BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04 (01) PDF Document

To ensure safe operation of the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04, please adhere to the following instructions:

To clean the device, do not use liquid cleaners or aerosol cleaners.

Do not install the device near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat.

Do not spill liquids on the device before installation is completed.

Take precautions to protect the device from power and lightning surges.

Adjust only those controls specified in the operating instructions.

Operate the device only from the type of power source indicated on the label.

Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing to qualified service personnel.

Optical elements are sensitive and should be protected at all times. Do not allow objects to come into contact with glass surfaces and do not touch optical elements with your fingers.

The recommended system requirements for the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04 are:

Computer with Dual core HyperThreading processor or better.

Graphic card with performance that matches or is better than the resolution of the camera.

Windows 10 or later.

Network access.

Google Chrome, Microsoft Edge, or Mozilla Firefox.

Alternatively, Application software such as Video Security Client, Bosch Video Client, or BVMS can be used.

To connect to the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04, follow these steps:

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before the device can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04 requires a strong password. The password must obey the following conditions:

8 to 19 characters in length.

Upper and lower case letters.

Minimum of 1 digit.

Minimum of 1 special character.

Note: The following special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’.

To create a new user via the User Management configuration:

1. Click Add in the section below Authentication modes.

2. In the box User, fill in the User name (minimum 5, maximum 31 characters).

3. Select the appropriate Group (authorization level): live, user, IVA configuration, or service.

4. Select either Password (to set a new password) or Certificate (for a certificate the user is authorized to use).

5. Click Set to confirm and create a new user.

To export video from the Playback page:

1. Expand the Export group on the left side of the browser if necessary.

2. Select a track in the track list or in the search results.

3. The start and stop date and time are filled for the selected track. If necessary, change the times.

4. In the Time lapse drop-down box, select Original (to export original video) or Condensed (to export video condensed to a given output time).

5. In the Location drop-down box, select a target.

6. Click Export to save the video track.

To synchronize the internal clock of the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04 with your computer:

1. Ensure recording is stopped.

2. Navigate to Configuration > General > Date/Time.

3. Enter the current time or click the Sync to PC button to copy your computer’s system time to the camera.

4. Click Set to save the changes.

In the Installer Menu (Configuration > Camera > Installer Menu):

Sensor mode: Adjust the base resolution and frame rates (e.g., 25 fps for 50 Hz, 30 fps for 60 Hz).

Image rotation: Select one of the four options:

– 0° (Normal position)

– 90° – upright

– 180°

– 270° – upright

Mirror image: Select On to output a mirror image of the device picture.

To calibrate the camera using sketch-based tools:

1. Navigate to Configuration > Camera > Positioning.

2. Enter any known values for tilt angle, roll angle, height, and focal length.

3. For unknown values, select the Calculate check box.

4. Place calibration elements on the camera image:

– Click the vertical line icon to place a vertical line across the image (e.g., a door frame or lamp post).

– Click the ground line icon to place a line across the ground in the image (e.g., a road marking).

– Click the angle icon to place an angle on the ground (e.g., corner of a parking bay).

5. Adjust the elements: Select the line or angle and enter its real size in the corresponding box. Drag the line or angle to position it correctly on the image.

6. Blue lines indicate elements you added; white lines represent the element as it should be positioned based on current calibration results.

The White Balance modes available in the Color configuration page are:

To configure a Privacy Mask:

1. Navigate to Configuration > Camera > Privacy Masks.

2. Select the mask number from the drop-down list.

3. Click the plus button.

4. Adjust the mask in the image by double-clicking on edges to add or remove nodes, and dragging nodes to position them.

5. Check the Enabled check box to activate the related mask.

6. Select the color (Auto, Black, Gray, White, or Custom color).

7. Click the Set button to apply the changes.

To use the Pixel Counter for measuring objects in the image:

1. Navigate to Configuration > Camera > Pixel Counter.

2. Click Freeze to freeze the camera image if the object you want to measure is moving.

3. To reposition a zone, place the cursor over the zone, hold down the mouse button and drag into position.

4. To change the shape of a zone, place the cursor over the edge of the zone, hold down the mouse button and drag the edge to the required position.

5. The number of horizontal and vertical pixels covered by the highlighted area is displayed below the picture.

To configure iSCSI media:

1. Navigate to Configuration > Recording > Storage Management > iSCSI Media.

2. Enter the IP address of the iSCSI destination in the iSCSI IP address field.

3. If password protected, enter the password in the Password field.

4. Click Read to establish the connection.

5. In the Storage overview section, double-click an iSCSI LUN.

6. Click Set to activate the media in the Managed storage media list. The status should show as Online.

7. Check the box in the Rec. 1 or Rec. 2 column to specify the recording tracks.

To format storage media and recreate a valid file structure:

1. Navigate to Configuration > Recording > Storage Management.

2. Click a storage medium in the Managed storage media list to select it.

3. Click Edit below the list.

4. Click Format in the new window to delete all recordings.

5. Click OK to close the window.

6. Click Set to apply the changes.

The default recording profiles for Video Channel 1 (Full image Circle) include:

To configure the Recording Scheduler:

1. Navigate to Configuration > Recording > Recording Scheduler.

2. Click the profile to be assigned in the Time periods box.

3. Click a field in the table and, while holding down the left mouse button, drag the cursor across all of the fields to be assigned to the selected profile (in 15-minute intervals).

4. Use Select All to assign the selected profile to all intervals, or Clear All to deselect.

5. Click Set to save the settings.

6. To activate, click Start.

To configure the camera to send alarm emails:

1. Navigate to Configuration > Alarm > Alarm Email.

2. Select On for Send alarm e-mail.

3. Enter the Mail server IP address (SMTP standard).

4. Select the appropriate SMTP port.

5. Enter the SMTP user name and SMTP password if authentication is required.

6. Select the Format (Standard with JPEG or SMS).

7. Enter the Destination address and Sender address.

8. Click Set to apply changes.

9. Click Send Now to test the function.

To update the firmware via the Maintenance page:

1. Store the firmware file on your hard disk.

2. Navigate to Configuration > Service > Maintenance.

3. In the Firmware section, click Browse… to locate and select the file.

4. Click Upload to begin transferring the file.

5. The device will reboot automatically when the upload is completed successfully.

Notice: Do not interrupt the firmware installation.

If you cannot access the camera or need to restore factory defaults, follow these steps:

1. Apply power to the camera.

2. Remove the camera bubble to access the reset button.

3. Find the hardware reset button on the camera block.

4. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing.

5. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

6. Search again for the IP address and access the camera using the web browser to set the initial password.