GLOBE GCB36G-RK (01) PDF Document

You must only operate the GLOBE GCB36G-RK on a solid, level, nonskid surface that is nonflammable and away from sinks and water hazards.

The GLOBE GCB36G-RK is factory supplied in Natural Gas. It can be converted to L.P. gas by a licensed and certified gas technician using the included conversion kit.

The GLOBE GCB36G-RK is suitable for installation on non-combustible surfaces only. The required clearances are 6 inches for sides, 6 inches for the rear, and 4 inches for the floor.

Screw the legs into the permanently fastened nuts on the four corners of the GLOBE GCB36G-RK and tighten them by hand.

Level the GLOBE GCB36G-RK by adjusting the four feet and tightening them securely. The feet have an adjustment of one inch.

If you smell gas, immediately shut off the main gas valve to the GLOBE GCB36G-RK, extinguish all heat and flames, and call emergency services.

Check all gas piping for leaks on the GLOBE GCB36G-RK using a soap and water solution. Do not use an open flame to check for leaks.

First, make sure all knobs are in the OFF position. Second, ensure the main gas valve has been closed for five minutes. Third, turn the main gas valve to ON. Fourth, light and hold an ignition source at the pilot for each burner. Once established, turn the burner knob to ON.

From the opening in the front panel, use a screwdriver to turn the pilot valve screw counterclockwise to increase the flame height. The pilot flame should be as small as possible while still guaranteeing reliable ignition.

To ignite the burner, turn the knob to the ON position and then back off to the desired flame level.

Turn the burners of the GLOBE GCB36G-RK on about 15 to 20 minutes before cooking for preheating.

The GLOBE GCB36G-RK requires 72 pieces of char rocks.

Place the top cooking grates with the grid bars angled toward the front to guide excess fat drippings into the grease trough, or place them flat for cooking.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body of the GLOBE GCB36G-RK daily. Wipe polished areas with a soft cloth.

First, place grates on the GLOBE GCB36G-RK with grid bars horizontal and facing down. Turn the broiler on for 45 minutes, then turn it off and allow it to cool for 20 minutes. Clean top and bottom surfaces with a wire brush, clean channels with a scraper, and clean the radiants with a wire brush.

After the GLOBE GCB36G-RK has cooled, remove the catch tray by pulling it forward and discard the waste, grease, debris, and crumbs. This should be done per use or at least daily.

Close the gas valve, then clean the main burner ports on the GLOBE GCB36G-RK in place with a wire brush, or clean gas ports with a sharp-pointed metal instrument. Alternatively, remove the burners and wash them in soapy water.

The regulator vent on the GLOBE GCB36G-RK must be checked monthly to ensure it is open and not blocked.

If the GLOBE GCB36G-RK will not light, check that the main gas line is open. If it is, attempt to ignite the pilot light. If it still will not light, call for service.

If the pilot light on the GLOBE GCB36G-RK does not stay lit, the flame may be too low; adjust the pilot flame height. If the pilot tube is clogged, call for service to replace the tube.

If there is a strong smell of gas near the GLOBE GCB36G-RK, turn off the main gas valve immediately. Do not light flames or turn on any electrical switches. Call the fire department if needed and call for service.

If the GLOBE GCB36G-RK is heating up slowly, it is likely due to carbon build up on the burners. Ensure that the burners are kept clean and free from carbon build up or debris.

Yes, the GLOBE GCB36G-RK ships from the factory as Natural Gas, but conversion to L.P. is possible. This must be handled by an authorized servicer. Do not attempt conversion on your own.

Yes, always use insulated gloves when handling the grates, grids, or radiants on the GLOBE GCB36G-RK to prevent burns.

Use a clean cloth and a non-abrasive cleaner to clean the stainless steel body, then wipe the polished areas with a soft cloth.

The unit should be turned off when not in use. It is recommended to disconnect the gas supply by closing the main gas valve, and use a clean cloth to wipe down the controls and knobs of the GLOBE GCB36G-RK daily.

After cleaning the burner of the GLOBE GCB36G-RK, the gas line can be switched back to the open position, and you must follow the lighting instructions to relight the pilot lights.

No, do not use any abrasive or flammable cleaning fluids on the GLOBE GCB36G-RK, as this will damage the finish.

No, do not hose down, immerse, or pressure wash any part of the GLOBE GCB36G-RK, excluding the catch tray.

Never use a scrubber pad, steel wool, or abrasive material, or cleaners containing chlorine, iodine, ammonia, or bromine chemicals on the GLOBE GCB36G-RK.

Once the GLOBE GCB36G-RK has cooled, remove the cast iron grates, then lift and rock the back support brace toward you; lift it up and around the back support pins.

Angle the long lead edge of the grate back support brace down around the support pins on the GLOBE GCB36G-RK and rock the back support brace around the pins until it is seated flat on the back ledge.

Do not cover the top of the grates grid during a burn off operation on the GLOBE GCB36G-RK, as restricting airflow may cause them to warp and cause damage to the valves, knobs, and front panel decal.

If the stainless steel surfaces of the GLOBE GCB36G-RK become discolored, scrub by rubbing only in the direction of the finished grain.

When the GLOBE GCB36G-RK is first heated, it will smoke until manufacturing oil and storage dust are burned off. An hour at maximum for all burners is usually sufficient.

Do not permit fans to blow directly at the GLOBE GCB36G-RK. Avoid open windows next to the unit’s sides or back, and avoid wall type fans which create air cross-currents.

Sufficient air must be allowed to enter the room to compensate for the amount of air removed by any ventilating system for the GLOBE GCB36G-RK to operate properly.

No, you should never leave the GLOBE GCB36G-RK on overnight.

No, you should never use the GLOBE GCB36G-RK as a heating source.

The GLOBE GCB36G-RK does not contain any user-serviceable parts. Qualified technicians should carry out repairs.

Steel cutting procedures used to manufacture the GLOBE GCB36G-RK result in sharp edges. Operators should take care when in contact with this piece of equipment.

The cooking grates of the GLOBE GCB36G-RK are heavy duty cast iron which will oxidize if emerged in water. Lightly oil grates when not being used regularly.

If the catch tray of the GLOBE GCB36G-RK is permitted to fill too high, grease and debris are likely to accumulate under the unit.

Do not operate the GLOBE GCB36G-RK if the unit is dropped or damaged in any manner. Call for service.

Owners should not permit anyone to touch the GLOBE GCB36G-RK unless they are over 18 years old, are adequately trained and supervised, and have read and understood the manual.

No, do not use the GLOBE GCB36G-RK outdoors.

Always turn off the GLOBE GCB36G-RK when not in use, when servicing, or adjusting any parts, and before cleaning.

Before operating the GLOBE GCB36G-RK, it should be checked to see that it is sitting level, feet should be adjusted if necessary, and the catch tray must be properly placed.

No, never bypass, alter, or modify the GLOBE GCB36G-RK in any way from its original condition, as doing so may create hazards and will void the warranty.

The controls of the GLOBE GCB36G-RK should be wiped down with a clean cloth daily.