EPSON LIFESTUDIO GRAND EH-LS670B (01) PDF Document

The manual for your EPSON LIFESTUDIO GRAND EH-LS670B uses various symbols to convey important information safely and effectively. Understanding these symbols is crucial for proper operation and to avoid injury or damage.

Safety Symbols:

• Warning: This symbol indicates information that, if ignored, could possibly result in personal injury or even death.
• Caution: This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

General Information Notations:

• Attention: This label indicates procedures that may result in damage or injury if sufficient care is not taken.
• Note Icon (Paper with folded corner): This label indicates additional information that may be useful to know.
• Button Symbol (Circle with text): Indicates the buttons on the remote control or the control panel.
• Menu/Setting name: Indicates projector menu and setting names. For example, Projector > Keystone > Zoom & Shift.
• Arrow Icon (»): This label indicates links to related pages.
• Menu Path Icon (s): This label indicates the projector’s current menu level.

A more detailed list of safety symbols found on the equipment is provided below:

To ensure the best performance and image quality from your EPSON LIFESTUDIO GRAND EH-LS670B, follow these placement guidelines:

1. Stable Surface: Place the projector on a sturdy and level surface, such as a table or low shelf.

2. Adjust Tilt: If the image is tilted, rotate the front adjustable feet to level the projector and make the image horizontally straight.

3. Ventilation: Leave plenty of space around and under the projector for proper ventilation. Do not place it on top of or next to anything that could block the air intake or exhaust vents.

4. Square to Screen: For the best quality images, place the projector so it squarely faces the screen, not at an angle. This minimizes keystone distortion. If you cannot place it squarely, you can use the projector’s controls to correct the distortion, but direct placement is recommended for optimal quality.

When installing your EPSON LIFESTUDIO GRAND EH-LS670B, adhere to the following precautions to ensure safety and proper functionality:

Environmental Precautions:

• Do not install in locations with high levels of dust, humidity, smoke, or steam to avoid fire or electric shock.
• Do not use or store in dusty or dirty locations, as this can degrade image quality or cause malfunctions.
• Avoid locations with potential salt damage or corrosive gases (like from hot springs) to prevent corrosion and malfunction.

Placement and Operation:

• Do not cover the air intake or exhaust vents, as this can cause the internal temperature to rise, leading to a fire.
• Do not install on an unstable surface or in a location that cannot support its weight, as it could fall and cause injury.
• Do not operate the projector on its side.
• Do not project images straight up or straight down.
• Do not tilt the projector to the right or left.

High Altitude Mode:

If you are using the projector at altitudes above 4,921 feet (1,500 m), you must set the High Altitude Mode to On. This ensures the projector’s internal temperature is regulated properly. You can find this setting in: Projector > Advanced Settings > High Altitude Mode.

Installation Space:

Be sure to leave the following minimum amount of space around the projector to avoid blocking the air exhaust and intake vents:

• Sides: 3.9 inches (10 cm)
• Rear: 11.8 inches (30 cm)

You can connect a video source with an HDMI port to your EPSON LIFESTUDIO GRAND EH-LS670B using an HDMI cable. This will send both video and audio to the projector.

Attention: Do not turn on the video source before connecting it to the projector, as doing so could cause damage.

1. Connect one end of the HDMI cable to your video source’s HDMI output port.

2. Connect the other end of the HDMI cable to one of the projector’s HDMI input ports (HDMI1, HDMI2, or HDMI3).

Important Notes:

• For gaming consoles, it is recommended to connect to HDMI1 or HDMI2, which support a 120 Hz refresh rate.
• When sending high-bandwidth signals like 4K 60 Hz 4:4:4, use a premium-high speed HDMI cable to ensure images are displayed correctly.
• Some devices output different signal types. Check your video device manual to confirm its output capabilities.

You can connect devices like a USB flash drive, digital camera, or USB hard drive to your EPSON LIFESTUDIO GRAND EH-LS670B to project images and other content.

1. If your USB device has its own power adapter, plug it into an electrical outlet.

2. Connect the USB device to the projector’s USB-A port.

3. Connect the other end of the cable to your device, if necessary.

Notes on USB Devices:

• The USB-A port is not guaranteed to operate all devices that support USB.
• You may need a specific app to project content from your USB device.
• USB hard drives should be USB Mass Storage Class-compliant, formatted in FAT16/32, and self-powered by their own AC power supplies (bus-powered drives are not recommended). Avoid using hard drives with multiple partitions.
• It is recommended to use a USB cable that is 9.8 feet (3 m) or less.

