EUFY POE CAM S4 EUFY T8E00 (01) PDF Document

Before mounting the EUFY POE CAM S4 EUFY T8E00, make sure your NVR is powered on and ready to connect to the camera.

The installation package for the EUFY POE CAM S4 EUFY T8E00 includes the following items:

• PoE Cam S4

• Positioning Sticker

• Screw Pack

• Mounting Bracket

• 18m Ethernet Cable

• Waterproof Cover Pack

You will need the following tools and devices to install the EUFY POE CAM S4 EUFY T8E00:

• Phillips Screwdriver

• Power Drill with 13/16″ (20.6 mm) & 1/4″ (6.3 mm) bits

• Hammer

• Ladder

The EUFY POE CAM S4 EUFY T8E00 camera consists of the following components:

• Mounting Base

• Spotlight

• Camera Lens

• LED Indicator

• Microphone

• Warning Light

• Speaker

• Spring Screw

• SD Card Slot

• SYNC/Reset Button

• Fusion Link Port

• DC Connector

• PoE Connector

The recommended location for mounting the EUFY POE CAM S4 EUFY T8E00 is as follows:

• Height of 2 m to 3 m (7 to 10 ft).

• A 20 m (65 ft) Field of View (for the Telephoto Lens).

• The camera can be installed on the ceiling or on a wall.

Follow these steps to prepare the mounting surface for your EUFY POE CAM S4 EUFY T8E00:

Step 1. Use the positioning sticker to mark the location for the cable hole and screw holes.

Step 2. Drill the cable hole using a 13/16″ (20.6 mm) drill bit.

Step 3. Drill the screw holes using a 1/4″ (6.3 mm) drill bit.

Step 4. Insert the provided anchors into the screw holes. If you are mounting on a wooden wall, you can skip this step.

Step 1. Install the Mounting Bracket: The bracket can be installed for either wall or ceiling mounting. Attach the side with 3 holes to the wall/ceiling using the provided screws.

Step 2. Insert the Camera: Place the EUFY POE CAM S4 EUFY T8E00 camera into the installed mounting bracket.

Step 3. Secure the Camera: Lock the spring screws to fasten the camera securely into the bracket.

Step 1. Connect the camera with the Ethernet cable.

Step 2. Ensure the Ethernet cable is connected to the NVR.

If the cable connector is exposed outside, follow these steps:

1. Route the cable through the cable notch.

2. Ensure the connector is positioned downward to prevent water intrusion.

3. Install the waterproof cover and connect the camera with the Ethernet cable.

4. Ensure the Ethernet cable is connected to the NVR.

To waterproof the cable connectors, follow these steps in order:

1. Ensure component A is pre-installed on the PoE connector of the camera.

2. Route the Ethernet cable through components B, C, and D.

3. Plug the Ethernet cable into the camera PoE connector.

4. Attach component D with the camera PoE connector, and twist to lock.

5. Insert component C into D, and rotate B to secure it to D.

Note: The shape of the waterproof cover and the connector may vary slightly.

Step 1. Remove the protective film from the camera lens.

Step 2. Rotate the camera to the optimal angle. After adjusting, check the live stream in the app.

• The recommended temperature range for T8E00 and accessories is -30°C to 45°C.

• Unless specifically indicated that it is safe to do so in the user guide or instruction manual, do not use the devices in an environment that exceeds the recommended low or high temperature.

• Unless specifically indicated that it is safe to do so in the user guide or instruction manual, avoid exposing your devices to direct sunshine or excessively wet environments.

• Do not use the product in any way other than described herein in order to avoid personal injury or property damage.

• Users should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes. Our company will not be responsible for any violators’ legal liability under any circumstances.