them securely. Do not slide the unit with the legs mounted; lift it if necessary to move it.

Never use an open flame to check for leaks. Always check all gas piping for leaks using a soap and water solution before operating the GLOBE GCB48G-SR. Ensure the appliance and its individual shutoff valve are disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi.

Immediately shut off the main gas valve, extinguish all heat and flames, and call 911. Instructions regarding this must be posted in a prominent location.

First, ensure all knobs are in the OFF position. The main gas valve should be closed for five minutes prior to lighting to clear any existing gas. Turn the main gas valve to ON. Light and hold an ignition source at the pilot. When the flame is established, remove the ignition source. Repeat this for each burner.

To ignite the burner, turn the knob to the ON position. Then back off to the desired flame level.

Turn the knobs to the OFF position. From the opening in the front panel, use a screwdriver and turn the pilot valve screw counterclockwise to increase the flame height, then try again.

The holes located in the front panel of the GLOBE GCB48G-SR are for pilot valve adjustments. Use a screwdriver to turn the valve to adjust the flame to the desired level. It should be as small as possible but large enough to guarantee reliable ignition.

Turn the burners on the GLOBE GCB48G-SR about 15 to 20 minutes before cooking. Set the knobs to the desired flame height or temperature.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB48G-SR. Wipe the polished areas with a soft cloth. Perform this daily.

Place grates on the GLOBE GCB48G-SR with grid bars horizontal and facing down. Turn the broiler on for approximately 45 minutes, then turn it off and allow it to cool for 20 minutes. Clean top and bottom surfaces of the grate with a wire brush to remove animal fats and carbonized grease. Clean the channels on the grates with a scraper. Remove the grates and clean the top surface of the radiants with a wire brush.

After the GLOBE GCB48G-SR has cooled and the cast iron grates have been removed, lift and rock the back support brace toward you. Lift the char grate back support brace up and around the back support pins. Clean and de-grease the brace. To reinstall, angle the long lead edge of the brace down around the support pins and rock it around the pins until it is seated flat on the back ledge.

Once the unit has cooled, pull the catch tray forward to remove it. Discard the waste, grease, debris, and crumbs. Perform this per use or at least daily.

Close the gas valve to the GLOBE GCB48G-SR, shutting off the gas and extinguishing the pilot light. Clean in place with a wire brush, or clean gas ports with a sharp-pointed metal instrument. Alternatively, the burners may be removed and washed in soapy water for 15 to 20 minutes.

Ensure the vent on the GLOBE GCB48G-SR regulator is open and not blocked in any way. Perform this check monthly.

First, check if the main gas line is closed and open the valve if necessary. Second, check if the pilot light is lit and ignite it if needed. If the cause is unknown, request service.

Adjust the flame using the control knob on the GLOBE GCB48G-SR.

Either the flame is too low, requiring an adjustment to the pilot light flame height, or the pilot tube is clogged, requiring replacement.

Turn off the main gas valve. Do not light flames, ignite anything, or turn/switch on anything electrical. Call the fire department if needed and call for service.

This is likely caused by carbon build up. Ensure that the burners are kept clean and free from carbon build up and debris.

Do not use any abrasive or flammable cleaning fluids. Do not hose down, immerse, or pressure wash any part of the GLOBE GCB48G-SR, excluding the catch tray. Never use a scrubber pad, steel wool, or abrasive material, or cleaners containing chlorine, iodine, ammonia, or bromine.

When handling grates, grids, or radiants on the GLOBE GCB48G-SR, always use insulated gloves to prevent burns.

Do not cover the top of the grates grid during a burn off operation. Restricting the airflow may cause them to warp and will also cause damage to the valves, knobs, and front panel decal of the GLOBE GCB48G-SR.

Daily. The unit should be turned off when not in use. It is recommended that the unit be disconnected from the gas supply by closing the main gas valve. Use a clean cloth to wipe down controls and knobs.

The cooking grates, cast iron radiants, and char rock grids are heavy duty cast iron which will oxidize if submerged in water. Lightly oil these parts of the GLOBE GCB48G-SR when not being used regularly.

The GLOBE GCB48G-SR is for commercial use only. Do not use it outdoors, do not use it as a heating source, and do not use it for any purpose other than what it was intended for by the manufacturer.

The burners, cooking grates, and outside surfaces of the GLOBE GCB48G-SR will become hot after use. Allow the unit to cool down before dismantling for cleaning.

Do not operate the GLOBE GCB48G-SR with a damaged or leaking gas line, ignitor, or valves, or if the unit is dropped or damaged in any manner.

Never bypass, alter, modify, or attach any unauthorized parts to the GLOBE GCB48G-SR. Doing so may create hazards and will void the warranty.

Place the top cooking grates with the grid bars angled toward the front, or place the grid bars flat, not angled, for cooking.

When cooking grates on the GLOBE GCB48G-SR are placed angled toward the front, the grooves on top will guide the excess fat drippings into the grease trough.

When the GLOBE GCB48G-SR is first heated, it will smoke until oil used in manufacturing and dust from storage and shipping are burned off. An hour at maximum for all burners is usually sufficient.

If the stainless steel surfaces on the GLOBE GCB48G-SR become discolored, scrub by rubbing only in the direction of the finished grain.

The space between the legs at the bottom of the GLOBE GCB48G-SR admits combustion air. Do not block this space.

Do not permit fans to blow directly at the GLOBE GCB48G-SR. Avoid open windows next to the sides or back of the unit. Avoid wall type fans which create air cross-currents within a room. Ensure sufficient air is allowed to enter the room to compensate for the amount of air removed by any ventilating system.

The supplied gas pressure regulator for the GLOBE GCB48G-SR is factory set at 6 inches water column for Natural gas or 10 inches for L.P.

Yes, the GLOBE GCB48G-SR ships from the factory set for Natural Gas but can be converted to L.P. gas. This must be done by a licensed and certified gas technician using the included L.P. conversion kit.

There must be adequate clearance for the removal of the front panel on the GLOBE GCB48G-SR.

Pipe threading compound used on the GLOBE GCB48G-SR must be resistant to the action of liquefied petroleum gases.

Before operating the GLOBE GCB48G-SR, thoroughly wash the exterior with a mild detergent or soap solution. Do not use abrasive cleaners. Check that the unit is sitting level by adjusting the feet, and ensure the catch tray has been properly placed.

If different temperature settings are to be used on the GLOBE GCB48G-SR, adjoining areas should be set at progressively higher temperatures using the lowest temperatures on the outside burners.

No, the GLOBE GCB48G-SR does not contain any user-serviceable parts. Repairs are to be carried out by qualified technicians.

Place the angled radiants into position, ensuring they are setting properly into the slots on the front and rear supports of the GLOBE GCB48G-SR. Radiants should be centered over straight sections of the burners.

First, place the racks that hold the rocks into position over the burners. Second, place the char rocks on the rack. Do not pile or stack the char rocks.

Owners should not permit anyone to touch the GLOBE GCB48G-SR unless they are over 18 years old, are adequately trained, supervised, and have read the manual. Ensure no customers, visitors, or other unauthorized personnel come in contact with the equipment.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB48G-SR. Wipe the polished areas with a soft cloth. Never use abrasive cleaners, which might damage the cabinet finish.

Restricting the airflow on the GLOBE GCB48G-SR by covering the grid grates during a burn off may cause them to warp. It will also cause damage to the valves, the knobs, and the front panel decal.

If any warning labels or the manual for the GLOBE GCB48G-SR are misplaced, damaged, or illegible, contact your nearest representative for replacements.