BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV (01) PDF Document

To clean the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV, do not use liquid cleaners or aerosol cleaners.

Do not install the device near any heat sources such as radiators, heaters, stoves, or other equipment (including amplifiers) that produce heat.

Do not spill liquids on the device before installation is completed.

Take precautions to protect the device from power and lightning surges.

Adjust only those controls specified in the operating instructions.

Operate the device only from the type of power source indicated on the label.

Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing to qualified service personnel.

The recommendations for the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV are:

Computer with Dual core HyperThreading processor or better.

Graphic card with performance that matches or is better than the resolution of the camera.

Windows 10 or later.

Network access.

Google Chrome, Microsoft Edge, or Mozilla Firefox.

Alternatively, application software such as Video Security Client, Bosch Video Client, or BVMS can be used.

The unit must have a valid IP address and a compatible subnet mask to operate on your network. By default, DHCP is pre-set at the factory to On.

1. Start the web browser.

2. Enter the IP address of the device as the URL.

3. During the initial installation, confirm any security questions that show.

If a RADIUS server is used for network access control (802.1x authentication), you must configure the device before the device can communicate with the network. To configure the device, connect it directly to a computer using a network cable and then set the service-level password.

The BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV requires a strong password. The password must obey these conditions:

8 to 19 characters in length.

Upper and lower case letters.

Minimum of 1 digit.

Minimum of 1 special character.

The following special characters are not allowed: ‘@’, ‘&’, ‘<', '>‘, ‘:’, ‘+’

After the connection is established to the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV, the Live page is initially displayed. To view a live stream:

1. On the left side of the browser, expand the Connection group if necessary.

2. Click the Stream drop-down arrow to see the options.

3. Select the stream you wish to view.

On the Playback page of the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV interface:

1. Expand the Export group on the left side of the browser if necessary.

2. Select a track in the track list or in the search results.

3. The start and stop date and time are filled for the selected track. If necessary, change the times.

4. In the Time lapse drop-down box, select Original to export the recorded video as its original, or Condensed to export the recorded video condensed to the given output time.

5. In the Location drop-down box, select a target.

6. Click Export to save the video track.

To create a new user on the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV:

1. Go to Configuration > General > User Management and click Add in the section below Authentication modes.

2. In the box User, fill in the User name (minimum 5, maximum 31 characters).

3. Select the appropriate authorization level in the Group field (live, user, IVA configuration, or service).

4. In the Type field, select either Password (enter a new password twice) or Certificate.

5. Click Set to confirm and create a new user.

To edit a password, click the pencil icon to the right of the column Type for the appropriate User name.

Navigate to Configuration > General > Date/Time. Make sure that recording is stopped before synching to the PC.

1. Enter the current date.

2. Enter the current time or click the Sync to PC button to copy your computer’s system time to the camera.

Alternatively, you can configure a Time server address to receive the time signal automatically.

Go to Configuration > Camera > Installer Menu.

For Image rotation, select one of the following options:

– 0 degrees

– 90 degrees – upright

– 180 degrees

– 270 degrees – upright

For Mirror image, select On to output a mirror image of the device picture. The end result is shown in the Live preview.

Go to Configuration > Camera > Display Stamping.

You can configure various overlays such as Camera name stamping, Time stamping, Logo stamping, and Alarm mode stamping.

For each item, you can generally configure:

– Position (Top, Bottom, Custom, or Off)

– Stamping size (Normal, Large, or Custom)

– Text color

– Background color

– Transparent background option

Click Set to apply the changes.

To determine non-automatically set values using Sketch-based calibration:

1. Enter the value for tilt angle, roll angle, height and focal length if the value is known.

2. For each value that is still unknown, select the Calculate check box.

3. Place a calibration element on the camera image:

– Click the vertical line icon to place a vertical line across the image (perpendicular to the ground plane, e.g., door frame).

– Click the line on ground icon to place a line across the ground in the image (on the ground plane, e.g., road marking).

– Click the angle on ground icon to place an angle on the ground in the image.

4. Adjust the calibration elements:

– Enter the real size of a line or angle in the corresponding box.

– Drag the line or angle or move the end points to the desired position in the camera image.

To configure a Privacy mask on the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV:

1. Go to Configuration > Camera > Privacy Masks.

2. Select the mask number from the drop-down list.

3. Click the plus button.

4. Adjust the mask in the image by double-clicking edges to add/remove nodes and dragging nodes to position them.

5. Check the Enabled check box to activate the related mask.

6. Click the Set button to apply the related changes.

You can also select the color (Auto, Black, Gray, White, or Custom color).

1. Go to Configuration > Recording > Storage Management.

2. Click a storage medium in the Managed storage media list to select it.

3. Click Edit below the list.

4. Click Format in the new window to delete all recordings in the storage medium.

5. Click OK to close the window.

6. Click Set to apply the changes.

Go to Configuration > Alarm > Alarm Email.

1. Select On for Send alarm e-mail.

2. Enter the IP address of the mail server in the Mail server IP address field.

3. Select the appropriate SMTP port.

4. Enter a registered SMTP user name and password.

5. Select the Format (Standard with JPEG or SMS).

6. Enter the Destination address (recipient email) and Sender address.

7. Click Set to apply the changes.

Go to Configuration > Network > Network Access.

If the network has a DHCP server, select On for Automatic assignment (DHCP).

To assign a static IP address:

1. Enter the desired IP address for the camera.

2. Enter the appropriate Subnet mask.

3. Enter the Gateway address if connecting to a remote location in a different subnet.

4. Click Set and Reboot to apply changes.

Go to Configuration > Service > Maintenance.

To update via an update server:

1. Click Check to make a connection to the server.

2. Select the appropriate version to download.

To update from a file on your hard disk:

1. Click Browse… to locate and select the firmware file.

2. Click Upload to begin transferring the file.

The device will reboot automatically when the upload is completed successfully. Do not interrupt the firmware installation.

1. Apply power to the BOSCH FLEXIDOME MICRO 3100I NUV-3703-F04-GOV.

2. Find the hardware reset button on the camera block. You may need to remove the camera bubble to access it.

3. Push and hold the reset button for more than 10 seconds. The red LED indicator on the device will begin flashing to show that the hardware reset started.

4. Let the camera complete a self-check. When the self-check completes, the red LED will turn off.

5. Search again for the IP address, access the camera using the web browser, and set the initial password.