You can connect your EPSON LIFESTUDIO GRAND EH-LS670B to an external amplifier, speaker, or AV system in several ways.

Using an Optical Digital Audio Cable:

If your amplifier or speaker has an optical digital audio input port, follow these steps:

1. Connect one end of the optical digital audio cable to your audio device’s optical input port.

2. Connect the other end to the projector’s Optical Out port.

Note: If you set Audio Output Device to SPDIF in the projector’s menu, audio will only be output from the external device, not the projector’s speakers.

Using an eARC/ARC Compatible AV System (e.g., a sound bar):

If your AV system has an HDMI port that supports eARC or ARC, follow these steps:

1. Connect one end of an HDMI cable (with Ethernet) to your AV system’s HDMI output port (eARC or ARC compatible).

2. Connect the other end to the projector’s HDMI2 (eARC/ARC) port.

3. Make any necessary settings on the connected AV system. To enable this feature, you must also set Global CEC control to On in the projector’s menu (Channels & Inputs > Inputs > Global CEC control).

To listen to audio privately, you can connect headphones to your EPSON LIFESTUDIO GRAND EH-LS670B.

1. Connect your stereo headphone’s mini-jack cable to the projector’s Audio Out port.

Attention: The projector’s Audio Out port only supports 3-pin headphones. If you use other types of headphones, audio may not be output normally.

Caution: Do not start playback at a high volume setting, as sudden loud noises can cause hearing loss. Always lower the volume before powering off so you can gradually increase it after powering on.

The remote control for your EPSON LIFESTUDIO GRAND EH-LS670B uses two AAA batteries.

1. Remove the battery cover by sliding it off.

2. Remove the old batteries, if necessary. Please dispose of used batteries according to local regulations.

3. Insert the two new AAA batteries, ensuring the + and – ends align with the markings inside the battery holder. Warning: If batteries are not inserted correctly, they could explode or leak, causing fire, injury, or damage.

4. Replace the battery cover and press it down until it clicks into place.

When you turn on your EPSON LIFESTUDIO GRAND EH-LS670B for the first time, you need to complete the initial setup wizard.

1. Turn on the projector.

2. When the remote control pairing screen appears, press and hold the Home button and the Esc button on the remote at the same time to pair it with the projector. The indicator on the remote will flash during pairing and turn off when complete.

3. On the language selection screen, choose your desired language and follow the on-screen instructions to select your country or region.

4. Follow the on-screen instructions to make initial settings for the projector’s OS. It is recommended to log in with your Google Account for more detailed settings.

5. When the Wi-Fi setting screen is displayed, select your wireless network and follow the instructions to connect. An internet connection is required for online content.

6. Follow any remaining on-screen instructions for other necessary settings.

7. When you agree to the Epson license terms, the initial setup wizard closes, and the home screen is displayed.

Turning On the Projector:

1. Connect the power cord to the projector’s power inlet and plug it into a working electrical outlet. The projector will enter standby mode.

2. Press the power button on the projector or the remote control. The status indicator will turn white, and the projector will start up.

Warning: Never look directly into the projector lens when the light source is on. When turning on the projector with the remote, ensure no one is looking into the lens.

Turning Off the Projector (Suspended Mode):

This is the standard way to turn off the projector for daily use.

1. Press the power button on the projector or remote control.

2. The light source will turn off, the status indicator will turn off, and the projector will enter suspended mode.

Turning Off the Projector (Deep Standby Mode):

Use this mode to reduce power consumption when the projector is not in use for an extended period.

1. Hold down the power button on the remote control.

2. Select OK on the shutdown confirmation screen.

3. The projector will enter deep standby mode. Note that it will take longer for the projector to start up from this mode compared to suspended mode.

To transport or store the projector, make sure the status indicator is off, and then unplug the power cord.

If the projected image is blurry, you can adjust the focus using the focus lever.

1. Turn on the projector and display an image.

2. Open the focus lever cover on the side of the projector.

3. Move the focus lever up or down to adjust the focus until the image is sharp.

4. Close the focus lever cover.

If the projected image is curved or not rectangular (keystone distortion), you can correct it using the projector’s menus. After correction, the image may be slightly smaller.

