DJI OSMO MOBILE 7 (03) PDF MANUAL

The product is fully charged when the Battery Level Indicator turns off.

Unfold the gimbal as shown in the illustrations in the PDF.

The built-in tripod is suitable for stable, level surfaces in windless environments. In other conditions, it is recommended to attach DJI OM Grip Tripod (sold separately) to the bottom of the gimbal.

Only Osmo Mobile 7P has a built-in extension rod.

If you extend the built-in extension rod, make sure to adjust the Pan Motor to be level with the ground. This ensures balance after the phone is attached to the gimbal.

A steady gimbal mode light (represented by icons for Pan and Tilt Follow, Pan Follow, FPV, SpinShot) indicates that the gimbal is stabilizing the phone. If the light is not displayed after you attach the phone, press the M button to enable stabilization.

1. Enable Bluetooth on your phone, open DJI Mimo, and connect to the gimbal.

If Bluetooth connection fails, try the following steps:

1. Go to Bluetooth settings on your phone. Remove any existing connections with the gimbal and forget the device.

2. Reset Bluetooth for the gimbal.

3. Tap the new device name in Bluetooth settings. Once connected, relaunch DJI Mimo.

A prompt will appear in DJI Mimo when new firmware is available. Tap the prompt and follow the on-screen instructions to update the firmware.

Ensure that the Battery Level Indicator shows solid green before the update. DO NOT exit DJI Mimo during the update.

If the update fails, restart DJI Mimo, reestablish the Bluetooth connection, and retry.

Grip gestures apply to both landscape and portrait orientations.

Only Osmo Mobile 7P has a built-in extension rod.

If the built-in tripod is extended, grip the handle to ensure stability. Do NOT grip only the tripod.

When powered off

With the gimbal folded, press once: Check the battery level

With the gimbal unfolded, press once: Power on

When powered on

Press once: Switch between gimbal modes

Press three times: Enter standby mode (press any button to exit)

Press and hold: Power off

The M button can also control phone charging using the gimbal or Multifunctional Module.

Press once: Switch between focus and zoom

Rotate: Control focus or zoom

The side wheel can control the fill light when used with Multifunctional Module.

Push once: Switch between preset zoom levels

Push continuously: Change zoom continuously

Move vertically and horizontally to tilt and pan the mobile phone. The joystick control direction can be set in DJI Mimo.

Press once: Take a photo or start/stop recording

Press twice: Take a photo during recording

Press and hold: Burst shooting when in photo mode

Press once: Switch between front and rear cameras

Press twice: Switch between landscape and portrait modes

Press three times: Switch between photo and video modes

Press once: Start or stop ActiveTrack

Press twice: Recenter the gimbal

Press three times: Rotate the phone 180 degrees in the horizontal plane

Press once, and then press and hold: Adjust the follow speed to fast mode. Release to exit.

Press and hold: Enter lock mode. Release to exit.

Connect a USB-C cable to the charging port on the gimbal to charge it.

Press the switch button, shutter/record button, and trigger simultaneously for more than one second to reset the Bluetooth name and connection and reconnect.

Make sure that the gimbal is sufficiently charged (the indicator shows solid yellow or solid green).

Make sure that the gimbal is powered off.

Certain phones are charged only after pressing the M button.

For Osmo Mobile 7P, retract the extension rod before performing the following steps.

When the gimbal powers off, it automatically rotates to the folding position. Remove the phone, phone clamp, and Multifunctional Module together. For the next use, attach them as a whole and unfold the gimbal to start shooting.

The Osmo Mobile 7P combo includes Multifunctional Module and accompanying accessories. For Osmo Mobile 7, the module and accessories are sold separately.

If the indicator does not turn on after Multifunctional Module is installed, check whether the marks on the gimbal and the phone clamp are aligned.

If Multifunctional Module is idle for more than five minutes, it automatically enters sleep mode and the indicator turns off. To exit sleep mode, press the trigger on the gimbal.

Avoid blocking the rear camera when shooting in landscape mode by correctly positioning the module.

