BOSCH FLEXIDOME MICRO 3100I NUV-3703-F06-GOV (01) PDF Document

The recommendations for the computer system are:

– Computer with Dual core HyperThreading processor or better

– Graphic card with performance that matches or is better than the resolution of the camera

– Windows 10 or later

– Network access

– Google Chrome, Microsoft Edge, or Mozilla Firefox

– or – Application software, for example, Video Security Client, Bosch Video Client or BVMS.

The unit must have a valid IP address and a compatible subnet mask to operate on your network. By default, DHCP is pre-set at the factory to On and so your DHCP server assigns an IP address. With no DHCP server the default address is automatically assigned via link-local address.

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before the device can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The device is password-protected. The first time that any user accesses the device, the device will prompt the user to set a password at the service level. Make sure the password obeys these conditions:

– 8 to 19 characters in length

– Upper and lower case letters

– Minimum of 1 digit

– Minimum of 1 special character

These special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’

A factory default deletes all camera settings including passwords, network settings, and image settings. Complete the following sequence of steps only if you have no other option to restore operation to the camera.

1. Apply power to the camera.

2. Find the hardware reset button on the camera block. Remove the camera bubble to access the reset button.

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing to show that the hardware reset started.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address. Access the camera using the web browser. Set the initial password for the camera.

On the left side of the browser within the Playback page, expand the Export group if necessary:

1. Select a track in the track list or in the search results.

2. The start and stop date and time are filled for the selected track. If necessary, change the times.

3. In the Time lapse drop-down box, select Original, to export the recorded video as its original, or Condensed to export the recorded video condensed to the given output time.

4. In the Location drop-down box, select a target.

5. Click Export to save the video track.

The target server address is set on the Connectivity > Accounts page.

To create a new user, navigate to Configuration > General > User Management and click Add in the section below Authentication modes. In the box User, fill in the fields:

1. User name: Enter a name with a minimum of 5 and a maximum of 31 characters.

2. Group: Select the appropriate authorization level (live, user, IVA configuration, or service).

3. Type: Select either Password (enter a new password twice) or Certificate.

4. Click Set to confirm and create a new user.

Navigate to Configuration > General > Date/Time. Make sure that recording is stopped before synching to the PC.

1. Enter the current date. Since the unit time is controlled by the internal clock, there is no need to enter the day of the week – it is added automatically.

2. Enter the current time or click the Sync to PC button to copy your computer’s system time to the camera.

Navigate to Configuration > Camera > Installer Menu.

Image rotation: Select the option that best suits the device mounting position:

– 0°

– 90° – upright

– 180°

– 270° – upright

The upright modes (90° and 270°) are good for vertical scenes, such as hallways or perimeters. When these options are selected, the aspect ratio and the signaling to the interfaces change (example, 16:9 to 9:16).

Mirror image: Select On to output a mirror image of the device picture.

There are two options available in Configuration > Camera > Installer Menu:

Restore settings: Click Restore to restore all settings, except network settings, to their defaults.

Factory defaults: Click Defaults to restore all settings, including passwords and network settings, to their defaults.

Note: Clicking these buttons also clears the service-level password. Operators must reset the password before doing anything else.

Privacy Masks block specific areas of a scene from being seen in the camera’s field of view. To configure a Privacy mask:

1. Navigate to Configuration > Camera > Privacy Masks.

2. Select the mask number from the drop-down list.

3. Click the plus button.

4. Adjust the mask in the image: Double-click on the edges to add or remove nodes. Click and drag the nodes to position them correctly.

5. Check the Enabled check box to activate the related mask.

6. Click the Set button to apply the related changes.

Formatting the storage media can be necessary to delete all data and recreate a valid file structure to be usable. All recordings on a storage medium can be deleted at any time.

1. Navigate to Configuration > Recording > Storage Management.

2. Click a storage medium in the Managed storage media list to select it.

3. Click Edit below the list.

4. Click Format in the new window to delete all recordings in the storage medium.

5. Click OK to close the window.

6. Click Set to apply the changes.

To update the firmware, navigate to Configuration > Service > Maintenance.

1. First, store the firmware file on your hard disk.

2. Enter the full path for the firmware file in the field or click Browse… to locate and select the file.

3. Click Upload to begin transferring the file to the device. The progress bar allows monitoring of the transfer.

The new firmware is unpacked and the Flash memory is reprogrammed. The time remaining is shown by the message going to reset Reconnecting in … seconds. When the upload is completed successfully, the device reboots automatically.

Notice! Before starting a firmware update, make sure to select the correct upload file. Do not interrupt the firmware installation.

Navigate to Configuration > Alarm > Alarm Email.

1. Send alarm e-mail: Select On for the device to automatically send an alarm e-mail in the event of an alarm.

2. Mail server IP address: Enter the IP address of a mail server that operates on the SMTP standard. Otherwise, leave the box blank (0.0.0.0).

3. SMTP port: Select the appropriate SMTP port.

4. SMTP user name: Enter a registered user name for the chosen mail server.

5. SMTP password: Enter the required password for the registered user name.

6. Format: Select the data format (Standard with JPEG or SMS).

7. Destination address: Enter the e-mail address for alarm e-mails here.

8. Sender address: Enter a unique name for the e-mail sender.

9. Click Set to apply the changes.

In Configuration > Camera > Installer Menu:

– Click the Enabled or Disabled check-box to switch the Camera LED on or off.

– Select Auto disable to let the camera determine when the LED should be switched off. The camera LED activates when powering on the camera for the first time. The LED deactivates automatically after 5 minutes.

Navigate to Configuration > Network > Network Access.

If the network has a DHCP server for the dynamic assignment of IP addresses, select On for Automatic assignment (DHCP). To assign a static IP:

1. Enter the desired IP address for the camera. The IP address must be valid for the network.

2. Enter the appropriate subnet mask for the set IP address.

3. Enter the IP address of the gateway if required.

4. Click Set and Reboot. The device is rebooted and the changed settings are activated.