1. Turn on the projector and display an image.

2. Press the Projector Settings button on the remote control to open the Projector menu.

3. Select Keystone.

4. Select Remote control.

5. Select whether you are projecting on a Wall or Projector screen.

When Projecting on a Wall:

1. On the screen asking “What is the shape of your projected image?”, select whether the edges are straight but not rectangular, or if the edges are distorted.

2. If the edges are distorted, a second screen will appear. Select which part of the image is distorted (e.g., “Top or bottom is not straight”, “Whole image is curved”).

3. Follow the on-screen instructions to select the correction points using the arrow buttons and adjust them until the image is rectangular.

4. When you are finished, select Finish.

When Projecting on a Screen:

1. Follow the on-screen instructions to move the projector until the projected image is larger than the screen frame.

2. Select Next. The four-point correction screen will be displayed.

3. Select the points you want to correct and adjust them to fit the screen.

4. If necessary, select Corner Adjustment to use an eight-point correction for finer adjustments.

5. When you are finished, select Finish.

You can adjust various image settings on your EPSON LIFESTUDIO GRAND EH-LS670B through the projector’s menus.

Adjusting Image Size and Position (Zoom & Shift):

1. Press the Projector Settings button on the remote control.

2. Select Zoom & Shift.

3. Use the left and right arrow buttons to adjust the image size (Zoom).

4. Press the [Enter] button to switch to Shift mode.

5. Use the arrow buttons to adjust the image position.

Adjusting Image Color (Preset Color Correction):

1. In the Projector menu, select Keystone.

2. Select Adjust color.

3. Select the color that is closest to the color of your projection surface (e.g., a colored wall) and select OK.

Changing the Image Aspect Ratio:

This setting is available only when the input source is HDMI.

1. Press the Settings button on the remote to open the dashboard.

2. Select the settings icon on the dashboard.

3. Go to Display & Sound > Screen.

4. Select one of the available aspect ratios (e.g., Full, Super Zoom, 4:3).

Changing the Color Mode (Picture Mode):

1. Press the Settings button on the remote to open the dashboard.

2. Select the settings icon on the dashboard.

3. Go to Display & Sound > Display > Picture Mode.

4. Select the color mode that best suits your content and viewing environment (Dynamic, Standard, Cinema, Natural).

You can use the internal speaker of your EPSON LIFESTUDIO GRAND EH-LS670B to play audio from a Bluetooth-enabled device like a smartphone or tablet.

1. Turn on the projector and display an image.

2. Press the Projector Settings button on the remote control.

3. Select Bluetooth Speaker Mode. The Bluetooth Speaker Mode screen is displayed.

4. On your audio device, enable Bluetooth and search for available devices.

5. Select the projector’s name from the list on your device. The projected image will turn off 10 seconds after the Bluetooth connection is established.

6. To exit Bluetooth Speaker Mode, press the Projector Settings button.

Note: There may be a delay in the audio output from any Bluetooth device. You can only connect one audio device via Bluetooth at a time.

With Google Cast, you can stream content from your favorite apps on your phone, tablet, or laptop to your EPSON LIFESTUDIO GRAND EH-LS670B.

1. Connect your device (phone, tablet, computer) to the same wireless network as the projector.

2. Open a Google Cast-enabled app on your device and press the Cast icon.

3. Select your projector from the list of available devices.

The app will connect and begin casting to the projector.

4. To stop casting, press the Cast icon in the app and choose the disconnect option.

HDMI CEC allows you to use the projector’s remote to control certain features of a linked, CEC-compatible device (like a Blu-ray player or AV receiver).

1. Press the Settings button on the remote to open the dashboard.

2. Select the settings icon on the dashboard.

3. Select the menus in the following order: Channels & Inputs > Inputs > Global CEC control.

4. Set Global CEC control to On.

5. Adjust the following settings as necessary:

• Allow TV to turn off connected devices: Set to On to automatically turn off the connected device when you turn off the projector.
• Allow connected devices to turn on TV: Set to On to automatically turn on the projector when you turn on the connected device.

Once enabled, you can use the projector’s remote to control functions like playback, stop, or volume on the linked device.

You can get the latest projector firmware by using the Epson Projector Update application.

1. Press the Home button on the remote control.

2. Select Apps from the top of the home screen.

3. Start the Epson Projector Update app by selecting it from the apps list.

4. Follow the on-screen instructions to update the firmware.

Attention: While the firmware is updating, do not operate or turn off the projector.

