AXIS T90D20 POE IR-LED (01) PDF Document

The following hazard levels are used in the documentation for the AXIS T90D20 POE IR-LED:

DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: Indicates a situation which, if not avoided, could result in damage to property.

Please adhere to the following safety instructions for your AXIS T90D20 POE IR-LED:

Installation:

The Axis product shall be installed by a trained professional, and in compliance with local laws and regulations.

Eye Safety:

IR is emitted from this product. It can be harmful to the eyes. Avoid eye exposure. Use shielding or eye protection.

Possibly hazardous optical radiation is emitted from this product. It can be harmful to the eyes. Don’t stare at the operating lamp.

General Usage and Handling:

• The Axis product shall be used in compliance with local laws and regulations.

• Store the Axis product in a dry and ventilated environment.

• Avoid exposing the Axis product to shocks or heavy pressure.

• Do not install the product on unstable poles, brackets, surfaces or walls.

• Use only applicable tools when installing the Axis product. Using excessive force with power tools could cause damage to the product.

• Do not use chemicals, caustic agents, or aerosol cleaners.

• Use a clean cloth dampened with pure water for cleaning.

• Use only accessories that comply with the technical specification of your product. These can be provided by Axis or a third party. Axis recommends using Axis power source equipment compatible with your product.

• Use only spare parts provided by or recommended by Axis.

• Do not attempt to repair the product yourself. Contact Axis support or your Axis reseller for service matters.

Transportation:

When transporting the Axis product, use the original packaging or equivalent to prevent damage to the product.

The package for the AXIS T90D20 POE IR-LED contains the following items:

• AXIS T90D Illuminator (1x)

• Pre-mounted diversion lens

• Separate diversion lens (2x)

• IP66 cable coupler (for PoE versions only)

• Printed materials, including the Installation Guide

This guide describes an installation where the illuminator is controlled by the photocell.

1. If required, remove the screws and move the standard bracket to the top of the illuminator.

2. If required, loosen the screws and turn the bracket 90°.

3. Position the illuminator next to the camera and point the illuminator towards the camera’s field of view.

4. Connect the illuminator to the Power Source Equipment (PSE). For PoE versions like the AXIS T90D20 POE IR-LED, connect the network cables from the PSE and the illuminator to the IP66 cable coupler.

Important: To maintain the IP66 rating of the illuminator, make sure that the illuminator is correctly connected to the PSE.

CAUTION: Do not power the illuminator if the power cable is damaged. If done in a professional way, it is possible to shorten the power cable and replace the connector to repair the cable. If unable to repair the power cable, the illuminator must be disposed of and re-cycled.

Handle the lens with care and do not touch the optical film.

• The pre-mounted lens provides an angle of illumination of 35°.

• To alter to a 10° angle, remove the lens.

• To alter to a 60° angle, replace with the supplied lens.

• To alter to an 80° angle, replace with the supplied lens.

A lens for a 120° angle is available but not included with the product. All lenses have markings with the angle of illumination.

To change the lens, follow these steps:

1. Disconnect the power.

2. Remove the screws holding the baseplate using a 2.5 mm allen/hex key.

3. Change to a diversion lens with the desired angle of illumination.

4. Place the baseplate in its original position and fasten the screws using a 2.5 mm allen/hex key.

5. Point the illuminator towards the camera’s field of view.

Important: To maintain the IP66 rating of the illuminator, make sure that the illuminator is correctly reassembled.

The AXIS T90D20 POE IR-LED has two colored LED indicators on its base that provide operating and status information. On powering up, the illuminator automatically enters Programming Mode.

The LED indicator statuses are as follows:

• LHS LED solid green: Power on

• RHS LED flashing amber: Illuminator is in Programming Mode

• LHS LED solid red: Illuminator fault detected

• LHS LED flashing red: Voltage supply problem detected

Note: If any manual buttons are pressed, the illuminator automatically enters Normal Operating Mode 30 minutes after the last button press. After 7 days, the illuminator automatically enters Normal Operating Mode and the RHS LED is unlit.

The external power cable cannot be replaced. If it is damaged and you are unable to shorten and re-use the cable, the illuminator must not be powered. The illuminator is Class III for insulation.

Applies to PoE illuminators only: In order for the Power Supply Equipment (PSE) to conform to IEC/EN 60950-1, maximum power supplied to each illuminator must not exceed 60 W.

Applies to all illuminators: The LEDs (light source) of these illuminators are not replaceable. When the unit reaches its end of life, the whole illuminator shall be disposed of and re-cycled where possible.

To perform a full reset and restore the illuminator to its factory settings, follow these steps:

1. Press and hold the two manual control buttons whilst recycling the power.

2. Both Indicator LEDs will flash amber when the reset is completed.