Multifunctional Module allows you to enable tracking in the system camera and third-party camera apps, without the need to use DJI Mimo.

Multifunctional Module supports tracking people only.

The tracking and shooting features of Multifunctional Module are disabled in DJI Mimo.

Position the tracking camera of Multifunctional Module and the phone camera towards the subject. For example, both cameras can be used to take selfies.

To achieve optimal gesture recognition, keep the subject 0.5m to 3m away from the tracking camera.

During tracking, keep the subject 0.5m to 8m away from the tracking camera.

1. Enable Bluetooth on the phone and connect to the gimbal.

2. Enable tracking: Show the open palm gesture to the camera or press the trigger. The indicator turns solid green.

3. Adjust the composition as needed during tracking.

Show the OK gesture to the camera. The indicator turns solid yellow and tracking is automatically paused. The subject can move to the desired position in the frame.

Show the OK gesture again to confirm the composition. The indicator turns solid green and tracking automatically resumes.

To restore the default composition for each method, press the trigger twice.

Stop tracking: Show the open palm gesture or press the trigger again. The indicator turns solid red.

Whether tracking is enabled or not, you can use the V-sign gesture to start a countdown for taking a photo or starting/stopping recording. The indicator pulses yellow during the countdown.

Make sure that Multifunctional Module is properly installed. Press the brightness control button once to adjust the brightness.

Make sure that Multifunctional Module is properly installed. Press the color temperature control/Bluetooth pairing button once to adjust the color temperature.

Press and hold: Turn on/off the fill light

Rotate: Adjust brightness or color temperature

Press once: Switch between controlling brightness and color temperature

Press twice in DJI Mimo: Set the effect of rotating the side wheel to focus/zoom control or brightness/color temperature control

Multifunctional Module can connect to two wireless microphone transmitters. The two transmitters must be the same model. Supported transmitters are DJI Mic Mini and DJI Mic 2.

1. Connect Multifunctional Module to the phone.

2. Enable Bluetooth pairing for Multifunctional Module.

3. Power on the transmitter and set linking mode. For DJI Mic Mini, use linking mode with the receiver. For DJI Mic 2, use linking mode via Bluetooth.

4. Once linked, the indicator of Multifunctional Module turns solid green. The indicator of the transmitter switches to the linked status in the corresponding mode. You can start recording.

To prevent the cable connecting Multifunctional Module and the phone from obstructing the gimbal, bend the cable as needed. Make sure to use the cable included in the package.

For iPhone 14 and earlier models, a USB-C to Lightning cable (sold separately) is required to connect to Multifunctional Module.

You can configure wireless microphone settings in DJI Mimo. This feature applies to DJI Mic Mini only.

Make sure that Multifunctional Module is properly installed.

When using DJI Mimo to update the gimbal firmware, the module firmware is updated together. Please wait for the upgrade to complete.

You can use DJI Mimo on an Apple Watch to view the camera feed, control the gimbal, and enable ActiveTrack remotely.

1. Pair the watch with your phone and install DJI Mimo on both devices.

2. Run DJI Mimo on the phone, connect to the gimbal, and enter the camera view.

3. Run DJI Mimo on the watch to start remote control.

Keep the devices within the Bluetooth range.

Put out any product fire using water, sand, fire blanket, or a dry powder fire extinguisher.

Never disassemble or pierce the product in any way or the battery may leak, catch fire, or explode.

It is recommended to use a soft, dry cloth to clean the product.

When the phone is attached to the gimbal, the compass feature of the phone may experience interference. In such cases, calibrate the compass according to the prompts in the phone.

The NFC (near-field communication) and wireless charging functions of the phone may be affected when the phone clamp is attached. These functions will no longer be affected once the phone clamp has been removed from the phone.

The built-in extension rod contains a spring. If the extension rod is extended for more than a week, the spring may become deformed and the extension rod can no longer be used normally. It is recommended to retract the extension rod and fold the gimbal after use.

Only Osmo Mobile 7P has a built-in extension rod.