Note: If the Epson Projector Update app is not installed, you can search for and install it from the Apps screen. If there is not enough space in the internal storage for the update, you may need to delete unnecessary apps and caches first.

You can reset all projector settings to their original default values. Be aware that this will delete all information, including installed apps, Google Account login information, and your custom menu settings.

1. Turn on the projector and display an image.

2. Press the Settings button on the remote control to open the dashboard.

3. Select the settings icon on the dashboard.

4. Select the menus in the following order: System > About > Reset > Factory reset.

5. Follow the on-screen instructions to start initializing the projector.

Regular cleaning helps maintain your EPSON LIFESTUDIO GRAND EH-LS670B’s performance and appearance. Warning: Before cleaning any part of the projector, turn it off and unplug the power cord.

Cleaning the Projection Window:

• If dusty, use a blower to blow off dust, then gently wipe the window with clean, dry lens-cleaning paper.
• To remove smudges, gently wipe with lens-cleaning paper.
• Attention: Do not wipe the window right after turning off the projector, as it may be hot. Do not use harsh materials or subject the window to impacts.

Cleaning the Motion Sensor:

• To remove dust or smudges, gently wipe the sensors with lens-cleaning paper.
• Warning: Do not use a lens cleaner that contains flammable gas.
• Attention: Do not use glass cleaner or harsh materials.

Cleaning the Projector Case:

• Use a soft, dry, lint-free cloth to remove dust.
• For stubborn dirt, use a soft cloth lightly moistened with water and mild soap. Do not spray liquid directly on the projector.
• Attention: Do not use wax, alcohol, benzene, paint thinner, or other chemicals.

Cleaning the Air Intake Vents:

Clean the vents on the base of the projector periodically to prevent overheating.

1. Turn off the projector and unplug the power cord.

2. Turn the projector upside down.

3. Carefully remove dust from the vents using a vacuum cleaner or a soft brush.

Regular filter maintenance is important to prevent overheating. Clean the filter when a message appears or if you notice it is dusty. Replace the filter if it is torn or damaged.

Cleaning the Air Filter:

1. Turn off the projector and unplug the power cord.

2. On the side of the projector, slide the air filter cover latch and pull out the air filter cover.

3. Pull the air filter out of the air filter cover.

4. Vacuum the front of the air filter (the side with the tabs) to remove dust. Attention: Do not rinse the filter in water or use any detergent or solvent. Do not use canned air.

5. Place the filter back into the cover with the four tabs facing down.

6. Re-insert the air filter cover and close it until it clicks into place.

Replacing the Air Filter (Model: ELPAF60):

1. Turn off the projector and unplug the power cord.

2. Open the air filter cover as described above.

3. Pull the old air filter out of the projector and dispose of it according to local regulations.

4. Place the new air filter with the four tabs facing down as shown in the manual.

5. Close the air filter cover until it clicks into place.

The status indicator provides information about the projector’s condition. Refer to the table below for solutions.

If your EPSON LIFESTUDIO GRAND EH-LS670B does not turn on when you press the power button, follow these troubleshooting steps:

1. Make sure the power cord is securely connected to both the projector and a working electrical outlet.

2. If you are using the remote control, check the batteries. They may need to be replaced.

3. The power cord itself may be defective. If possible, try a different power cord. If the problem persists, disconnect the cord and contact Epson for help.

If the light source on your EPSON LIFESTUDIO GRAND EH-LS670B turns off unexpectedly, check the following possible causes:

1. Shut-Off Timer: The projector may have turned off due to the Shut-Off Timer setting in the System > Power & Energy menu. Press the power button to turn it back on.

2. No Signal Standby Timeout: If you switched to an HDMI source and there was no input signal for a set period, the projector may have automatically entered standby mode. Press the power button to wake it. This setting is in Channels & Inputs > Inputs > [HDMI Source] > No signal standby timeout.

3. Overheating: If the status indicator is lit orange, the projector has overheated. Let it cool down and check for blocked vents or a dirty air filter.

4. Obstruction: Ensure that nothing is blocking the projection window. Remove any obstacles.

If no image is displayed, try these steps to solve the problem:

1. Check Projector Status: Look at the status indicator to confirm it is in normal operating status (lit white). If it’s off, press the power button to wake it from standby mode.

2. Check Cable Connections:

• Ensure all cables are securely connected to both the projector and the video source.
• Try connecting the video source directly to the projector, bypassing any AV receivers or switches.
• Replace the HDMI cable with a shorter one (16.4 feet / 5 m or less is recommended).

3. Check Video Source:

• Turn on the connected video source and press its play button if necessary.
• If projecting from a laptop, make sure it is set to display on an external monitor.

4. Check Other Items:

• Turn off the projector and the connected video source, then turn them back on.
• Make sure your computer’s display resolution does not exceed the projector’s limits.
• As a last resort, reset all of the projector’s settings to their default values.

For a Fuzzy or Blurry Image:

1. Adjust the image focus using the focus lever on the side of the projector.

2. Position the projector closer to the screen if it is too far away.

3. Clean the projection window with lens-cleaning paper.

4. Adjust the Sharpness setting in the Display & Sound > Display menu.

5. If projecting from a computer, try selecting a lower display resolution that matches the projector’s native resolution.

For a Partial Image:

1. Adjust the position of the projected image using the Zoom & Shift setting in the Projector menu.

2. Select an appropriate aspect ratio from the Display & Sound > Screen menu (for HDMI sources).

3. Check your computer’s display settings to ensure dual display is disabled and the resolution is within the projector’s limits.

For an Image with Incorrect Brightness or Colors:

1. Try different Color Modes (Picture Modes) in the Display & Sound > Display > Picture Mode menu to see which one looks best.

2. Check the video settings on your source device.

3. Manually adjust color settings like Brightness, Contrast, and Saturation in the Display & Sound > Display menu.

4. Ensure all video cables are securely connected. Try shorter cables if you are using long ones.

5. Position the projector closer to the screen.

For an Image that Contains Noise or Static:

1. Check the video cables. They should be securely connected at both ends and separated from the power cord to prevent interference.

2. Adjust the DNR (Digital Noise Reduction) setting in Display & Sound > Display > Advanced Settings.

3. If you used digital image correction (like Keystone), try decreasing the Sharpness setting to improve quality.

4. If you connected an A/V system that does not support eARC/ARC to the HDMI port, the image may be distorted.

If you are having audio problems with your EPSON LIFESTUDIO GRAND EH-LS670B, follow these troubleshooting steps:

1. Press the volume up button on the remote control to increase the projector’s volume.

2. Check the cable connection between the projector and your video source.

3. Check your video source to make sure its volume is turned up and its audio output is set to the correct source.

4. If you want audio from the projector’s speakers: Check that Global CEC control is set to Off in the Channels & Inputs > Inputs menu.

5. If you want to output audio to an external device via HDMI eARC/ARC:

• Set Global CEC control to On in the projector’s menu.
• Make sure your HDMI cable is compliant with HDMI eARC and ARC.
• If audio is still not outputting correctly, try changing the Digital Output setting from Auto to PCM in the Display & Sound > Audio Output menu.

6. If you want audio ONLY from a device connected to the Optical Out port: Set Audio Output Device to SPDIF in the Display & Sound > Audio Output menu. This will disable the projector’s internal speakers.

If the projector does not respond to remote control commands, try the following solutions:

1. Check that the batteries are installed correctly and have power. If necessary, replace the batteries.

2. Ensure no buttons on the remote are stuck down. Press them to return them to their normal positions.

3. If the pairing screen is displayed on the projector, the remote may need to be paired again. Press and hold the Home button and Esc button at the same time for about three seconds to re-pair.

4. Make sure you are operating the remote within the reception angle and range of the projector (up to 19.7 feet or 6 m).

5. Strong fluorescent lighting, direct sunlight, or other infrared device signals can interfere with the remote receivers. Dim the lights or move the projector away from the source of interference.

6. If none of these steps work, the remote control may be defective. Contact Epson for help.

If you cannot connect your EPSON LIFESTUDIO GRAND EH-LS670B to a Wi-Fi network, try the following solutions:

1. Make sure your Wi-Fi router and modem are working properly. Rebooting these devices (turning them off and on again) may solve the connection problem.

2. Check for obstacles between the Wi-Fi router and the projector. Move them closer together or remove obstructions to improve communication.

3. You can check the network settings from the Wi-Fi section in the Network & Internet menu.

4. If you have recently initialized (factory reset) the projector, you will need to select and set up the network again on the initial setup screen.